Provided by: oss4-base_4.2-build2010-5ubuntu3~18.04.2_amd64 
NAME
oss_sblive - Creative Labs Sound Blaster Live/Audigy family driver.
DESCRIPTION
Open Sound System driver for Creative Labs Sound Blaster Live!, Audigy, Audigy2, Audigy2-Value and sound
cards.
The sblive driver supports:
• 8-48Khz Playback/Recording
• 8 or 16 bits
• SPDIF digital output and Input
• Multi channel 5.1 (Live!) and 7.1 (Audigy) output.
AC3 passthrough is only supported on Audigy series of the soundcards.
OTHER SIMILAR CARDS
There are several Sound Blaster cards that are also called as Live or Audigy. However these cards are
based on entirely different hardware design and they are not compatible with this driver.
• Sound Blaster Live 5.1 card is used in some Dell machines but it's driven by the emu10k1x driver.
• Sound Blaster AudigyLS and Live 7.1 models are driven by the audigyls driver of OSS.
SBLIVE COMBO SPDIF AND AUDIO JACKS
Most models of Live! and Audigy cards have an orange combo jack that is used both for the analog
center/LFE output and for digital DIN (S/PDIF) output. The output mode is selected by a driver
configuration option (seel below) which should be set to proper value depending on the actual speaker
configuration.
• Noisy analog center/LFE output. The orange combo jack at the rear plate of the Live/Audigy card is
shared between the digital DIN and the analog center/LFE outputs. In digital DIN mode (default) you
will hear very noisy output from the speakers connected to this output jack. If you have analog
center/LFE (subwoofer) speakers connected then you need to turn off the sblive_digital_din (or
audigy_digital_din) option.
• There is a new configuration option to enable/disable the "digital DIN" output. By default the digital
DIN interface is enabled which disables the center/LFE analog output (uses the same combo jack). By
setting the sblive_digital_din (or audigy_digital_din) option to 0 you can enable the analog C/LFE
output feature. When digital DIN is disabled you can still get S/PDIF (or AC3) output from the digital
(optical/coax) outputs of the optional livedrive unit.
SBLIVE MIXER
SB Live cards have actually two mixer chips. In OSS both of them are controlled together. However only
limited set of features can be controlled using ordinary mixer programs (such as the mixer applet
included in OSS). Majority of features can only be accessed using the ossmix and ossxmix programs
included in OSS.
The AC97 mixer is used to control volumes of the back bracket inputs (mic and line in) and the _analog_
CD input connector on the soundcard. The 'mic' volume controls the level of the rear bracket microphone
input sent directly to the front (only front) speakers. The 'line' and 'cd' controls do the same for the
back bracket line in connector and the on board analog CD input connector. It's usually recommended to
set these volumes to 0.
Another function of the AC97 mixer is selecting the signal that is passed to the master mixer (for
example for recording). One of the 'mic', 'line' or ’cd' signals can be routed to the master mixer by
selecting that device as the recording source in the AC97 mixer. The 'rec' volume control slider can be
used to adjust the signal strength. The 'igain' control doesn't usually have any effect but some hardware
revisions may use it for controlling the microphone recording level.
SBLIVE MASTER MIXER
Other mixer functions are handled by the DSP engine of the EMU 10k1 chip. Most input signals (including
all digital signals and LiveDrive inputs).
There are only two master mixer settings that can be controlled using all mixer programs. The 'vol'
setting is the master output volume that affects both the front and rear speakers and the headphone
output (digital output volumes are not affected). The 'pcm' setting controls volumes of all PCM playback
channels (/dev/dsp#).
In addition to volume sliders most inputs have a stereo VU meter pair (only in ossxmix) that can be used
to monitor the input and to adjust the input levels properly.
The master mixer consists of several sections that are:
• Primary section: This section has two settings. The "spkmode" setting selects how front/rear speakers
are used for PCM playback (outputs from programs using /dev/dsp#). The possible settings are FRONT,
REAR and FRONT+REAR. The default is FRONT+REAR. Change this setting if you like to get PCM playback
only from front or rear speakers. The "autoreset" flag is used to control the "/dev" section.
• "/dev" section: This section controls the volumes of each /dev/dsp# device file supported by the
device (there are 8 of them at this moment). These volumes will return back to maximum every time the
device is opened. However this can be disabled by setting the 'autoreset' option to OFF. The ossxmix
program has special ability to show the application using the particular /dev/dsp device (for layout
reasons only the first 4 characters of the program name are shown).
• The equalizer section: This section controls the graphic equalizer for front speakers only.
• The front rear, and record sections: These three identical sections control the levels of external
inputs and PCM playback (/dev/dsp# devices) to be sent to the front/rear speakers and to the recording
device. The CD Analog audio will only be heard from the FRONT speakers.
SBLIVE RECORDING
Before recording anything you need to set the volumes in the recording section properly. To enable
recording from the AC97 connected inputs (mic, line in and analog CD) use the AC97 mixer to select the
desired input and then tune the input level using the rec (and igain) setting.
Finally set the 'ac97' slider in the record section of the master mixer so that the recording level is
suitable.
The OSS drivers permit recording any application that's currently playing.
To record audio that's playing on any of the SB Live channels:
• Turn down the AC97 control in the "record" section. This prevents any audio being fed to the soundcard
from MIC/Line-in/CD-in from getting mixed with the audio produced by the application that's currently
playing.
• Type ossrecord -s<sampling rate> -b<bits/sample> -c<channels> test.wav
• To stop recording press <Ctrl-c> and then you can play back the test.wav file using ossplay command.
RECORDING ISSUES: In most cases noise is caused by the microphone input or some other (unused)
input. Use the ossxmix program to turn off all unused inputs and finally save the current mixer
settings (see below).
Hint: Look at the VU meter panels of ossxmix. It's usually very easy to locate the noise source by
looking which input has some signal coming from it.
WARNING! If you turn off some of the signals in recording section or the AC97 mixer section this
affects all subsequent recordings. Remember to raise the volume prior doing any recording. After
that decrease the volumes again if necessary.
SBLIVE HARDWARE MIXING
You can use /dev/oss/oss_sblive0/ pcm0-pcm7 to play multiple audio programs using the hardware mixing.
Simply specify the device name with the application. A simple test is to do the following: ossplay
-d/dev/oss/oss_sblive0/pcm0 <file1.wav> & ossplay -d/dev/oss/oss_sblive0/pcm1 <file2.wav> & ossplay
-d/dev/oss/oss_sblive0/pcm2 <file3.wav> &
You should hear all three wav files playing simultaneously.
NOTE: Some apps may desire the old /dev/dspN names. e.g. /dev/dsp0 - /dev/dsp7.
NOTE: You can increase the number of output devices from the standard 8 devices to 32 device. For this,
run soundconf, select Set configuration options and look for the entry "sblive_device", now type any
number between 1 and 32 for the number of channels you wish. You can also do this manually by editing
oss_sblive.conf and inserting sblive_devices=XX entry, e.g.: sblive_devices=27
CDROM CONNNECTIONS
There are two alternative ways to connect audio signal from a CD-ROM drive tor the SB Live soundcard. You
can use a (three wire) analog cable or a (2 wire) digital cable. OSS now supports both of these choices.
Note that there are separate mixer settings for both of these connections.
The analog CD-ROM wire is connected to the AC97 code chip and this method works in most cases. To route
the analog CD -input to the (front) speakers you need to raise the volume of the 'cd' control in mixer.
However if you like to hear the analog CD input both from the front and rears speakers you need to do
this in slightly different way (please read the description of the mixer above).
The digital connection works only with CD-ROM drives that has support for it. Note that some CD-ROM
drives having this digital output connector use a different signal level than the one required by SB
Live. This means that the digital connection doesn't work with all CD-ROM drives (no sound). If you have
problems with the digital connection you should use the analog one. When using the the digital CD input
you may need to adjust the 'digcd' volumes using ossxmix (or ossmix).
It should be noted that SB Live works internally at 48 kHz. This means that all S/PDIF input signals are
automatically sample rate converted to 48 kHz. If you record from a 44.1 kHz (CD-ROM) and save the
result to a 44.1 kHz file the signal will be sample rate converted twice. First from the 44.1 kHz input
to internal 48 kHz and then back to 44.1 kHz. While the sample rate converter of SB Live is very precise
this will cause some change. This should not be any problem when doing audio recordings but it may cause
unwanted results when transferring digital data (such as AC3/DTS) using the S/PDIF the interface.
CONFIGURATION OPTIONS
• sblive_digital_din=<0|1> - This option is to enable/disable the "digital DIN" output of SB Live. By
default the digital DIN interface is disabled which enables the center/LFE analog output (uses the
same combo jack). By setting the sblive_digital_din option to 0 you can enable the analog Center/LFE
output feature. When digital DIN is disabled you can still get S/PDIF (or AC3) output from the digital
(optical/coax) outputs of the optional livedrive unit. Default: 0=analog output.
• audigy_digital_din=<0|1> - same as "sblive_digital_din" option except for the Audigy soundcards.
Default: 1=digital output.
• sblive_devices=<1..32> - Number of audio devices to be configured.
LIMITATION
• SB Live! devices will not work in Sparc systems due to PCI addressing limitations. Only Audigy/Audigy2
models work under Sparc.
• EMU Wavetable MIDI synthesizer is not supported
• AC3 passthrough only supported on Audigy/Audigy but not on SB Live! devices.
FILES
/etc/oss4/conf/oss_sblive.conf Device configuration file
AUTHOR
4Front Technologies
13 November 2019 oss_sblive(7)