Provided by: freebsd-manpages_10.1~RC1-1_all bug


     ieee80211_scan — 802.11 scanning support


     #include <net80211/ieee80211_var.h>

     ieee80211_start_scan(struct ieee80211vap *, int flags, u_int duration, u_int mindwell,
         u_int maxdwell, u_int nssid, const struct ieee80211_scan_ssid ssids[]);

     ieee80211_check_scan(struct ieee80211vap *, int flags, u_int duration, u_int mindwell,
         u_int maxdwell, u_int nssid, const struct ieee80211_scan_ssid ssids[]);

     ieee80211_check_scan_current(struct ieee80211vap *);

     ieee80211_bg_scan(struct ieee80211vap *, int);

     ieee80211_cancel_scan(struct ieee80211vap *);

     ieee80211_cancel_scan_any(struct ieee80211vap *);

     ieee80211_scan_next(struct ieee80211vap *);

     ieee80211_scan_done(struct ieee80211vap *);

     ieee80211_probe_curchan(struct ieee80211vap *, int);

     ieee80211_add_scan(struct ieee80211vap *, const struct ieee80211_scanparams *,
         const struct ieee80211_frame *, int subtype, int rssi, int noise);

     ieee80211_scan_timeout(struct ieee80211com *);

     ieee80211_scan_assoc_fail(struct ieee80211vap *, const uint8_t mac[IEEE80211_ADDR_LEN],
         int reason);

     ieee80211_scan_flush(struct ieee80211vap *);

     ieee80211_scan_iterate(struct ieee80211vap *, ieee80211_scan_iter_func, void *);

     ieee80211_scan_dump_channels(const struct ieee80211_scan_state *);

     ieee80211_scanner_register(enum ieee80211_opmode, const struct ieee80211_scanner *);

     ieee80211_scanner_unregister(enum ieee80211_opmode, const struct ieee80211_scanner *);

     ieee80211_scanner_unregister_all(const struct ieee80211_scanner *);

     const struct ieee80211_scanner *
     ieee80211_scanner_get(enum ieee80211_opmode);


     The net80211 software layer provides an extensible framework for scanning.  Scanning is the
     procedure by which a station locates a BSS to join (in infrastructure and IBSS mode), or a
     channel to use (when operating as an AP or an IBSS master).  Scans are either “active” or
     “passive”.  An active scan causes one or more ProbeRequest frames to be sent on visiting
     each channel.  A passive request causes each channel in the scan set to be visited but no
     frames to be transmitted; the station only listens for traffic.  Note that active scanning
     may still need to listen for traffic before sending ProbeRequest frames depending on
     regulatory constraints.

     A scan operation involves constructing a set of channels to inspect (the scan set), visiting
     each channel and collecting information (e.g. what BSS are present), and then analyzing the
     results to make decisions such as which BSS to join.  This process needs to be as fast as
     possible so net80211 does things like intelligently construct scan sets and dwell on a
     channel only as long as necessary.  Scan results are cached and the scan cache is used to
     avoid scanning when possible and to enable roaming between access points when operating in
     infrastructure mode.

     Scanning is handled by pluggable modules that implement policy per-operating mode.  The core
     scanning support provides an infrastructure to support these modules and exports a common
     API to the rest of the net80211 layer.  Policy modules decide what channels to visit, what
     state to record to make decisions, and selects the final station/channel to return as the
     result of a scan.

     Scanning is done synchronously when initially bringing a vap to an operational state and
     optionally in the background to maintain the scan cache for doing roaming and rogue AP
     monitoring.  Scanning is not tied to the net80211 state machine that governs vaps except for
     linkage to the IEEE80211_S_SCAN state.  Only one vap at a time may be scanning; this
     scheduling policy is handled in ieee80211_new_state() and is transparent to scanning code.

     Scanning is controlled by a set of parameters that (potentially) constrains the channel set
     and any desired SSID's and BSSID's.  net80211 comes with a standard scanner module that
     works with all available operating modes and supports “background scanning” and “roaming”


     Scanning modules use a registration mechanism to hook into the net80211 layer.  Use
     ieee80211_scanner_register() to register a scan module for a particular operating mode and
     ieee80211_scanner_unregister() or ieee80211_scanner_unregister_all() to clear entries
     (typically on module unload).  Only one scanner module can be registered at any time for an
     operating mode.


     Scanning operations are usually managed by the net80211 layer.  Drivers must provide
     ic_scan_start and ic_scan_stop methods that are called at the start of a scan and when the
     work is done; these should handle work such as enabling receive of Beacon and ProbeResponse
     frames and disable any BSSID matching.  The ic_set_channel method is used to change channels
     while scanning.  net80211 will generate ProbeRequest frames and transmit them using the
     ic_raw_xmit method.  Frames received while scanning are dispatched to net80211 using the
     normal receive path.  Devices that off-load scan work to firmware most easily mesh with
     net80211 by operating on a channel-at-a-time basis as this defers control to net80211's scan
     machine scheduler.  But multi-channel scanning is supported if the driver manually
     dispatches results using ieee80211_add_scan() routine to enter results into the scan cache.


     Scan requests occur by way of the IEEE80211_SCAN_REQUEST ioctl or through a change in a
     vap's state machine that requires scanning.  In both cases the scan cache can be checked
     first and, if it is deemed suitably “warm” then it's contents are used without leaving the
     current channel.  To start a scan without checking the cache ieee80211_start_scan() can be
     called; otherwise ieee80211_check_scan() can be used to first check the scan cache, kicking
     off a scan if the cache contents are out of date.  There is also
     ieee80211_check_scan_current() which is a shorthand for using previously set scan parameters
     for checking the scan cache and then scanning.

     Background scanning is done using ieee80211_bg_scan() in a co-routine fashion.  The first
     call to this routine will start a background scan that runs for a limited period of time
     before returning to the BSS channel.  Subsequent calls advance through the scan set until
     all channels are visited.  Typically these later calls are timed to allow receipt of frames
     buffered by an access point for the station.

     A scan operation can be canceled using ieee80211_cancel_scan() if it was initiated by the
     specified vap, or ieee80211_cancel_scan_any() to force termination regardless which vap
     started it.  These requests are mostly used by net80211 in the transmit path to cancel
     background scans when frames are to be sent.  Drivers should not need to use these calls (or
     most of the calls described on this page).

     The ieee80211_scan_next() and ieee80211_scan_done() routines do explicit iteration through
     the scan set and should not normally be used by drivers.  ieee80211_probe_curchan() handles
     the work of transmitting ProbeRequest frames when visiting a channel during an active scan.
     When the channel attributes are marked with IEEE80211_CHAN_PASSIVE this function will
     arrange that before any frame is transmitted 802.11 traffic is first received (in order to
     comply with regulatory constraints).

     Min/max dwell time parameters are used to constrain time spent visiting a channel.  The
     maximum dwell time constrains the time spent listening for traffic.  The minimum dwell time
     is used to reduce this time--when it is reached and one or more frames have been received
     then an immediate channel change will be done.  Drivers can override this behaviour through
     the iv_scan_mindwell method.


     The scan cache contents are managed by the scan policy module and are opaque outside this
     module.  The net80211 scan framework defines API's for interacting.  The validity of the
     scan cache contents are controlled by iv_scanvalid which is exported to user space through
     the IEEE80211_SCAN_VALID request.

     The cache contents can be explicitly flushed with ieee80211_scan_flush() or by setting the
     IEEE80211_SCAN_FLUSH flag when starting a scan operation.

     Scan cache entries are created with the ieee80211_add_scan() routine; usually on receipt of
     Beacon or ProbeResponse frames.  Existing entries are typically updated based on the latest
     information though some information such as RSSI and noise floor readings may be combined to
     present an average.

     The cache contents is aged through ieee80211_scan_timeout() calls.  Typically these happen
     together with other station table activity; every IEEE80211_INACT_WAIT seconds (default 15).

     Individual cache entries are marked usable with ieee80211_scan_assoc_success() and faulty
     with ieee80211_scan_assoc_fail() with the latter taking an argument to identify if there was
     no response to Authentication/Association requests or if a negative response was received
     (which might hasten cache eviction or blacklist the entry).

     The cache contents can be viewed using the ieee80211_scan_iterate() call.  Cache entries are
     exported in a public format that is exported to user applications through the
     IEEE80211_SCAN_RESULTS request.


     ioctl(2), ieee80211(9), ieee80211_proto(9)