Ubuntu Manpage: fdrawcmd - send raw commands to the floppy disk controller

Provided by: fdutils_5.5-20060227-7_amd64

Name

       fdrawcmd - send raw commands to the floppy disk controller

Note

       This  manpage  has  been  automatically  generated  from  fdutils's texinfo documentation.
       However, this process is only approximative, and some  items,  such  as  cross-references,
       footnotes  and  indices are lost in this translation process.  Indeed, these items have no
       appropriate representation in the manpage format.  Moreover, only the  items  specific  to
       each  command  have  been  translated,  and the general information about fdutils has been
       dropped in the manpage version.  Thus I strongly advise you to use  the  original  texinfo
       doc.

       *      To generate a printable copy from the texinfo doc, run the following commands:

                     ./configure; make dvi; dvips fdutils.dvi

       *      To generate a HTML copy,  run:

                     ./configure; make html

              A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils'

       *      To generate an info copy (browsable using emacs' info mode), run:

                     ./configure; make info

       The  texinfo  doc  looks most pretty when printed or as HTML.  Indeed, in the info version
       certain examples are difficult to read due to the quoting conventions used in info.

Description

          fdrawcmd [drive=drive] [rate=rate]
          [length=length] [repeat=repeat]
          [cylinder=physical-cyl] command [parameters ...] [mode]

       fdrawcmd is used to send raw commands to the floppy disk controller, after having selected
       a given drive. You must have write permission to the selected drive.

       When  writing to a disk, data is read from stdin; when reading, data is printed to stdout.
       Diagnostic messages, return values from the controller, and the value of the  disk  change
       line after the command are printed to stderr.

Options

       All numbers may be given in octal (0211), decimal (137), or hexadecimal (0x89).

       drive=drive
              Selects the drive.  The default is drive 0 (`/dev/fd0').

       rate=rate
              Selects  the data transfer rate. Use 0 for high density disks, 1 for double density
              5 1/4 disks (or 2 Mbps tapes, if the appropriate rate table is selected), and 2 for
              double density 3 1/2 disks.

       length=length
              Describes  the length of the transferred data for commands reading from and writing
              to the disk.  The default is to continue until end of file.

       repeat=count
              Repeat the command count times.  This only works correctly for commands which don't
              do any data transfer.

       cylinder=count
              Seek to the given cylinder before executing the command

       command
              The  name  of the command to send.  command may be a spelled out name (like read or
              write), or a number representing the commands floppy  disk  controller  opcode.   A
              named  command has already a mode associated with it, whereas for a number the mode
              parameter should be described using the mode option.

       parameters
              The parameters for the command (optional, not all commands need parameters).

       mode   Various flags or'ed together describing the properties of the command.

Commands

The description of the various floppy commands given in this manpage is very sketchy. For
more details get the 82078 spec sheet which can be found at:

http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/

Look for the chapter COMMAND SET/DESCRIPTIONS. Older FDCs only support a subset of the
commands described therein, but the syntax for the commands that do exist is the same.

Commands available on all FDCs
read drvsel cyl head sect szcod spt rw-gap szcod2
Reads length bytes of data from the disk. drvsel is the drive selector. Bit 0 and
1 describe the drive, and bit 2 describes the head. The remaining parameters give
the cylinder, head (yes, again), sector, size of the sector (128 * 2 ^ szcod),
sectors per track (spt, this is used to switch to the second head when the first
side has been read), and size of the read-write gap. szcod2 should be 0xff. read
returns ST0 ST1 ST2 and cyl head sect szcod of the next sector to be read; see
`/usr/include/linux/fdreg.h' .

N.B. Certain newer floppy disk controllers are buggy, and do not correctly
recognize the end of transfer when operating in virtual DMA mode. For these, you
need to set spt to the id of the last sector to be read (for example, if you intend
to read sectors 2, 3, 4, set spt to 4, even if the disk has more sectors), and set
the no-mt flag.

write drvsel cyl head sect szcod spt rw-gap szcod2
Analogous to read.

sense drvsel
Returns the third status byte (ST3)

recalibrate drvsel
Recalibrates the drive and returns ST0 ST1.

seek drvsel cyl
Moves the head to cyl and returns ST0 ST1.

specify drvsel spec1 spec2
Specify various parameters to the drive.

format drvsel szcod sect-per-track fmt-gap fmt-fill
Formats the cylinder. The new sectors are filled with fmt-fill. The header
information comes from the input, which is made up of cyl head sect szcod
quadruples. The szcod parameter from the command line is used to describe the
actual size of the sectors, and the szcod from the input is used to write into the
header. However, the first write to these sectors will use the header information,
and might overwrite the following sectors if the szcod parameter from the command
line was too small.

readid drvsel
reads the first sector header that comes and returns ST0 ST1 ST2 and cyl head sect
szcod of the encountered header.

Commands available on 82072 and later
dumpregs
Prints the contents of the FDCs registers, if supported.

Commands available on 82072A and later
configure conf1 conf2 conf3
Configures FIFO operation.

Commands available on 82077 and later
version
Echoes 0x90 if the FDC is more recent than 82072A, and 0x80 otherwise

perpendicular rate
Sets the perpendicular mode. Use 0 for normal, 2 for 500kb/s perpendicular, and 3
for 1 Mb/s perpendicular.

seek_out drvsel n
does a relative seek of n cylinders towards cylinder 0.

seek_in drvsel n
does a relative seek of n cylinders away from cylinder 0.

Commands available on 82077AA and later
lock Locks the FIFO configuration, so that it survives a FDC software reset.

unlock
Unlock the FIFO configuration

Commands available on 82078
partid
echoes a byte describing the type of the FDC in the 3 high bits, and the stepping
in the three low bits.

powerdown powerconf
configures automatic power down of the FDC. The old configuration is echoed

option iso
enables/disables ISO formats. Odd values of iso enable these formats, whereas even
values disable them. ISO formats don't have index headers, and thus allow to fit
slightly more data on a disk.

save prints out 16 internal registers of the FDC.

restore r1 r2 r3 ... r16
restores the 16 internal registers of the FDC.

format_n_write drvsel szcod sect-per-track fmt-gap fmt-fill
formats the cylinder and writes initial data to it. The input data is made up of a
sequence of headers (4 bytes) and data: header1 data1 header2 data2 ... headern
datan

drivespec dspec1 dspec2 ... specn terminator
chooses rate tables for various drives. Each dspec byte describes one drive. Bits 0
and 1 say which drive is described. Bits 2 and 3 describe the rate table. Only
tables 0 and 2 are interesting. Both tables only differ in the meaning of rate 1.
For table 0 (the default) rate 0 is 300 kb/s (used for 5 1/4 DD disks), whereas for
table 1 it is 2 Mbps (used for fast floppy tape drives). Bit 4 is the
precompensation table select bit. It should be set to 0. Bit 5-7 should be zero as
well. The terminator byte ends the drivespec command. It is either 0xc0 or 0x80. If
it is 0xc0, no result phase follows; if it is 0x80, the current data rate table
configuration for the four drives is echoed.

Modes

The mode option is only needed when you describe the command as a numerical value. Some
mode names are also valid command names. They are considered as command name if the
command name has not yet been given, and as mode name otherwise.

If you give a command name followed by explicit modes, both the implicit flags of the
command name, and the explicit modes are or'ed together.

If on the other hand you give a command name preceded by explicit modes, only the
explicit modes are or'ed together.

read Read data from disk using DMA.

write Write data to the disk.

intr Wait for an interrupt.

spin wait for the disk to spin up

disk Aborts the operation if no disk is in the drive. This only works if you also chose
a physical cylinder to seek to.

no-motor
Don't switch on the drive motor while issuing the command

no-motor-after
Switch off the motor immediately after the command returns.

fm Uses the FM version of the read, readid, write and format commands.

no-mt Do not use MT (multitrack) mode for the read, readid and write commands. This is
needed on certain broken FDC's which don't recognize end of transfer when running
in nodma mode. In order to use these safely, set no-mt, and chose the id of the
last sector to be read as sect-per-track.