Provided by: libibverbs-dev_47.0-1_amd64 
NAME
mlx5dv_wr_set_mkey_sig_block - Configure a MKEY for block signature (data integrity)
operation.
SYNOPSIS
#include <infiniband/mlx5dv.h>
static inline void mlx5dv_wr_set_mkey_sig_block(struct mlx5dv_qp_ex *mqp,
const struct mlx5dv_sig_block_attr *attr)
DESCRIPTION
Configure a MKEY with block-level data protection properties. With this, the device can
add/modify/strip/validate integrity fields per block when transmitting data from memory to
network and when receiving data from network to memory.
This setter can be optionally called after a MKEY configuration work request posting has
started using mlx5dv_wr_mkey_configure(3). Configuring block signature properties to a
MKEY is done by describing what kind of signature is required (or expected) in two
domains: the wire domain and the memory domain.
The MKEY represents a virtually contiguous memory, by configuring a layout to it. The
memory signature domain describes whether data in this virtually contiguous memory
includes integrity fields, and if so, what kind and what block size.
The wire signature domain describes the same kind of properties for the data as it is seen
on the wire. Now, depending on the actual operation that happens (TX or RX), the device
will do the “right thing” based on the signature configurations of the two domains.
Example 1:
Memory signature domain is configured for CRC32 every 512B block.
Wire signature domain is configured for no signature.
A SEND is issued using the MKEY as a local key.
Result: device will gather the data with the CRC32 fields from the MKEY (using whatever
layout configured to the MKEY to locate the actual memory), validate each CRC32 against
the previous 512 bytes of data, strip the CRC32 field, and transmit only 512 bytes of data
to the wire.
Example 1.1:
Same as above, but a RECV is issued with the same key, and RX happens.
Result: device will receive the data from the wire, scatter it to the MKEY (using whatever
layout configured to the MKEY to locate the actual memory), generating and scattering
additional CRC32 field after every 512 bytes that are scattered.
Example 2:
Memory signature domain is configured for no signature.
Wire signature domain is configured for T10DIF every 4K block.
The MKEY is sent to a remote node that issues a RDMA_READ to this MKEY.
Result: device will gather the data from the MKEY (using whatever layout configured to the
MKEY to locate the actual memory), transmit it to the wire while generating an additional
T10DIF field every 4K of data.
Example 2.1:
Same as above, but remote node issues a RDMA_WRITE to this MKEY.
Result: Device will receive the data from the wire, validate each T10DIF field against the
previous 4K of data, strip the T10DIF field, and scatter the data alone to the MKEY (using
whatever layout configured to the MKEY to locate the actual memory).
ARGUMENTS
mqp
The QP where an MKEY configuration work request was created by
mlx5dv_wr_mkey_configure().
attr Block signature attributes to set for the MKEY.
Block signature attributes
Block signature attributes describe the input and output data structures in memory and
wire domains.
struct mlx5dv_sig_block_attr {
const struct mlx5dv_sig_block_domain *mem;
const struct mlx5dv_sig_block_domain *wire;
uint32_t flags;
uint8_t check_mask;
uint8_t copy_mask;
uint64_t comp_mask;
};
mem A pointer to the signature configuration for the memory domain or NULL if the
domain does not have a signature.
wire A pointer to the signature configuration for the wire domain or NULL if the domain
does not have a signature.
flags A bitwise OR of the various values described below.
MLX5DV_SIG_BLOCK_ATTR_FLAG_COPY_MASK
If the bit is not set then copy_mask is ignored. See details in the
copy_mask description.
check_mask
Each bit of check_mask corresponds to a byte of the signature field in input
domain. Byte of the input signature is checked if corresponding bit in check_mask
is set. Bits not relevant to the signature type are ignored.
Layout of check_mask.
check_mask 7 6 5 4 3 2 1 0
(bits)
─────────────────────────────────────────────────────────────────────────────────────────────────
T10-DIF (bytes) GUARD[1] GUARD[0] APP[1] APP[0] REF[3] REF[2] REF[1] REF[0]
CRC32C/CRC32 3 2 1 0
(bytes)
CRC64_XP10 7 6 5 4 3 2 1 0
(bytes)
Common used masks are defined in enum mlx5dv_sig_mask. Other masks are also
supported. Follow the above table to define a custom mask. For example, this can
be useful for the application tag field of the T10DIF signature. Using the
application tag is out of the scope of the T10DIF specification and depends on the
implementation. check_mask allows validating a part of the application tag if
needed.
copy_mask
A mask to specify what part of the signature is copied from the source domain to
the destination domain. The copy mask is usually calculated automatically. The
signature is copied if the same signature type is configurted on both domains. The
parts of the T10-DIF are compared and handled independetly.
If MLX5DV_SIG_BLOCK_ATTR_FLAG_COPY_MASK is set the copy_mask attribute overrides
the calculated value of the copy mask. Otherwise, copy_mask is ignored.
Each bit of copy_mask corresponds to a byte of the signature field. If
corresponding bit in copy_mask is set, byte of the signature is copied from the
input domain to the output domain. Calculation according to the output domain
configuration is not performed in this case. Bits not relevant to the signature
type are ignored. copy_mask may be used only if input and output domains have the
same structure, i.e. same block size and signature type. The MKEY configuration
will fail if MLX5DV_SIG_BLOCK_ATTR_FLAG_COPY_MASK is set but the domains have
different signature structures.
The predefined masks are available in enum mlx5dv_sig_mask. It is also supported
to specify a user-defined mask. Follow the table in check_mask description to
define a custom mask.
copy_mask can be useful when some bytes of the signature are not known in advance,
hence can’t be checked, but shall be preserved. In this case corresponding bits
should be cleared in check_mask and set in copy_mask.
comp_mask
Reserved for future extension, must be 0 now.
Block signature domain
struct mlx5dv_sig_block_domain {
enum mlx5dv_sig_type sig_type;
union {
const struct mlx5dv_sig_t10dif *dif;
const struct mlx5dv_sig_crc *crc;
} sig;
enum mlx5dv_block_size block_size;
uint64_t comp_mask;
};
sig_type
The signature type for this domain, one of the following
MLX5DV_SIG_TYPE_T10DIF
The block-level data protection defined in the T10 specifications (T10
SBC-3).
MLX5DV_SIG_TYPE_CRC
The block-level data protection based on cyclic redundancy check (CRC). The
specific type of CRC is defined in sig.
sig Depending on sig_type, this is the per signature type specific configuration.
block_size
The block size for this domain, one of enum mlx5dv_sig_block_size.
comp_mask
Reserved for future extension, must be 0 now.
CRC signature
struct mlx5dv_sig_crc {
enum mlx5dv_sig_crc_type type;
uint64_t seed;
};
type The specific CRC type, one of the following.
MLX5DV_SIG_CRC_TYPE_CRC32
CRC32 signature is created by calculating a 32-bit CRC defined in Fibre
Channel Physical and Signaling Interface (FC-PH), ANSI X3.230:1994.
MLX5DV_SIG_CRC_TYPE_CRC32C
CRC32C signature is created by calculating a 32-bit CRC called the
Castagnoli CRC, defined in the Internet Small Computer Systems Interface
(iSCSI) rfc3720.
MLX5DV_SIG_CRC_TYPE_CRC64_XP10
CRC64_XP10 signature is created by calculating a 64-bit CRC defined in
Microsoft XP10 compression standard.
seed A seed for the CRC calculation per block. Bits not relevant to the CRC type are
ignored. For example, all bits are used for CRC64_XP10, but only the 32 least
significant bits are used for CRC32/CRC32C.
Only the following values are supported as a seed: CRC32/CRC32C - 0,
0xFFFFFFFF(UINT32_MAX); CRC64_XP10 - 0, 0xFFFFFFFFFFFFFFFF(UINT64_MAX).
T10DIF signature
T10DIF signature is defined in the T10 specifications (T10 SBC-3) for block-level data
protection. The size of data block protected by T10DIF must be modulo 8bytes as required
in the T10DIF specifications. Note that when setting the initial LBA value to ref_tag, it
should be the value of the first block to be transmitted.
struct mlx5dv_sig_t10dif {
enum mlx5dv_sig_t10dif_bg_type bg_type;
uint16_t bg;
uint16_t app_tag;
uint32_t ref_tag;
uint16_t flags;
};
bg_type
The block guard type to be used, one of the following.
MLX5DV_SIG_T10DIF_CRC
Use CRC in the block guard field as required in the T10DIF specifications.
MLX5DV_SIG_T10DIF_CSUM
Use IP checksum instead of CRC in the block guard field.
bg A seed for the block guard calculation per block.
The following values are supported as a seed: 0, 0xFFFF(UINT16_MAX).
app_tag
An application tag to generate or validate.
ref_tag
A reference tag to generate or validate.
flags Flags for the T10DIF attributes, one of the following.
MLX5DV_SIG_T10DIF_FLAG_REF_REMAP
Increment reference tag per block.
MLX5DV_SIG_T10DIF_FLAG_APP_ESCAPE
Do not check block guard if application tag is 0xFFFF.
MLX5DV_SIG_T10DIF_FLAG_APP_REF_ESCAPE
Do not check block guard if application tag is 0xFFFF and reference tag is
0xFFFFFFFF.
RETURN VALUE
This function does not return a value.
In case of error, user will be notified later when completing the DV WRs chain.
Notes
A DEVX context should be opened by using mlx5dv_open_device(3).
MKEY must be created with MLX5DV_MKEY_INIT_ATTR_FLAGS_BLOCK_SIGNATURE flag.
The last operation posted on the supplied QP should be mlx5dv_wr_mkey_configure(3), or one
of its related setters, and the operation must still be open (no doorbell issued).
In case of ibv_wr_complete() failure or calling to ibv_wr_abort(), the MKey may be left in
an unknown state. The next configuration of it should not assume any previous state of
the MKey, i.e. signature/crypto should be re-configured or reset, as required. For
example, assuming mlx5dv_wr_set_mkey_sig_block() and then ibv_wr_abort() were called, then
on the next configuration of the MKey, if signature is not needed, it should be reset
using MLX5DV_MKEY_CONF_FLAG_RESET_SIG_ATTR.
SEE ALSO
mlx5dv_wr_mkey_configure(3), mlx5dv_create_mkey(3), mlx5dv_destroy_mkey(3)
AUTHORS
Oren Duer <oren@nvidia.com>
Sergey Gorenko <sergeygo@nvidia.com>
mlx5dv_wr_set_mkey_sig_block(3)