Provided by: pppdcapiplugin_3.25+dfsg1-3.7ubuntu1_amd64 
NAME
capiplugin - Plugin for pppd (Point-to-Point Protocol daemon)
SYNOPSIS
pppd [options] plugin capiplugin.so [options for capiplugin]
before pppd 2.4.1:
pppd [options] plugin /usr/lib/pppd/<pppd-version>/capiplugin.so [options for capiplugin]
DESCRIPTION
The capiplugin provides a method to use PPP over ISDN with ISDN controllers that provide a
CAPI2.0 interface. The plugin is responsible for the call setup with CAPI2.0. You can
dial out, wait for incoming calls and set up communication over leased lines. It
implements a feature to reject an incoming call and callback. This feature can also be
used when dialing out. In this case, the party called has to reject the call and call
back soon. When using dial-on-demand it is possible let both parties setup the
connection, that means while the pppd is in dial-on-demand mode not only an outgoing paket
but also an incoming call can trigger the connection setup. This can also combined with
callback to assign the cost to one side only (COSO).
PPPD VERSIONS
The plugin interface of the pppd is binary incompartible between different version of the
pppd. So you need a different capiplugin for every version of the pppd. The different
plugins will be in the directory /usr/lib/ppp/<pppd-version>. Since 2.4.1 pppd checks if
the version of the plugin matches and also search the plugins in these directories. With
pppd versions before 2.4.1 you need to specify the absolute pathname of the plugin.
HOW IT WORKS
The capiplugin registers a new_phase_notifier and its own options to the pppd when loaded.
When the pppd goes into phase SERIALCONN, the capiplugin set up a connection and sets the
global variable devnam. The capiplugin will register a timer function that is called
every second to handle the CAPI messages while pppd is running. To notify pppd when CAPI
messages arrive, the CAPI file desciptor is added to the list of file descriptors which
the pppd monitors for input. Once the connection is set up the pppd will start PPP
negotiation on device devnam. When the pppd enters the DEAD phase, the connection will be
dropped (if it is still active) When operating in dial-on-demand mode with wakeup on
incoming calls, in phase DORMANT the plugin will setup CAPI2.0 to accept incoming calls.
To wakeup pppd when an incoming call arrives, the plugin will generate an UDP paket to the
discard port (9) of the gateway, so don't filter this paket or wakeup by incoming a call
will not work.
MODES OF OPERATION
normal dial out
Simply make a connection, for example to your Internet provider.
Required options: number.
Recommended options: msn.
Other possible options: controller, dialmax, dialtimeout, protocol and redialdelay.
dial out with callback
Call a given number, the called party rejects the call and then calls back.
Required options: number and coso remote.
Recommended options: cli and msn or inmsn.
Other possible options: cbwait, controller, connectdelay, dialtimeout, protocol
dial out on demand
Initiate the connection only on demand, i.e. when data traffic is present and drop
the connection after a fix amount of idle time.
Required options: number.
Required pppd options: demand, connect, idle.
Recommended options: msn.
Other possible options: controller, dialmax, dialtimeout, protocol and redialdelay.
dial out on demand on an incoming phone call
Initiate the connection only on demand, i.e. when data traffic is present or an
incoming phone call is detected and drop the connection after a fix amount of idle
time. This is useful if you are not at home and you want your computer to make a
connection to the internet.
Required options: number and cli.
Required options: number, voicecallwakeup and inmsn and/or cli.
Required pppd options: demand, connect, idle.
Recommended options: msn. Other possible options: controller, dialmax,
dialtimeout, protocol, redialdelay and inmsn.
wait for dial in
Wait for calls and accept incoming calls.
Recommended options: cli and msn or inmsn.
Possible options: connectdelay, controller, dialtimeout, protocol
wait for dial in and call back.
Wait for calls, reject the call and then call back.
Required options: cbnumber.
Recommended options: cli and msn or inmsn.
Other possible options: cbdelay, connectdelay, controller, dialtimeout, protocol
dial on demand and also wait for dial in
Initiate the connection only on demand, i.e. when data traffic is present or when
the other side dial in and drop the connection after a fix amount of idle time.
Required options: number and inmsn and/or cli.
Recommended options: cli and msn or inmsn.
Optional options: coso caller.
Other possible options: cbdelay, connectdelay, controller, dialtimeout, protocol
dial on demand and also wait for dial in with COSO.
Initiate the connection only on demand, i.e. when data traffic is present or when
the other side dial in and drop the connection after a fix amount of idle time. If
option coso local is set, pppd will reject an incoming call from the remote party
and will callback. With the option coso remote set, the remote party should reject
the incoming call and call back.
Required options: number, inmsn and/or cli, coso local or coso remote.
Recommended options: cli and msn or inmsn.
Other possible options: cbdelay, connectdelay, controller, dialtimeout, protocol
leased line
set up a leased line connection, with or without CAPI channel bundling.
Required options: channels. Other possible options:
connectdelay, controller, dialtimeout and protocol
OPTIONS
avmadsl
make an DSL connection with the Fritz!Card DSL controller. The parameters for the
DSL connection will be loaded from file /etc/drdsl/adsl.conf. This file can be
edited or will be created by the program drdsl.
cbdelay <seconds>
Number of seconds to wait before callback, when acting as dial-in server with
callback. Default value is 2 seconds.
cbnumber <phone numbers>
List of phone numbers for callback, separated by commas, when acting as dial-in
server with callback.
cbwait <seconds>
Time to wait for callback before giving up. Default value is 60 seconds.
channels <channel specification>
List of b-channels or ranges to activate leased line mode, separated by commas.
cli <phone numbers>
List of numbers from which incoming calls will be accepted, separated by commas.
clicb The option is retained for compartiblity reasons only. Use option coso local or
coso remote instead.
Enable callback mode. When option number is set, call number and wait for
callback. When option number is not set, wait for incoming call, reject the call
and call back. This option is optional if the cbnumber option is set.
connectdelay <seconds>
Number of seconds to wait after a connection is set up, before PPP negotiation
starts. Default value is 0 seconds. This option is useful when connecting with
protocol modem. Some Internet access servers will hang up if they receive data
immediatly after the connection is established.
controller <controller specification>
For point-to-multipoint <controller specification> is only the CAPI 2.0 controller
number, default is 1. For point-to-point, specify <controller
number>,<ddi>,<length of internal numbers>
controller[1-3] <controller specification>
Like option controller. Used to specify more than one controller
coso caller
No callback is done, the costs are assigned to the caller.
coso local
The costs are assigned to the local party. On an incoming call pppd will reject
the call and callback.
coso remote
The costs are assigned to the remote party. On an outcoming call the remote party
will reject the call and callback.
dialmax <times>
Maximum number of times the list of phone numbers is tried before giving up.
Default value is 4.
If dialmax is set to 0, the list is retried infinitely until a connection is made
(or the process is stopped).
dialtimeout <seconds>
Time to wait for the connection to be established or fail before giving up.
Default value is 60 seconds.
inmsn <msn>
List of phone numbers to monitor for calls, separated by commas. If this option is
not set, the value of option msn is used.
inmsn[1-3] <msn>
List of phone numbers to monitor for calls on controller specified by option
controller[1-3], separated by commas. If this option is not set, the value of
option msn[1-3] is used.
msn <msn>
Phone number used to make outgoing calls. Also used for incoming calls if option
inmsn is not set.
msn[1-3] <msn>
Phone number used to make outgoing calls on controller specified by option
controller[1-3]. Also used for incoming calls if option inmsn[1-3] is not set.
number <phone numbers>
List of phone numbers to call, separated by commas. Every number in the list is
called until a connection can be established. When the end of the list is reached,
the first number is called again. See option dialmax.
numberprefix <prefix>
phone number to dial to access an outside line. For example, numberprefix 0.
numberprefix[1-3] <prefix>
phone number to dial to access an outside line for controller specified by option
controller[1-3]. For example, numberprefix1 0.
protocol hdlc | x75 | v42bis | modem | analogmodem | v110async | v120async
ISDN protocol to use. With hdlc and adskpppoe, the sync option must be added to the
pppd. With x75, v42bis, modem, v110async and v120async the sync option MUST NOT be
enabled. Default value is hdlc. Not all controllers support v42bis, modem and
v120async. Use capiinfo(8) to view which features your controller supports.
redialdelay <seconds>
Number of seconds to wait between redialing. Default value is 5 seconds.
voicewakeup
With this option a incoming voicecall can trigger an outgoing connection setup.
EXAMPLE FOR NORMAL DIAL OUT
Probably the most common use of pppd is to dial out to an ISP. This can be specified with
a command like
pppd call isp
where the /etc/ppp/peers/isp file is set up by the system administrator to resemble the
following:
sync
noauth
defaultroute
name USERNAME
plugin capiplugin.so ®msn MSN
number PHONENUMBER
protocol hdlc
ipcp-accept-local
ipcp-accept-remote
/dev/null
and where the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets are set up by the
system administrator to resemble the following:
USERNAME * PASSWORD *
EXAMPLE OF DIAL OUT WITH CALLBACK
Dial out with callback can be specified with a command like
pppd call isp-callback
where the /etc/ppp/peers/isp-callback file is set up by the system administrator to
resemble the following:
sync
noauth
defaultroute
name USERNAME
plugin capiplugin.so
msn MSN
number PHONENUMBER
coso remote
cli PHONENUMBER
protocol hdlc
ipcp-accept-local
ipcp-accept-remote
/dev/null
and where the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets are set up by the
system administrator to resemble the following:
USERNAME * PASSWORD *
EXAMPLE DIAL OUT ON DEMAND
To dial out on demand and drop the link after 120 seconds idle time on the link add this
line to the /etc/inittab file:
isp:23:respawn:/usr/sbin/pppd call isp demand connect "" idle 120
where the /etc/ppp/peers/isp file is set up by the system administrator to resemble the
following:
sync
noauth
defaultroute
name USERNAME
plugin capiplugin.so ®msn MSN
number PHONENUMBER
protocol hdlc
ipcp-accept-local
ipcp-accept-remote
/dev/null
and where the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets are set up by the
system administrator to resemble the following:
USERNAME * PASSWORD *
EXAMPLE DIAL OUT ON DEMAND AND ON AN INCOMING PHONE CALL
To dial out on demand or on an incoming phone call and drop the link after 120 seconds
idle time on the link add this line to the /etc/inittab file:
isp:23:respawn:/usr/sbin/pppd call isp demand connect "" idle 120
where the /etc/ppp/peers/isp file is set up by the system administrator to resemble the
following:
sync
noauth
defaultroute
name USERNAME
plugin capiplugin.so
msn MSN
number PHONENUMBER
cli VOICEPHONENUMBER
voicecallwakeup
protocol hdlc
ipcp-accept-local
ipcp-accept-remote
/dev/null
and where the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets are set up by the
system administrator to resemble the following:
USERNAME * PASSWORD *
EXAMPLE DIAL OUT ON DEMAND AND ALSO ACCEPT AN INCOMING DATA CALL
To dial out on demand or on an incoming data call and drop the link after 120 seconds idle
time on the link add this line to the /etc/inittab file:
isp:23:respawn:/usr/sbin/pppd call isp demand connect "" idle 120
where the /etc/ppp/peers/isp file is set up by the system administrator to resemble the
following:
sync
noauth
defaultroute
name USERNAME
plugin capiplugin.so
msn MSN
number PHONENUMBER
inmsn MSN
protocol hdlc
ipcp-accept-local
ipcp-accept-remote
/dev/null
and where the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets are set up by the
system administrator to resemble the following:
USERNAME * PASSWORD *
EXAMPLE OF WAIT FOR DIAL IN WITHOUT CLI AUTHENTICATION
Wait for incoming calls, accept them according to options msn, inmsn, and protocol.
Do not provide option cli to the capiplugin. Start a pppd for every b channel.
Authorization is checked using PAP or CHAP and the ip numbers are assigned according to
the /etc/ppp/pap-secrets or /etc/ppp/chap-secrets file. Assume that the server has ip
number 192.168.0.1, the clients are to be assigned the ip numbers starting from
192.168.0.2, and the hostname of the server is "dialinserver". Add these two lines to the
/etc/inittab file:
p0:23:respawn:/usr/sbin/pppd call incoming-noncli
p1:23:respawn:/usr/sbin/pppd call incoming-noncli
where the /etc/ppp/peers/incoming-noncli file is set up to resemble the following:
sync
auth
plugin capiplugin.so
inmsn MSN
protocol hdlc 192.168.0.1:
with the files /etc/ppp/pap-secrets and /etc/ppp/chap-secrets set up to resemble the
following:
user1 dialinserver PASSWORD1 192.168.0.2
user2 dialinserver PASSWORD2 192.168.0.3
EXAMPLE OF WAIT FOR DIAL IN WITH CLI AUTHENTICATION
Wait for incoming calls, accept them according to options msn, inmsn, cli and protocol.
Start a pppd for every client. Assume that the server has ip number 192.168.0.1 and the
clients are to be assigned the ip numbers starting from 192.168.0.2. Add these three
lines to the /etc/inittab file:
p0:23:respawn:/usr/sbin/pppd call incoming-cli cli 04711 192.168.0.1:192.168.0.2
p1:23:respawn:/usr/sbin/pppd call incoming-cli cli 04712 192.168.0.1:192.168.0.3
p2:23:respawn:/usr/sbin/pppd call incoming-cli cli 04713 192.168.0.1:192.168.0.4
where the /etc/ppp/peers/incoming-cli file is set up to resemble the following:
sync
noauth
plugin capiplugin.so
inmsn MSN
protocol hdlc
EXAMPLE OF WAIT FOR DIAL IN WITH CLI AUTHENTICATION AND CALLBACK
Wait for incoming calls, accept them according to options msn, inmsn, cli and protocol,
reject incoming calls and call back.
Start a pppd for every client. Assume that the server has ip number 192.168.0.1 and the
clients are to be assigned the ip numbers starting from 192.168.0.2. Add these three
lines to the /etc/inittab file.
p0:23:respawn:/usr/sbin/pppd call incoming-cli cli 04711 cbnumber 4711
192.168.0.1:192.168.0.2
p1:23:respawn:/usr/sbin/pppd call incoming-cli cli 04712 cbnumber 4712
192.168.0.1:192.168.0.3
p2:23:respawn:/usr/sbin/pppd call incoming-cli cli 04713 cbnumber 4713
192.168.0.1:192.168.0.4
where the /etc/ppp/peers/incoming-cli file is set up to resemble the following:
sync
noauth
plugin capiplugin.so
inmsn MSN
protocol hdlc
EXAMPLE OF A LEASED LINE CONNECTION WITH HDLC
Assume that the server has ip number 192.168.0.1 and the peer has the ip number
192.168.0.2. Add this line to the /etc/inittab file:
p0:23:respawn:/usr/sbin/pppd call leased-hdlc controller 1 channels 1
192.168.0.1:192.168.0.2
where the /etc/ppp/peers/leased-hdlc file is set up to resemble the following:
sync
noauth
lcp-echo-interval 5
lcp-echo-failure 3
lcp-max-configure 50
lcp-max-terminate 2
noccp
noipx
persist
plugin capiplugin.so
protocol hdlc
EXAMPLE OF A LEASED LINE CONNECTION WITH V42BIS
Assume that the server has ip number 192.168.0.1 and the peer has the ip number
192.168.0.2. Add this line to the /etc/inittab file for server 1 (192.168.0.1):
p0:23:respawn:/usr/sbin/pppd call leased-v42bis controller 1 channels 1
192.168.0.1:192.168.0.2
and this line to the /etc/inittab file for server 1 (192.168.0.2):
p0:23:respawn:/usr/sbin/pppd call leased-v42bis controller 1 channels p1
192.168.0.2:192.168.0.1
where the /etc/ppp/peers/leased-v42bis file is set up to resemble the following:
sync
noauth
lcp-echo-interval 5
lcp-echo-failure 3
lcp-max-configure 50
lcp-max-terminate 2
noccp
noipx
persist
plugin capiplugin.so
protocol v42bis
CAVEATS
Every pppd awaiting incoming calls can receive an incoming call first. So when two pppds
are started to monitor the same MSN, one with CLI Authentication and the other without,
the following can happen:
The Client with the CLI specified to the first pppd calls, but the pppd without the
cli option receives the call first and accepts it.
To combine CLI Authentication and PAP/CHAP Authentication, use one MSN for CLI
authenticated calls and another for the PAP/CHAP authenticated calls.
DIAGNOSTICS
Messages are sent to the syslog daemon just as in normal pppd operation; see the pppd
manual page.
SEE ALSO
pppd(8), capiinfo(8), capiinit(8), capictrl(8)
AUTHORS
Carsten Paeth (calle@calle.in-berlin.de)
AVM GmbH Berlin (info@avm.de)
CAPIPLUGIN(8)