Provided by: iptables_1.6.0-2ubuntu3_amd64 
NAME
iptables/ip6tables — administration tool for IPv4/IPv6 packet filtering and NAT
SYNOPSIS
iptables [-t table] {-A|-C|-D} chain rule-specification
ip6tables [-t table] {-A|-C|-D} chain rule-specification
iptables [-t table] -I chain [rulenum] rule-specification
iptables [-t table] -R chain rulenum rule-specification
iptables [-t table] -D chain rulenum
iptables [-t table] -S [chain [rulenum]]
iptables [-t table] {-F|-L|-Z} [chain [rulenum]] [options...]
iptables [-t table] -N chain
iptables [-t table] -X [chain]
iptables [-t table] -P chain target
iptables [-t table] -E old-chain-name new-chain-name
rule-specification = [matches...] [target]
match = -m matchname [per-match-options]
target = -j targetname [per-target-options]
DESCRIPTION
Iptables and ip6tables are used to set up, maintain, and inspect the tables of IPv4 and IPv6 packet
filter rules in the Linux kernel. Several different tables may be defined. Each table contains a number
of built-in chains and may also contain user-defined chains.
Each chain is a list of rules which can match a set of packets. Each rule specifies what to do with a
packet that matches. This is called a `target', which may be a jump to a user-defined chain in the same
table.
TARGETS
A firewall rule specifies criteria for a packet and a target. If the packet does not match, the next
rule in the chain is examined; if it does match, then the next rule is specified by the value of the
target, which can be the name of a user-defined chain, one of the targets described in
iptables-extensions(8), or one of the special values ACCEPT, DROP or RETURN.
ACCEPT means to let the packet through. DROP means to drop the packet on the floor. RETURN means stop
traversing this chain and resume at the next rule in the previous (calling) chain. If the end of a
built-in chain is reached or a rule in a built-in chain with target RETURN is matched, the target
specified by the chain policy determines the fate of the packet.
TABLES
There are currently five independent tables (which tables are present at any time depends on the kernel
configuration options and which modules are present).
-t, --table table
This option specifies the packet matching table which the command should operate on. If the
kernel is configured with automatic module loading, an attempt will be made to load the
appropriate module for that table if it is not already there.
The tables are as follows:
filter:
This is the default table (if no -t option is passed). It contains the built-in chains INPUT
(for packets destined to local sockets), FORWARD (for packets being routed through the box),
and OUTPUT (for locally-generated packets).
nat:
This table is consulted when a packet that creates a new connection is encountered. It
consists of three built-ins: PREROUTING (for altering packets as soon as they come in), OUTPUT
(for altering locally-generated packets before routing), and POSTROUTING (for altering packets
as they are about to go out). IPv6 NAT support is available since kernel 3.7.
mangle:
This table is used for specialized packet alteration. Until kernel 2.4.17 it had two built-in
chains: PREROUTING (for altering incoming packets before routing) and OUTPUT (for altering
locally-generated packets before routing). Since kernel 2.4.18, three other built-in chains
are also supported: INPUT (for packets coming into the box itself), FORWARD (for altering
packets being routed through the box), and POSTROUTING (for altering packets as they are about
to go out).
raw:
This table is used mainly for configuring exemptions from connection tracking in combination
with the NOTRACK target. It registers at the netfilter hooks with higher priority and is thus
called before ip_conntrack, or any other IP tables. It provides the following built-in
chains: PREROUTING (for packets arriving via any network interface) OUTPUT (for packets
generated by local processes)
security:
This table is used for Mandatory Access Control (MAC) networking rules, such as those enabled
by the SECMARK and CONNSECMARK targets. Mandatory Access Control is implemented by Linux
Security Modules such as SELinux. The security table is called after the filter table,
allowing any Discretionary Access Control (DAC) rules in the filter table to take effect
before MAC rules. This table provides the following built-in chains: INPUT (for packets
coming into the box itself), OUTPUT (for altering locally-generated packets before routing),
and FORWARD (for altering packets being routed through the box).
OPTIONS
The options that are recognized by iptables and ip6tables can be divided into several different groups.
COMMANDS
These options specify the desired action to perform. Only one of them can be specified on the command
line unless otherwise stated below. For long versions of the command and option names, you need to use
only enough letters to ensure that iptables can differentiate it from all other options.
-A, --append chain rule-specification
Append one or more rules to the end of the selected chain. When the source and/or destination
names resolve to more than one address, a rule will be added for each possible address
combination.
-C, --check chain rule-specification
Check whether a rule matching the specification does exist in the selected chain. This command
uses the same logic as -D to find a matching entry, but does not alter the existing iptables
configuration and uses its exit code to indicate success or failure.
-D, --delete chain rule-specification
-D, --delete chain rulenum
Delete one or more rules from the selected chain. There are two versions of this command: the
rule can be specified as a number in the chain (starting at 1 for the first rule) or a rule to
match.
-I, --insert chain [rulenum] rule-specification
Insert one or more rules in the selected chain as the given rule number. So, if the rule number
is 1, the rule or rules are inserted at the head of the chain. This is also the default if no
rule number is specified.
-R, --replace chain rulenum rule-specification
Replace a rule in the selected chain. If the source and/or destination names resolve to multiple
addresses, the command will fail. Rules are numbered starting at 1.
-L, --list [chain]
List all rules in the selected chain. If no chain is selected, all chains are listed. Like every
other iptables command, it applies to the specified table (filter is the default), so NAT rules
get listed by
iptables -t nat -n -L
Please note that it is often used with the -n option, in order to avoid long reverse DNS lookups.
It is legal to specify the -Z (zero) option as well, in which case the chain(s) will be atomically
listed and zeroed. The exact output is affected by the other arguments given. The exact rules are
suppressed until you use
iptables -L -v
-S, --list-rules [chain]
Print all rules in the selected chain. If no chain is selected, all chains are printed like
iptables-save. Like every other iptables command, it applies to the specified table (filter is the
default).
-F, --flush [chain]
Flush the selected chain (all the chains in the table if none is given). This is equivalent to
deleting all the rules one by one.
-Z, --zero [chain [rulenum]]
Zero the packet and byte counters in all chains, or only the given chain, or only the given rule
in a chain. It is legal to specify the -L, --list (list) option as well, to see the counters
immediately before they are cleared. (See above.)
-N, --new-chain chain
Create a new user-defined chain by the given name. There must be no target of that name already.
-X, --delete-chain [chain]
Delete the optional user-defined chain specified. There must be no references to the chain. If
there are, you must delete or replace the referring rules before the chain can be deleted. The
chain must be empty, i.e. not contain any rules. If no argument is given, it will attempt to
delete every non-builtin chain in the table.
-P, --policy chain target
Set the policy for the built-in (non-user-defined) chain to the given target. The policy target
must be either ACCEPT or DROP.
-E, --rename-chain old-chain new-chain
Rename the user specified chain to the user supplied name. This is cosmetic, and has no effect on
the structure of the table.
-h Help. Give a (currently very brief) description of the command syntax.
PARAMETERS
The following parameters make up a rule specification (as used in the add, delete, insert, replace and
append commands).
-4, --ipv4
This option has no effect in iptables and iptables-restore. If a rule using the -4 option is
inserted with (and only with) ip6tables-restore, it will be silently ignored. Any other uses will
throw an error. This option allows IPv4 and IPv6 rules in a single rule file for use with both
iptables-restore and ip6tables-restore.
-6, --ipv6
If a rule using the -6 option is inserted with (and only with) iptables-restore, it will be
silently ignored. Any other uses will throw an error. This option allows IPv4 and IPv6 rules in a
single rule file for use with both iptables-restore and ip6tables-restore. This option has no
effect in ip6tables and ip6tables-restore.
[!] -p, --protocol protocol
The protocol of the rule or of the packet to check. The specified protocol can be one of tcp,
udp, udplite, icmp, icmpv6,esp, ah, sctp, mh or the special keyword "all", or it can be a numeric
value, representing one of these protocols or a different one. A protocol name from
/etc/protocols is also allowed. A "!" argument before the protocol inverts the test. The number
zero is equivalent to all. "all" will match with all protocols and is taken as default when this
option is omitted. Note that, in ip6tables, IPv6 extension headers except esp are not allowed.
esp and ipv6-nonext can be used with Kernel version 2.6.11 or later. The number zero is
equivalent to all, which means that you cannot test the protocol field for the value 0 directly.
To match on a HBH header, even if it were the last, you cannot use -p 0, but always need -m hbh.
[!] -s, --source address[/mask][,...]
Source specification. Address can be either a network name, a hostname, a network IP address (with
/mask), or a plain IP address. Hostnames will be resolved once only, before the rule is submitted
to the kernel. Please note that specifying any name to be resolved with a remote query such as
DNS is a really bad idea. The mask can be either an ipv4 network mask (for iptables) or a plain
number, specifying the number of 1's at the left side of the network mask. Thus, an iptables mask
of 24 is equivalent to 255.255.255.0. A "!" argument before the address specification inverts the
sense of the address. The flag --src is an alias for this option. Multiple addresses can be
specified, but this will expand to multiple rules (when adding with -A), or will cause multiple
rules to be deleted (with -D).
[!] -d, --destination address[/mask][,...]
Destination specification. See the description of the -s (source) flag for a detailed description
of the syntax. The flag --dst is an alias for this option.
-m, --match match
Specifies a match to use, that is, an extension module that tests for a specific property. The set
of matches make up the condition under which a target is invoked. Matches are evaluated first to
last as specified on the command line and work in short-circuit fashion, i.e. if one extension
yields false, evaluation will stop.
-j, --jump target
This specifies the target of the rule; i.e., what to do if the packet matches it. The target can
be a user-defined chain (other than the one this rule is in), one of the special builtin targets
which decide the fate of the packet immediately, or an extension (see EXTENSIONS below). If this
option is omitted in a rule (and -g is not used), then matching the rule will have no effect on
the packet's fate, but the counters on the rule will be incremented.
-g, --goto chain
This specifies that the processing should continue in a user specified chain. Unlike the --jump
option return will not continue processing in this chain but instead in the chain that called us
via --jump.
[!] -i, --in-interface name
Name of an interface via which a packet was received (only for packets entering the INPUT, FORWARD
and PREROUTING chains). When the "!" argument is used before the interface name, the sense is
inverted. If the interface name ends in a "+", then any interface which begins with this name
will match. If this option is omitted, any interface name will match.
[!] -o, --out-interface name
Name of an interface via which a packet is going to be sent (for packets entering the FORWARD,
OUTPUT and POSTROUTING chains). When the "!" argument is used before the interface name, the
sense is inverted. If the interface name ends in a "+", then any interface which begins with this
name will match. If this option is omitted, any interface name will match.
[!] -f, --fragment
This means that the rule only refers to second and further IPv4 fragments of fragmented packets.
Since there is no way to tell the source or destination ports of such a packet (or ICMP type),
such a packet will not match any rules which specify them. When the "!" argument precedes the
"-f" flag, the rule will only match head fragments, or unfragmented packets. This option is IPv4
specific, it is not available in ip6tables.
-c, --set-counters packets bytes
This enables the administrator to initialize the packet and byte counters of a rule (during
INSERT, APPEND, REPLACE operations).
OTHER OPTIONS
The following additional options can be specified:
-v, --verbose
Verbose output. This option makes the list command show the interface name, the rule options (if
any), and the TOS masks. The packet and byte counters are also listed, with the suffix 'K', 'M'
or 'G' for 1000, 1,000,000 and 1,000,000,000 multipliers respectively (but see the -x flag to
change this). For appending, insertion, deletion and replacement, this causes detailed
information on the rule or rules to be printed. -v may be specified multiple times to possibly
emit more detailed debug statements.
-w, --wait [seconds]
Wait for the xtables lock. To prevent multiple instances of the program from running
concurrently, an attempt will be made to obtain an exclusive lock at launch. By default, the
program will exit if the lock cannot be obtained. This option will make the program wait
(indefinitely or for optional seconds) until the exclusive lock can be obtained.
-n, --numeric
Numeric output. IP addresses and port numbers will be printed in numeric format. By default, the
program will try to display them as host names, network names, or services (whenever applicable).
-x, --exact
Expand numbers. Display the exact value of the packet and byte counters, instead of only the
rounded number in K's (multiples of 1000) M's (multiples of 1000K) or G's (multiples of 1000M).
This option is only relevant for the -L command.
--line-numbers
When listing rules, add line numbers to the beginning of each rule, corresponding to that rule's
position in the chain.
--modprobe=command
When adding or inserting rules into a chain, use command to load any necessary modules (targets,
match extensions, etc).
MATCH AND TARGET EXTENSIONS
iptables can use extended packet matching and target modules. A list of these is available in the
iptables-extensions(8) manpage.
DIAGNOSTICS
Various error messages are printed to standard error. The exit code is 0 for correct functioning.
Errors which appear to be caused by invalid or abused command line parameters cause an exit code of 2,
and other errors cause an exit code of 1.
BUGS
Bugs? What's this? ;-) Well, you might want to have a look at http://bugzilla.netfilter.org/
COMPATIBILITY WITH IPCHAINS
This iptables is very similar to ipchains by Rusty Russell. The main difference is that the chains INPUT
and OUTPUT are only traversed for packets coming into the local host and originating from the local host
respectively. Hence every packet only passes through one of the three chains (except loopback traffic,
which involves both INPUT and OUTPUT chains); previously a forwarded packet would pass through all three.
The other main difference is that -i refers to the input interface; -o refers to the output interface,
and both are available for packets entering the FORWARD chain.
The various forms of NAT have been separated out; iptables is a pure packet filter when using the default
`filter' table, with optional extension modules. This should simplify much of the previous confusion
over the combination of IP masquerading and packet filtering seen previously. So the following options
are handled differently:
-j MASQ
-M -S
-M -L
There are several other changes in iptables.
SEE ALSO
iptables-apply(8), iptables-save(8), iptables-restore(8), iptables-extensions(8), The packet-filtering-HOWTO details iptables usage for packet filtering, the NAT-HOWTO details NAT, the netfilter-extensions-HOWTO details the extensions that are not in the standard distribution, and the netfilter-hacking-HOWTO details the netfilter internals. See http://www.netfilter.org/.
AUTHORS
Rusty Russell originally wrote iptables, in early consultation with Michael Neuling.
Marc Boucher made Rusty abandon ipnatctl by lobbying for a generic packet selection framework in
iptables, then wrote the mangle table, the owner match, the mark stuff, and ran around doing cool stuff
everywhere.
James Morris wrote the TOS target, and tos match.
Jozsef Kadlecsik wrote the REJECT target.
Harald Welte wrote the ULOG and NFQUEUE target, the new libiptc, as well as the TTL, DSCP, ECN matches
and targets.
The Netfilter Core Team is: Jozsef Kadlecsik, Patrick McHardy, Pablo Neira Ayuso, Eric Leblond and
Florian Westphal. Emeritus Core Team members are: Marc Boucher, Martin Josefsson, Yasuyuki Kozakai, James
Morris, Harald Welte and Rusty Russell.
Man page originally written by Herve Eychenne <rv@wallfire.org>.
VERSION
This manual page applies to iptables/ip6tables 1.6.0.