Provided by: netplan.io_0.104-0ubuntu2~20.04.6_amd64 
NAME
netplan - YAML network configuration abstraction for various backends
SYNOPSIS
netplan [ COMMAND | help ]
COMMANDS
See netplan help for a list of available commands on this system.
DESCRIPTION
Introduction
Distribution installers, cloud instantiation, image builds for particular devices, or any other way to
deploy an operating system put its desired network configuration into YAML configuration file(s). During
early boot, the netplan “network renderer” runs which reads /{lib,etc,run}/netplan/*.yaml and writes con‐
figuration to /run to hand off control of devices to the specified networking daemon.
• Configured devices get handled by systemd-networkd by default, unless explicitly marked as managed by a
specific renderer (NetworkManager)
• Devices not covered by the network config do not get touched at all.
• Usable in initramfs (few dependencies and fast)
• No persistent generated config, only original YAML config
• Parser supports multiple config files to allow applications like libvirt or lxd to package up expected
network config (virbr0, lxdbr0), or to change the global default policy to use NetworkManager for
everything.
• Retains the flexibility to change backends/policy later or adjust to removing NetworkManager, as gener‐
ated configuration is ephemeral.
General structure
netplan’s configuration files use the YAML (http://yaml.org/spec/1.1/current.html) format. All
/{lib,etc,run}/netplan/*.yaml are considered. Lexicographically later files (regardless of in which di‐
rectory they are) amend (new mapping keys) or override (same mapping keys) previous ones. A file in
/run/netplan completely shadows a file with same name in /etc/netplan, and a file in either of those di‐
rectories shadows a file with the same name in /lib/netplan.
The top-level node in a netplan configuration file is a network: mapping that contains version: 2 (the
YAML currently being used by curtin, MaaS, etc. is version 1), and then device definitions grouped by
their type, such as ethernets:, modems:, wifis:, or bridges:. These are the types that our renderer can
understand and are supported by our backends.
Each type block contains device definitions as a map where the keys (called “configuration IDs”) are de‐
fined as below.
Device configuration IDs
The key names below the per-device-type definition maps (like ethernets:) are called “ID”s. They must be
unique throughout the entire set of configuration files. Their primary purpose is to serve as anchor
names for composite devices, for example to enumerate the members of a bridge that is currently being de‐
fined.
(Since 0.97) If an interface is defined with an ID in a configuration file; it will be brought up by the
applicable renderer. To not have netplan touch an interface at all, it should be completely omitted from
the netplan configuration files.
There are two physically/structurally different classes of device definitions, and the ID field has a
different interpretation for each:
Physical devices
(Examples: ethernet, modem, wifi) These can dynamically come and go between reboots and even dur‐
ing runtime (hotplugging). In the generic case, they can be selected by match: rules on desired
properties, such as name/name pattern, MAC address, driver, or device paths. In general these
will match any number of devices (unless they refer to properties which are unique such as the
full path or MAC address), so without further knowledge about the hardware these will always be
considered as a group.
It is valid to specify no match rules at all, in which case the ID field is simply the interface
name to be matched. This is mostly useful if you want to keep simple cases simple, and it’s how
network device configuration has been done for a long time.
If there are match: rules, then the ID field is a purely opaque name which is only being used for
references from definitions of compound devices in the config.
Virtual devices
(Examples: veth, bridge, bond) These are fully under the control of the config file(s) and the
network stack. I. e. these devices are being created instead of matched. Thus match: and
set-name: are not applicable for these, and the ID field is the name of the created virtual de‐
vice.
Common properties for physical device types
Note: Some options will not work reliably for devices matched by name only and rendered by networkd, due
to interactions with device renaming in udev. Match devices by MAC when setting options like: wakeonlan
or *-offload.
match (mapping)
This selects a subset of available physical devices by various hardware properties. The following
configuration will then apply to all matching devices, as soon as they appear. All specified
properties must match.
name (scalar)
Current interface name. Globs are supported, and the primary use case for matching on
names, as selecting one fixed name can be more easily achieved with having no match: at all
and just using the ID (see above). (NetworkManager: as of v1.14.0)
macaddress (scalar)
Device’s MAC address in the form “XX:XX:XX:XX:XX:XX”. Globs are not allowed.
driver (scalar or sequence of scalars) – sequence since 0.104
Kernel driver name, corresponding to the DRIVER udev property. A sequence of globs is sup‐
ported, any of which must match. Matching on driver is only supported with networkd.
Examples:
• all cards on second PCI bus:
match:
name: enp2*
• fixed MAC address:
match:
macaddress: 11:22:33:AA:BB:FF
• first card of driver ixgbe:
match:
driver: ixgbe
name: en*s0
• first card with a driver matching bcmgenet or smsc*:
match:
driver: ["bcmgenet", "smsc*"]
name: en*
set-name (scalar)
When matching on unique properties such as path or MAC, or with additional assumptions such as
“there will only ever be one wifi device”, match rules can be written so that they only match one
device. Then this property can be used to give that device a more specific/desirable/nicer name
than the default from udev’s ifnames. Any additional device that satisfies the match rules will
then fail to get renamed and keep the original kernel name (and dmesg will show an error).
wakeonlan (bool)
Enable wake on LAN. Off by default.
emit-lldp (bool) – since 0.99
(networkd backend only) Whether to emit LLDP packets. Off by default.
receive-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware offload for checksumming of ingress
network packets is enabled (disabled). When unset, the kernel’s default will be used.
transmit-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware offload for checksumming of egress
network packets is enabled (disabled). When unset, the kernel’s default will be used.
tcp-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP Segmentation Offload (TSO) is enabled
(disabled). When unset, the kernel’s default will be used.
tcp6-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP6 Segmentation Offload (tx-tcp6-segmenta‐
tion) is enabled (disabled). When unset, the kernel’s default will be used.
generic-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic Segmentation Offload (GSO) is enabled
(disabled). When unset, the kernel’s default will be used.
generic-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic Receive Offload (GRO) is enabled (dis‐
abled). When unset, the kernel’s default will be used.
large-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Large Receive Offload (LRO) is enabled (dis‐
abled). When unset, the kernel’s default will be used.
openvswitch (mapping) – since 0.100
This provides additional configuration for the network device for openvswitch. If openvswitch is
not available on the system, netplan treats the presence of openvswitch configuration as an error.
Any supported network device that is declared with the openvswitch mapping (or any bond/bridge
that includes an interface with an openvswitch configuration) will be created in openvswitch in‐
stead of the defined renderer. In the case of a vlan definition declared the same way, netplan
will create a fake VLAN bridge in openvswitch with the requested vlan properties.
external-ids (mapping) – since 0.100
Passed-through directly to OpenVSwitch
other-config (mapping) – since 0.100
Passed-through directly to OpenVSwitch
lacp (scalar) – since 0.100
Valid for bond interfaces. Accepts active, passive or off (the default).
fail-mode (scalar) – since 0.100
Valid for bridge interfaces. Accepts secure or standalone (the default).
mcast-snooping (bool) – since 0.100
Valid for bridge interfaces. False by default.
protocols (sequence of scalars) – since 0.100
Valid for bridge interfaces or the network section. List of protocols to be used when ne‐
gotiating a connection with the controller. Accepts OpenFlow10, OpenFlow11, OpenFlow12,
OpenFlow13, OpenFlow14, OpenFlow15 and OpenFlow16.
rstp (bool) – since 0.100
Valid for bridge interfaces. False by default.
controller (mapping) – since 0.100
Valid for bridge interfaces. Specify an external OpenFlow controller.
addresses (sequence of scalars)
Set the list of addresses to use for the controller targets. The syntax of these
addresses is as defined in ovs-vsctl(8). Example: addresses: [tcp:127.0.0.1:6653,
"ssl:[fe80::1234%eth0]:6653"]
connection-mode (scalar)
Set the connection mode for the controller. Supported options are in-band and
out-of-band. The default is in-band.
ports (sequence of sequence of scalars) – since 0.100
OpenvSwitch patch ports. Each port is declared as a pair of names which can be referenced
as interfaces in dependent virtual devices (bonds, bridges).
Example:
openvswitch:
ports:
- [patch0-1, patch1-0]
ssl (mapping) – since 0.100
Valid for global openvswitch settings. Options for configuring SSL server endpoint for the
switch.
ca-cert (scalar)
Path to a file containing the CA certificate to be used.
certificate (scalar)
Path to a file containing the server certificate.
private-key (scalar)
Path to a file containing the private key for the server.
Common properties for all device types
renderer (scalar)
Use the given networking backend for this definition. Currently supported are networkd and Net‐
workManager. This property can be specified globally in network:, for a device type (in e. g.
ethernets:) or for a particular device definition. Default is networkd.
(Since 0.99) The renderer property has one additional acceptable value for vlan objects (i. e.
defined in vlans:): sriov. If a vlan is defined with the sriov renderer for an SR-IOV Virtual
Function interface, this causes netplan to set up a hardware VLAN filter for it. There can be on‐
ly one defined per VF.
dhcp4 (bool)
Enable DHCP for IPv4. Off by default.
dhcp6 (bool)
Enable DHCP for IPv6. Off by default. This covers both stateless DHCP - where the DHCP server
supplies information like DNS nameservers but not the IP address - and stateful DHCP, where the
server provides both the address and the other information.
If you are in an IPv6-only environment with completely stateless autoconfiguration (SLAAC with
RDNSS), this option can be set to cause the interface to be brought up. (Setting accept-ra alone
is not sufficient.) Autoconfiguration will still honour the contents of the router advertisement
and only use DHCP if requested in the RA.
Note that rdnssd(8) is required to use RDNSS with networkd. No extra software is required for
NetworkManager.
ipv6-mtu (scalar) – since 0.98
Set the IPv6 MTU (only supported with networkd backend). Note that needing to set this is an un‐
usual requirement.
Requires feature: ipv6-mtu
ipv6-privacy (bool)
Enable IPv6 Privacy Extensions (RFC 4941) for the specified interface, and prefer temporary ad‐
dresses. Defaults to false - no privacy extensions. There is currently no way to have a private
address but prefer the public address.
link-local (sequence of scalars)
Configure the link-local addresses to bring up. Valid options are `ipv4' and `ipv6', which re‐
spectively allow enabling IPv4 and IPv6 link local addressing. If this field is not defined, the
default is to enable only IPv6 link-local addresses. If the field is defined but configured as an
empty set, IPv6 link-local addresses are disabled as well as IPv4 link- local addresses.
This feature enables or disables link-local addresses for a protocol, but the actual implementa‐
tion differs per backend. On networkd, this directly changes the behavior and may add an extra
address on an interface. When using the NetworkManager backend, enabling link-local has no effect
if the interface also has DHCP enabled.
Example to enable only IPv4 link-local: link-local: [ ipv4 ] Example to enable all link-local ad‐
dresses: link-local: [ ipv4, ipv6 ] Example to disable all link-local addresses: link-local: [ ]
ignore-carrier (bool) – since 0.104
(networkd backend only) Allow the specified interface to be configured even if it has no carrier.
critical (bool)
Designate the connection as “critical to the system”, meaning that special care will be taken by
to not release the assigned IP when the daemon is restarted. (not recognized by NetworkManager)
dhcp-identifier (scalar)
(networkd backend only) Sets the source of DHCPv4 client identifier. If mac is specified, the MAC
address of the link is used. If this option is omitted, or if duid is specified, networkd will
generate an RFC4361-compliant client identifier for the interface by combining the link’s IAID and
DUID.
dhcp4-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides section below.
dhcp6-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides section below.
accept-ra (bool)
Accept Router Advertisement that would have the kernel configure IPv6 by itself. When enabled,
accept Router Advertisements. When disabled, do not respond to Router Advertisements. If unset
use the host kernel default setting.
addresses (sequence of scalars and mappings)
Add static addresses to the interface in addition to the ones received through DHCP or RA. Each
sequence entry is in CIDR notation, i. e. of the form addr/prefixlen. addr is an IPv4 or IPv6
address as recognized by inet_pton(3) and prefixlen the number of bits of the subnet.
For virtual devices (bridges, bonds, vlan) if there is no address configured and DHCP is disabled,
the interface may still be brought online, but will not be addressable from the network.
In addition to the addresses themselves one can specify configuration parameters as mappings.
Current supported options are:
lifetime (scalar) – since 0.100
Default: forever. This can be forever or 0 and corresponds to the PreferredLifetime option
in systemd-networkd’s Address section. Currently supported on the networkd backend only.
label (scalar) – since 0.100
An IP address label, equivalent to the ip address label command. Currently supported on
the networkd backend only.
Example: addresses: [192.168.14.2/24, "2001:1::1/64"]
Example:
ethernets:
eth0:
addresses:
- 10.0.0.15/24:
lifetime: 0
label: "maas"
- "2001:1::1/64"
ipv6-address-generation (scalar) – since 0.99
Configure method for creating the address for use with RFC4862 IPv6 Stateless Address Autoconfigu‐
ration (only supported with NetworkManager backend). Possible values are eui64 or stable-privacy.
ipv6-address-token (scalar) – since 0.100
Define an IPv6 address token for creating a static interface identifier for IPv6 Stateless Address
Autoconfiguration. This is mutually exclusive with ipv6-address-generation.
gateway4, gateway6 (scalar)
Deprecated, see Default routes. Set default gateway for IPv4/6, for manual address configuration.
This requires setting addresses too. Gateway IPs must be in a form recognized by inet_pton(3).
There should only be a single gateway per IP address family set in your global config, to make it
unambiguous. If you need multiple default routes, please define them via routing-policy.
Example for IPv4: gateway4: 172.16.0.1 Example for IPv6: gateway6: "2001:4::1"
nameservers (mapping)
Set DNS servers and search domains, for manual address configuration. There are two supported
fields: addresses: is a list of IPv4 or IPv6 addresses similar to gateway*, and search: is a list
of search domains.
Example:
ethernets:
id0:
[...]
nameservers:
search: [lab, home]
addresses: [8.8.8.8, "FEDC::1"]
macaddress (scalar)
Set the device’s MAC address. The MAC address must be in the form “XX:XX:XX:XX:XX:XX”.
Note: This will not work reliably for devices matched by name only and rendered by networkd, due
to interactions with device renaming in udev. Match devices by MAC when setting MAC addresses.
Example:
ethernets:
id0:
match:
macaddress: 52:54:00:6b:3c:58
[...]
macaddress: 52:54:00:6b:3c:59
mtu (scalar)
Set the Maximum Transmission Unit for the interface. The default is 1500. Valid values depend on
your network interface.
Note: This will not work reliably for devices matched by name only and rendered by networkd, due
to interactions with device renaming in udev. Match devices by MAC when setting MTU.
optional (bool)
An optional device is not required for booting. Normally, networkd will wait some time for device
to become configured before proceeding with booting. However, if a device is marked as optional,
networkd will not wait for it. This is only supported by networkd, and the default is false.
Example:
ethernets:
eth7:
# this is plugged into a test network that is often
# down - don't wait for it to come up during boot.
dhcp4: true
optional: true
optional-addresses (sequence of scalars)
Specify types of addresses that are not required for a device to be considered online. This
changes the behavior of backends at boot time to avoid waiting for addresses that are marked op‐
tional, and thus consider the interface as “usable” sooner. This does not disable these address‐
es, which will be brought up anyway.
Example:
ethernets:
eth7:
dhcp4: true
dhcp6: true
optional-addresses: [ ipv4-ll, dhcp6 ]
activation-mode (scalar) – since 0.103
Allows specifying the management policy of the selected interface. By default, netplan brings up
any configured interface if possible. Using the activation-mode setting users can override that
behavior by either specifying manual, to hand over control over the interface state to the admin‐
istrator or (for networkd backend only) off to force the link in a down state at all times. Any
interface with activation-mode defined is implicitly considered optional. Supported officially as
of networkd v248+.
Example:
ethernets:
eth1:
# this interface will not be put into an UP state automatically
dhcp4: true
activation-mode: manual
routes (sequence of mappings)
Configure static routing for the device; see the Routing section below.
routing-policy (sequence of mappings)
Configure policy routing for the device; see the Routing section below.
DHCP Overrides
Several DHCP behavior overrides are available. Most currently only have any effect when using the net‐
workd backend, with the exception of use-routes and route-metric.
Overrides only have an effect if the corresponding dhcp4 or dhcp6 is set to true.
If both dhcp4 and dhcp6 are true, the networkd backend requires that dhcp4-overrides and dhcp6-overrides
contain the same keys and values. If the values do not match, an error will be shown and the network
configuration will not be applied.
When using the NetworkManager backend, different values may be specified for dhcp4-overrides and
dhcp6-overrides, and will be applied to the DHCP client processes as specified in the netplan YAML.
dhcp4-overrides, dhcp6-overrides (mapping)
The dhcp4-overrides and dhcp6-overrides mappings override the default DHCP behavior.
use-dns (bool)
Default: true. When true, the DNS servers received from the DHCP server will be used and
take precedence over any statically configured ones. Currently only has an effect on the
networkd backend.
use-ntp (bool)
Default: true. When true, the NTP servers received from the DHCP server will be used by
systemd-timesyncd and take precedence over any statically configured ones. Currently only
has an effect on the networkd backend.
send-hostname (bool)
Default: true. When true, the machine’s hostname will be sent to the DHCP server. Cur‐
rently only has an effect on the networkd backend.
use-hostname (bool)
Default: true. When true, the hostname received from the DHCP server will be set as the
transient hostname of the system. Currently only has an effect on the networkd backend.
use-mtu (bool)
Default: true. When true, the MTU received from the DHCP server will be set as the MTU of
the network interface. When false, the MTU advertised by the DHCP server will be ignored.
Currently only has an effect on the networkd backend.
hostname (scalar)
Use this value for the hostname which is sent to the DHCP server, instead of machine’s
hostname. Currently only has an effect on the networkd backend.
use-routes (bool)
Default: true. When true, the routes received from the DHCP server will be installed in
the routing table normally. When set to false, routes from the DHCP server will be ig‐
nored: in this case, the user is responsible for adding static routes if necessary for cor‐
rect network operation. This allows users to avoid installing a default gateway for inter‐
faces configured via DHCP. Available for both the networkd and NetworkManager backends.
route-metric (scalar)
Use this value for default metric for automatically-added routes. Use this to prioritize
routes for devices by setting a lower metric on a preferred interface. Available for both
the networkd and NetworkManager backends.
use-domains (scalar) – since 0.98
Takes a boolean, or the special value “route”. When true, the domain name received from
the DHCP server will be used as DNS search domain over this link, similar to the effect of
the Domains= setting. If set to “route”, the domain name received from the DHCP server
will be used for routing DNS queries only, but not for searching, similar to the effect of
the Domains= setting when the argument is prefixed with “~”.
Requires feature: dhcp-use-domains
Routing
Complex routing is possible with netplan. Standard static routes as well as policy routing using routing
tables are supported via the networkd backend.
These options are available for all types of interfaces.
Default routes
The most common need for routing concerns the definition of default routes to reach the wider Internet.
Those default routes can only defined once per IP family and routing table. A typical example would look
like the following:
eth0:
[...]
routes:
- to: default # could be 0/0 or 0.0.0.0/0 optionally
via: 10.0.0.1
metric: 100
on-link: true
- to: default # could be ::/0 optionally
via: cf02:de:ad:be:ef::2
eth1:
[...]
routes:
- to: default
via: 172.134.67.1
metric: 100
on-link: true
table: 76 # Not on the main routing table, does not conflict with the eth0 default route
routes (mapping)
The routes block defines standard static routes for an interface. At least to must be specified.
If type is local or nat a default scope of host is assumed. If type is unicast and no gateway
(via) is given or type is broadcast, multicast or anycast a default scope of link is assumend.
Otherwise, a global scope is the default setting.
For from, to, and via, both IPv4 and IPv6 addresses are recognized, and must be in the form ad‐
dr/prefixlen or addr.
from (scalar)
Set a source IP address for traffic going through the route. (NetworkManager: as of
v1.8.0)
to (scalar)
Destination address for the route.
via (scalar)
Address to the gateway to use for this route.
on-link (bool)
When set to “true”, specifies that the route is directly connected to the interface. (Net‐
workManager: as of v1.12.0 for IPv4 and v1.18.0 for IPv6)
metric (scalar)
The relative priority of the route. Must be a positive integer value.
type (scalar)
The type of route. Valid options are “unicast” (default), “anycast”, “blackhole”, “broad‐
cast”, “local”, “multicast”, “nat”, “prohibit”, “throw”, “unreachable” or “xresolve”.
scope (scalar)
The route scope, how wide-ranging it is to the network. Possible values are “global”,
“link”, or “host”.
table (scalar)
The table number to use for the route. In some scenarios, it may be useful to set routes
in a separate routing table. It may also be used to refer to routing policy rules which
also accept a table parameter. Allowed values are positive integers starting from 1. Some
values are already in use to refer to specific routing tables: see /etc/iproute2/rt_tables.
(NetworkManager: as of v1.10.0)
mtu (scalar) – since 0.101
The MTU to be used for the route, in bytes. Must be a positive integer value.
congestion-window (scalar) – since 0.102
The congestion window to be used for the route, represented by number of segments. Must be
a positive integer value.
advertised-receive-window (scalar) – since 0.102
The receive window to be advertised for the route, represented by number of segments. Must
be a positive integer value.
routing-policy (mapping)
The routing-policy block defines extra routing policy for a network, where traffic may be handled
specially based on the source IP, firewall marking, etc.
For from, to, both IPv4 and IPv6 addresses are recognized, and must be in the form addr/prefixlen
or addr.
from (scalar)
Set a source IP address to match traffic for this policy rule.
to (scalar)
Match on traffic going to the specified destination.
table (scalar)
The table number to match for the route. In some scenarios, it may be useful to set routes
in a separate routing table. It may also be used to refer to routes which also accept a
table parameter. Allowed values are positive integers starting from 1. Some values are
already in use to refer to specific routing tables: see /etc/iproute2/rt_tables.
priority (scalar)
Specify a priority for the routing policy rule, to influence the order in which routing
rules are processed. A higher number means lower priority: rules are processed in order by
increasing priority number.
mark (scalar)
Have this routing policy rule match on traffic that has been marked by the iptables fire‐
wall with this value. Allowed values are positive integers starting from 1.
type-of-service (scalar)
Match this policy rule based on the type of service number applied to the traffic.
Authentication
Netplan supports advanced authentication settings for ethernet and wifi interfaces, as well as individual
wifi networks, by means of the auth block.
auth (mapping)
Specifies authentication settings for a device of type ethernets:, or an access-points: entry on a
wifis: device.
The auth block supports the following properties:
key-management (scalar)
The supported key management modes are none (no key management); psk (WPA with pre-shared
key, common for home wifi); eap (WPA with EAP, common for enterprise wifi); and 802.1x
(used primarily for wired Ethernet connections).
password (scalar)
The password string for EAP, or the pre-shared key for WPA-PSK.
The following properties can be used if key-management is eap or 802.1x:
method (scalar)
The EAP method to use. The supported EAP methods are tls (TLS), peap (Protected EAP), and
ttls (Tunneled TLS).
identity (scalar)
The identity to use for EAP.
anonymous-identity (scalar)
The identity to pass over the unencrypted channel if the chosen EAP method supports passing
a different tunnelled identity.
ca-certificate (scalar)
Path to a file with one or more trusted certificate authority (CA) certificates.
client-certificate (scalar)
Path to a file containing the certificate to be used by the client during authentication.
client-key (scalar)
Path to a file containing the private key corresponding to client-certificate.
client-key-password (scalar)
Password to use to decrypt the private key specified in client-key if it is encrypted.
phase2-auth (scalar) – since 0.99
Phase 2 authentication mechanism.
Properties for device type ethernets:
Ethernet device definitions, beyond common ones described above, also support some additional properties
that can be used for SR-IOV devices.
link (scalar) – since 0.99
(SR-IOV devices only) The link property declares the device as a Virtual Function of the selected
Physical Function device, as identified by the given netplan id.
Example:
ethernets:
enp1: {...}
enp1s16f1:
link: enp1
virtual-function-count (scalar) – since 0.99
(SR-IOV devices only) In certain special cases VFs might need to be configured outside of netplan.
For such configurations virtual-function-count can be optionally used to set an explicit number of
Virtual Functions for the given Physical Function. If unset, the default is to create only as
many VFs as are defined in the netplan configuration. This should be used for special cases only.
Requires feature: sriov
embedded-switch-mode (scalar) – since 0.104
(SR-IOV devices only) Change the operational mode of the embedded switch of a supported SmartNIC
PCI device (e.g. Mellanox ConnectX-5). Possible values are switchdev or legacy, if unspecified
the vendor’s default configuration is used.
Requires feature: eswitch-mode
delay-virtual-functions-rebind (bool) – since 0.104
(SR-IOV devices only) Delay rebinding of SR-IOV virtual functions to its driver after changing the
embedded-switch-mode setting to a later stage. Can be enabled when bonding/VF LAG is in use. De‐
faults to false.
Requires feature: eswitch-mode
Properties for device type modems:
GSM/CDMA modem configuration is only supported for the NetworkManager backend. systemd-networkd does not
support modems.
Requires feature: modems
apn (scalar) – since 0.99
Set the carrier APN (Access Point Name). This can be omitted if auto-config is enabled.
auto-config (bool) – since 0.99
Specify whether to try and autoconfigure the modem by doing a lookup of the carrier against the
Mobile Broadband Provider database. This may not work for all carriers.
device-id (scalar) – since 0.99
Specify the device ID (as given by the WWAN management service) of the modem to match. This can
be found using mmcli.
network-id (scalar) – since 0.99
Specify the Network ID (GSM LAI format). If this is specified, the device will not roam networks.
number (scalar) – since 0.99
The number to dial to establish the connection to the mobile broadband network. (Deprecated for
GSM)
password (scalar) – since 0.99
Specify the password used to authenticate with the carrier network. This can be omitted if au‐
to-config is enabled.
pin (scalar) – since 0.99
Specify the SIM PIN to allow it to operate if a PIN is set.
sim-id (scalar) – since 0.99
Specify the SIM unique identifier (as given by the WWAN management service) which this connection
applies to. If given, the connection will apply to any device also allowed by device-id which
contains a SIM card matching the given identifier.
sim-operator-id (scalar) – since 0.99
Specify the MCC/MNC string (such as “310260” or “21601”) which identifies the carrier that this
connection should apply to. If given, the connection will apply to any device also allowed by de‐
vice-id and sim-id which contains a SIM card provisioned by the given operator.
username (scalar) – since 0.99
Specify the username used to authentiate with the carrier network. This can be omitted if au‐
to-config is enabled.
Properties for device type wifis:
Note that systemd-networkd does not natively support wifi, so you need wpasupplicant installed if you let
the networkd renderer handle wifi.
access-points (mapping)
This provides pre-configured connections to NetworkManager. Note that users can of course select
other access points/SSIDs. The keys of the mapping are the SSIDs, and the values are mappings
with the following supported properties:
password (scalar)
Enable WPA2 authentication and set the passphrase for it. If neither this nor an auth
block are given, the network is assumed to be open. The setting
password: "S3kr1t"
is equivalent to
auth:
key-management: psk
password: "S3kr1t"
mode (scalar)
Possible access point modes are infrastructure (the default), ap (create an access point to
which other devices can connect), and adhoc (peer to peer networks without a central access
point). ap is only supported with NetworkManager.
bssid (scalar) – since 0.99
If specified, directs the device to only associate with the given access point.
band (scalar) – since 0.99
Possible bands are 5GHz (for 5GHz 802.11a) and 2.4GHz (for 2.4GHz 802.11), do not restrict
the 802.11 frequency band of the network if unset (the default).
channel (scalar) – since 0.99
Wireless channel to use for the Wi-Fi connection. Because channel numbers overlap between
bands, this property takes effect only if the band property is also set.
hidden (bool) – since 0.100
Set to true to change the SSID scan technique for connecting to hidden WiFi networks. Note
this may have slower performance compared to false (the default) when connecting to pub‐
licly broadcast SSIDs.
wakeonwlan (sequence of scalars) – since 0.99
This enables WakeOnWLan on supported devices. Not all drivers support all options. May be any
combination of any, disconnect, magic_pkt, gtk_rekey_failure, eap_identity_req, four_way_hand‐
shake, rfkill_release or tcp (NetworkManager only). Or the exclusive default flag (the default).
Properties for device type bridges:
interfaces (sequence of scalars)
All devices matching this ID list will be added to the bridge. This may be an empty list, in
which case the bridge will be brought online with no member interfaces.
Example:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bridges:
br0:
interfaces: [switchports]
parameters (mapping)
Customization parameters for special bridging options. Time intervals may need to be expressed as
a number of seconds or milliseconds: the default value type is specified below. If necessary,
time intervals can be qualified using a time suffix (such as “s” for seconds, “ms” for millisec‐
onds) to allow for more control over its behavior.
ageing-time (scalar)
Set the period of time to keep a MAC address in the forwarding database after a packet is
received. This maps to the AgeingTimeSec= property when the networkd renderer is used. If
no time suffix is specified, the value will be interpreted as seconds.
priority (scalar)
Set the priority value for the bridge. This value should be a number between 0 and 65535.
Lower values mean higher priority. The bridge with the higher priority will be elected as
the root bridge.
port-priority (scalar)
Set the port priority to . The priority value is a number between 0 and 63. This metric
is used in the designated port and root port selection algorithms.
forward-delay (scalar)
Specify the period of time the bridge will remain in Listening and Learning states before
getting to the Forwarding state. This field maps to the ForwardDelaySec= property for the
networkd renderer. If no time suffix is specified, the value will be interpreted as sec‐
onds.
hello-time (scalar)
Specify the interval between two hello packets being sent out from the root and designated
bridges. Hello packets communicate information about the network topology. When the net‐
workd renderer is used, this maps to the HelloTimeSec= property. If no time suffix is
specified, the value will be interpreted as seconds.
max-age (scalar)
Set the maximum age of a hello packet. If the last hello packet is older than that value,
the bridge will attempt to become the root bridge. This maps to the MaxAgeSec= property
when the networkd renderer is used. If no time suffix is specified, the value will be in‐
terpreted as seconds.
path-cost (scalar)
Set the cost of a path on the bridge. Faster interfaces should have a lower cost. This
allows a finer control on the network topology so that the fastest paths are available
whenever possible.
stp (bool)
Define whether the bridge should use Spanning Tree Protocol. The default value is “true”,
which means that Spanning Tree should be used.
Properties for device type bonds:
interfaces (sequence of scalars)
All devices matching this ID list will be added to the bond.
Example:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bonds:
bond0:
interfaces: [switchports]
parameters (mapping)
Customization parameters for special bonding options. Time intervals may need to be expressed as
a number of seconds or milliseconds: the default value type is specified below. If necessary,
time intervals can be qualified using a time suffix (such as “s” for seconds, “ms” for millisec‐
onds) to allow for more control over its behavior.
mode (scalar)
Set the bonding mode used for the interfaces. The default is balance-rr (round robin).
Possible values are balance-rr, active-backup, balance-xor, broadcast, 802.3ad, bal‐
ance-tlb, and balance-alb. For OpenVSwitch active-backup and the additional modes bal‐
ance-tcp and balance-slb are supported.
lacp-rate (scalar)
Set the rate at which LACPDUs are transmitted. This is only useful in 802.3ad mode. Pos‐
sible values are slow (30 seconds, default), and fast (every second).
mii-monitor-interval (scalar)
Specifies the interval for MII monitoring (verifying if an interface of the bond has carri‐
er). The default is 0; which disables MII monitoring. This is equivalent to the MIIMoni‐
torSec= field for the networkd backend. If no time suffix is specified, the value will be
interpreted as milliseconds.
min-links (scalar)
The minimum number of links up in a bond to consider the bond interface to be up.
transmit-hash-policy (scalar)
Specifies the transmit hash policy for the selection of slaves. This is only useful in
balance-xor, 802.3ad and balance-tlb modes. Possible values are layer2, layer3+4, lay‐
er2+3, encap2+3, and encap3+4.
ad-select (scalar)
Set the aggregation selection mode. Possible values are stable, bandwidth, and count.
This option is only used in 802.3ad mode.
all-slaves-active (bool)
If the bond should drop duplicate frames received on inactive ports, set this option to
false. If they should be delivered, set this option to true. The default value is false,
and is the desirable behavior in most situations.
arp-interval (scalar)
Set the interval value for how frequently ARP link monitoring should happen. The default
value is 0, which disables ARP monitoring. For the networkd backend, this maps to the
ARPIntervalSec= property. If no time suffix is specified, the value will be interpreted as
milliseconds.
arp-ip-targets (sequence of scalars)
IPs of other hosts on the link which should be sent ARP requests in order to validate that
a slave is up. This option is only used when arp-interval is set to a value other than 0.
At least one IP address must be given for ARP link monitoring to function. Only IPv4 ad‐
dresses are supported. You can specify up to 16 IP addresses. The default value is an
empty list.
arp-validate (scalar)
Configure how ARP replies are to be validated when using ARP link monitoring. Possible
values are none, active, backup, and all.
arp-all-targets (scalar)
Specify whether to use any ARP IP target being up as sufficient for a slave to be consid‐
ered up; or if all the targets must be up. This is only used for active-backup mode when
arp-validate is enabled. Possible values are any and all.
up-delay (scalar)
Specify the delay before enabling a link once the link is physically up. The default value
is 0. This maps to the UpDelaySec= property for the networkd renderer. This option is on‐
ly valid for the miimon link monitor. If no time suffix is specified, the value will be
interpreted as milliseconds.
down-delay (scalar)
Specify the delay before disabling a link once the link has been lost. The default value
is 0. This maps to the DownDelaySec= property for the networkd renderer. This option is
only valid for the miimon link monitor. If no time suffix is specified, the value will be
interpreted as milliseconds.
fail-over-mac-policy (scalar)
Set whether to set all slaves to the same MAC address when adding them to the bond, or how
else the system should handle MAC addresses. The possible values are none, active, and
follow.
gratuitous-arp (scalar)
Specify how many ARP packets to send after failover. Once a link is up on a new slave, a
notification is sent and possibly repeated if this value is set to a number greater than 1.
The default value is 1 and valid values are between 1 and 255. This only affects ac‐
tive-backup mode.
For historical reasons, the misspelling gratuitious-arp is also accepted and has the same
function.
packets-per-slave (scalar)
In balance-rr mode, specifies the number of packets to transmit on a slave before switching
to the next. When this value is set to 0, slaves are chosen at random. Allowable values
are between 0 and 65535. The default value is 1. This setting is only used in balance-rr
mode.
primary-reselect-policy (scalar)
Set the reselection policy for the primary slave. On failure of the active slave, the sys‐
tem will use this policy to decide how the new active slave will be chosen and how recovery
will be handled. The possible values are always, better, and failure.
resend-igmp (scalar)
In modes balance-rr, active-backup, balance-tlb and balance-alb, a failover can switch IGMP
traffic from one slave to another.
This parameter specifies how many IGMP membership reports are issued on a failover event.
Values range from 0 to 255. 0 disables sending membership reports. Otherwise, the first
membership report is sent on failover and subsequent reports are sent at 200ms intervals.
learn-packet-interval (scalar)
Specify the interval between sending learning packets to each slave. The value range is
between 1 and 0x7fffffff. The default value is 1. This option only affects balance-tlb
and balance-alb modes. Using the networkd renderer, this field maps to the LearnPacket‐
IntervalSec= property. If no time suffix is specified, the value will be interpreted as
seconds.
primary (scalar)
Specify a device to be used as a primary slave, or preferred device to use as a slave for
the bond (ie. the preferred device to send data through), whenever it is available. This
only affects active-backup, balance-alb, and balance-tlb modes.
Properties for device type tunnels:
Tunnels allow traffic to pass as if it was between systems on the same local network, although systems
may be far from each other but reachable via the Internet. They may be used to support IPv6 traffic on a
network where the ISP does not provide the service, or to extend and “connect” separate local networks.
Please see https://en.wikipedia.org/wiki/Tunneling_protocol for more general information about tunnels.
mode (scalar)
Defines the tunnel mode. Valid options are sit, gre, ip6gre, ipip, ipip6, ip6ip6, vti, vti6 and
wireguard. Additionally, the networkd backend also supports gretap and ip6gretap modes. In addi‐
tion, the NetworkManager backend supports isatap tunnels.
local (scalar)
Defines the address of the local endpoint of the tunnel.
remote (scalar)
Defines the address of the remote endpoint of the tunnel.
ttl (scalar) – since 0.103
Defines the TTL of the tunnel.
key (scalar or mapping)
Define keys to use for the tunnel. The key can be a number or a dotted quad (an IPv4 address).
For wireguard it can be a base64-encoded private key or (as of networkd v242+) an absolute path to
a file, containing the private key (since 0.100). It is used for identification of IP transforms.
This is only required for vti and vti6 when using the networkd backend, and for gre or ip6gre tun‐
nels when using the NetworkManager backend.
This field may be used as a scalar (meaning that a single key is specified and to be used for in‐
put, output and private key), or as a mapping, where you can further specify input/output/private.
input (scalar)
The input key for the tunnel
output (scalar)
The output key for the tunnel
private (scalar) – since 0.100
A base64-encoded private key required for WireGuard tunnels. When the systemd-networkd
backend (v242+) is used, this can also be an absolute path to a file containing the private
key.
keys (scalar or mapping)
Alternate name for the key field. See above.
Examples:
tunnels:
tun0:
mode: gre
local: ...
remote: ...
keys:
input: 1234
output: 5678
tunnels:
tun0:
mode: vti6
local: ...
remote: ...
key: 59568549
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
shared: /path/to/shared.key
...
key: mNb7OIIXTdgW4khM7OFlzJ+UPs7lmcWHV7xjPgakMkQ=
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
...
keys:
private: /path/to/priv.key
WireGuard specific keys:
mark (scalar) – since 0.100
Firewall mark for outgoing WireGuard packets from this interface, optional.
port (scalar) – since 0.100
UDP port to listen at or auto. Optional, defaults to auto.
peers (sequence of mappings) – since 0.100
A list of peers, each having keys documented below.
Example:
tunnels:
wg0:
mode: wireguard
key: /path/to/private.key
mark: 42
port: 5182
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
keepalive: 23
endpoint: 1.2.3.4:5
- keys:
public: M9nt4YujIOmNrRmpIRTmYSfMdrpvE7u6WkG8FY8WjG4=
shared: /some/shared.key
allowed-ips: [10.10.10.20/24]
keepalive: 22
endpoint: 5.4.3.2:1
endpoint (scalar) – since 0.100
Remote endpoint IPv4/IPv6 address or a hostname, followed by a colon and a port number.
allowed-ips (sequence of scalars) – since 0.100
A list of IP (v4 or v6) addresses with CIDR masks from which this peer is allowed to send incoming
traffic and to which outgoing traffic for this peer is directed. The catch-all 0.0.0.0/0 may be
specified for matching all IPv4 addresses, and ::/0 may be specified for matching all IPv6 ad‐
dresses.
keepalive (scalar) – since 0.100
An interval in seconds, between 1 and 65535 inclusive, of how often to send an authenticated empty
packet to the peer for the purpose of keeping a stateful firewall or NAT mapping valid persistent‐
ly. Optional.
keys (mapping) – since 0.100
Define keys to use for the WireGuard peers.
This field can be used as a mapping, where you can further specify the public and shared keys.
public (scalar) – since 0.100
A base64-encoded public key, required for WireGuard peers.
shared (scalar) – since 0.100
A base64-encoded preshared key. Optional for WireGuard peers. When the systemd-networkd
backend (v242+) is used, this can also be an absolute path to a file containing the pre‐
shared key.
Properties for device type vlans:
id (scalar)
VLAN ID, a number between 0 and 4094.
link (scalar)
netplan ID of the underlying device definition on which this VLAN gets created.
Example:
ethernets:
eno1: {...}
vlans:
en-intra:
id: 1
link: eno1
dhcp4: yes
en-vpn:
id: 2
link: eno1
addresses: ...
Properties for device type nm-devices:
The nm-devices device type is for internal use only and should not be used in normal configuration files.
It enables a fallback mode for unsupported settings, using the passthrough mapping.
Backend-specific configuration parameters
In addition to the other fields available to configure interfaces, some backends may require to record
some of their own parameters in netplan, especially if the netplan definitions are generated automatical‐
ly by the consumer of that backend. Currently, this is only used with NetworkManager.
networkmanager (mapping) – since 0.99
Keeps the NetworkManager-specific configuration parameters used by the daemon to recognize connec‐
tions.
name (scalar) – since 0.99
Set the display name for the connection.
uuid (scalar) – since 0.99
Defines the UUID (unique identifier) for this connection, as generated by NetworkManager
itself.
stable-id (scalar) – since 0.99
Defines the stable ID (a different form of a connection name) used by NetworkManager in
case the name of the connection might otherwise change, such as when sharing connections
between users.
device (scalar) – since 0.99
Defines the interface name for which this connection applies.
passthrough (mapping) – since 0.102
Can be used as a fallback mechanism to missing keyfile settings.
Examples
Configure an ethernet device with networkd, identified by its name, and enable DHCP:
network:
version: 2
ethernets:
eno1:
dhcp4: true
This is an example of a static-configured interface with multiple IPv4 addresses and multiple gateways
with networkd, with equal route metric levels, and static DNS nameservers (Google DNS for this example):
network:
version: 2
renderer: networkd
ethernets:
eno1:
addresses:
- 10.0.0.10/24
- 11.0.0.11/24
nameservers:
addresses:
- 8.8.8.8
- 8.8.4.4
routes:
- to: 0.0.0.0/0
via: 10.0.0.1
metric: 100
- to: 0.0.0.0/0
via: 11.0.0.1
metric: 100
This is a complex example which shows most available features:
network:
version: 2
# if specified, can only realistically have that value, as networkd cannot
# render wifi/3G.
renderer: NetworkManager
ethernets:
# opaque ID for physical interfaces, only referred to by other stanzas
id0:
match:
macaddress: 00:11:22:33:44:55
wakeonlan: true
dhcp4: true
addresses:
- 192.168.14.2/24
- 192.168.14.3/24
- "2001:1::1/64"
nameservers:
search: [foo.local, bar.local]
addresses: [8.8.8.8]
routes:
- to: default
via: 192.168.14.1
- to: default
via: "2001:1::2"
- to: 0.0.0.0/0
via: 11.0.0.1
table: 70
on-link: true
metric: 3
routing-policy:
- to: 10.0.0.0/8
from: 192.168.14.2/24
table: 70
priority: 100
- to: 20.0.0.0/8
from: 192.168.14.3/24
table: 70
priority: 50
# only networkd can render on-link routes and routing policies
renderer: networkd
lom:
match:
driver: ixgbe
# you are responsible for setting tight enough match rules
# that only match one device if you use set-name
set-name: lom1
dhcp6: true
switchports:
# all cards on second PCI bus unconfigured by
# themselves, will be added to br0 below
match:
name: enp2*
mtu: 1280
wifis:
all-wlans:
# useful on a system where you know there is
# only ever going to be one device
match: {}
access-points:
"Joe's home":
# mode defaults to "infrastructure" (client)
password: "s3kr1t"
# this creates an AP on wlp1s0 using hostapd
# no match rules, thus the ID is the interface name
wlp1s0:
access-points:
"guest":
mode: ap
# no WPA config implies default of open
bridges:
# the key name is the name for virtual (created) interfaces
# no match: and set-name: allowed
br0:
# IDs of the components; switchports expands into multiple interfaces
interfaces: [wlp1s0, switchports]
dhcp4: true
SEE ALSO
netplan-generate(8), netplan-apply(8), netplan-try(8), netplan-get(8), netplan-set(8), netplan-dbus(8),
systemd-networkd(8), NetworkManager(8)
AUTHORS
Mathieu Trudel-Lapierre (<cyphermox@ubuntu.com>); Martin Pitt (<martin.pitt@ubuntu.com>).
netplan(5)