NAME

       sane-artec_eplus48u - SANE backend for the scanner Artec E+ 48U and re-badged models

DESCRIPTION

       The  sane-artec_eplus48u library implements a SANE (Scanner Access Now Easy) backend that provides access
       to several USB flatbed scanners using the GT6816 chipset like the Artec E+ 48U.  These  scanners  have  a
       contact image sensor (CIS) and an USB interface.

       A       complete       list       of       supported       devices       can       be       found      on
       http://www.sane-project.org/sane-supported-devices.html.

       This is ALPHA software. Especially if you test new or untested scanners, keep your hand at the  scanner's
       plug and unplug it, if the head bumps at the end of the scan area.

       If  you  own a scanner other than the ones mentioned on the list that works with this backend, please let
       us know this by sending the scanner's exact model name and the USB vendor  and  product  ids  (e.g.  from
       /proc/bus/usb/devices,  sane-find-scanner  or  syslog) to me. Even if the scanner's name is only slightly
       different from the models mentioned above, please let me know.

KERNEL ISSUES

       If libusb-0.1.6 or later is installed, this section can be  skipped.  The  scanner  should  be  found  by
       sane-find-scanner  without  further  actions. For setting permissions and general USB information look at
       sane-usb(5).

       When you are using the scanner module, a Linux kernel 2.4.12 or newer is required.

FIRMWARE FILE

       You need a firmware file for your scanner. That's a small file containing software that will be  uploaded
       to  the  scanner's  memory. For the scanners mentioned above, it's usually named Artec48.usb or 1200.usb.
       You can find it on the installation CD that was provided by the manufacturer, normally in  the  directory
       Win98,  WinMe or similar. If the Windows-driver is installed on your computer, then you can also find the
       firmware file under c:\windows\system32\drivers.

CONFIGURATION

       The contents of the artec_eplus48u.conf file is a list of usb lines containing  vendor  and  product  ids
       that  correspond to USB scanners. The file can also contain option lines.  Empty lines and lines starting
       with a hash mark (#) are ignored.  The scanners are autodetected by usb vendor_id  product_id  statements
       which  are  already  included  into  artec_eplus48u.conf  .  "vendor_id" and "product_id" are hexadecimal
       numbers that identify the scanner.

       Every usb section can have additional options

       artecFirmwareFile @DATADIR@/sane/artec_eplus48u/Artec48.usb
              The path to the firmware file. This option is required.

       redGamma 1.0

       greenGamma 1.0

       blueGamma 1.0

       masterGamma 1.9
              These are the default gamma values. If you set the "Defaults" option with  a  frontend,  then  the
              gamma options are reset to the values specified here.

       redOffset 0x28

       greenOffset 0x2f

       blueOffset 0x2f

       redExposure 0xa7

       greenExposure 0x116

       blueExposure 0xdc
              These  are  the  default values for offset and exposure time. You can e.g. change them to speed up
              calibration, if you don't want to save the calibration data to disk.

       vendorString Artec

       modelString E+ 48U
              By default, the scanner is reported as "Artec E+ 48U". If you don't like this, e.g.   because  you
              have an Tevion MD 9693, then change the options accordingly.

FILES

       /usr/local/etc/sane.d/artec_eplus48u.conf
              The backend configuration file (see also description of SANE_CONFIG_DIR below).

       /usr/local/lib/sane/libsane-artec_eplus48u.a
              The static library implementing this backend.

       /usr/local/lib/sane/libsane-artec_eplus48u.so
              The shared library implementing this backend (present on systems that support dynamic loading).

ENVIRONMENT

       SANE_CONFIG_DIR
              This  environment  variable  specifies  the list of directories that may contain the configuration
              file.  Under UNIX, the directories are separated by a colon (`:'), under OS/2, they are  separated
              by  a  semi-colon  (`;').   If this variable is not set, the configuration file is searched in two
              default directories: first, the current working directory (".") and then in /usr/local/etc/sane.d.
              If  the  value  of  the environment variable ends with the directory separator character, then the
              default directories are searched after the explicitly specified directories.  For example, setting
              SANE_CONFIG_DIR   to   "/tmp/config:"   would   result   in  directories  "tmp/config",  ".",  and
              "/usr/local/etc/sane.d" being searched (in this order).

       SANE_DEBUG_ARTEC_EPLUS48U
              If the library was compiled with debug support enabled, this  environment  variable  controls  the
              debug level for this backend.  Higher debug levels increase the verbosity of the output.

              Example: export SANE_DEBUG_ARTEC_EPLUS48U=3

SEE ALSO

       sane(7), sane-usb(5)

AUTHOR

       Michael Herder
       This  backend  is  based  on  the gt68xx test-program written by Sergey Vlasov, Andreas Nowack, and David
       Stevenson. Thanks to everyone who tested the backend or reported bugs.
       This man page is based on man sane-gt68xx, written by Henning Meier-Geinitz.

BUGS

       This backend has been tested on Linux only. If you are using it on a different platform,  please  contact
       us.

       Interpolation with 1200 dpi is weak.

       Support for buttons is missing due to missing support in SANE.

       Please contact us if you find a bug: http://www.sane-project.org/bugs.html.

@PACKAGEVERSION@                                   11 Jul 2008                            sane-artec_eplus48u(5)