Provided by: runit_2.1.1-6.2ubuntu3_amd64 bug

NAME

       runsv - starts and monitors a service and optionally an appendant log service

SYNOPSIS

       runsv service

DESCRIPTION

       service must be a directory.

       runsv  switches  to  the  directory service and starts ./run.  If ./run exits and ./finish
       exists, runsv starts ./finish.   If  ./finish  doesn't  exist  or  ./finish  exits,  runsv
       restarts ./run.

       If  ./run  or  ./finish exit immediately, runsv waits a second before starting ./finish or
       restarting ./run.

       Two arguments are given to ./finish.  The first one is ./run's exit code, or -1  if  ./run
       didn't  exit normally.  The second one is the least significant byte of the exit status as
       determined by waitpid(2); for instance it is 0 if ./run exited normally,  and  the  signal
       number  if ./run was terminated by a signal.  If runsv cannot start ./run for some reason,
       the exit code is 111 and the status is 0.

       If the file service/down exists, runsv does not  start  ./run  immediately.   The  control
       interface  (see  below)  can  be  used  to start the service and to give other commands to
       runsv.

       If the directory service/log exists, runsv creates a  pipe,  redirects  service/run's  and
       service/finish's  standard  output  to the pipe, switches to the directory service/log and
       starts ./run (and ./finish) exactly as described above for  the  service  directory.   The
       standard input of the log service is redirected to read from the pipe.

       runsv  maintains  status  information  in  a binary format (compatible to the daemontools'
       supervise program) in service/supervise/status and service/log/supervise/status, and in  a
       human-readable     format     in    service/supervise/stat,    service/log/supervise/stat,
       service/supervise/pid, service/log/supervise/pid.

CONTROL

       The named pipes service/supervise/control, and (optionally)  service/log/supervise/control
       are  provided to give commands to runsv.  You can use sv(8) to control the service or just
       write one of the following characters to the named pipe:

       u      Up.  If the service is not running, start it.  If the service stops, restart it.

       d      Down.  If the service is running, send it a TERM signal, and then  a  CONT  signal.
              If  ./run  exits,  start  ./finish  if  it  exists.  After it stops, do not restart
              service.

       o      Once.  If the service is not running, start it.  Do not restart it if it stops.

       p      Pause.  If the service is running, send it a STOP signal.

       c      Continue.  If the service is running, send it a CONT signal.

       h      Hangup.  If the service is running, send it a HUP signal.

       a      Alarm.  If the service is running, send it a ALRM signal.

       i      Interrupt.  If the service is running, send it a INT signal.

       q      Quit.  If the service is running, send it a QUIT signal.

       1      User-defined 1.  If the service is running, send it a USR1 signal.

       2      User-defined 2.  If the service is running, send it a USR2 signal.

       t      Terminate.  If the service is running, send it a TERM signal.

       k      Kill.  If the service is running, send it a KILL signal.

       x      Exit.  If the service is running, send it a TERM signal, and then  a  CONT  signal.
              Do  not  restart  the  service.  If the service is down, and no log service exists,
              runsv exits.  If the service is down and a log service  exists,  runsv  closes  the
              standard  input  of  the  log  service,  and waits for it to terminate.  If the log
              service is down,  runsv  exits.   This  command  is  ignored  if  it  is  given  to
              service/log/supervise/control.

       Example: to send a TERM signal to the socklog-unix service, either do
         # sv term /etc/service/socklog-unix
        or
         # printf t >/etc/service/socklog-unix/supervise/control

       printf(1) usually blocks if no runsv process is running in the service directory.

CUSTOMIZE CONTROL

       For   each  control  character  c  sent  to  the  control  pipe,  runsv  first  checks  if
       service/control/c exists and is executable.  If so, it starts service/control/c and  waits
       for  it  to  terminate, before interpreting the command.  If the program exits with return
       code 0, runsv refrains from sending the service the corresponding signal.  The  command  o
       is  always  considered as command u.  On command d first service/control/t is checked, and
       then service/control/d.  On  command  x  first  service/control/t  is  checked,  and  then
       service/control/x.  The control of the optional log service cannot be customized.

SIGNALS

       If  runsv receives a TERM signal, it acts as if the character x was written to the control
       pipe.

EXIT CODES

       runsv exits 111 on an error on startup or if another runsv is running in service.

       runsv exits 0 if it was told to exit.

SEE ALSO

       sv(8),  chpst(8),  svlogd(8),   runit(8),   runit-init(8),   runsvdir(8),   runsvchdir(8),
       utmpset(8)

       http://smarden.org/runit/

AUTHOR

       Gerrit Pape <pape@smarden.org>

                                                                                         runsv(8)