Provided by: drbd-utils_8.9.10-2ubuntu0.1_amd64 
NAME
drbdsetup - Setup tool for DRBD
SYNOPSIS
drbdsetup {device} disk {lower_dev} {meta_data_dev} {meta_data_index} [-d {size}] [-e {err_handler}]
[-f {fencing_policy}] [-b] [-t {disk_timeout}]
drbdsetup {device} net [af:] {local_addr} [:port] [af:] {remote_addr} [:port] {protocol} [-c {time}]
[-i {time}] [-t {val}] [-S {size}] [-r {size}] [-k {count}] [-e {max_epoch_size}]
[-b {max_buffers}] [-m] [-a {hash_alg}] [-x {shared_secret}] [-A {asb-0p-policy}]
[-B {asb-1p-policy}] [-C {asb-2p-policy}] [-D] [-R {role-resync-conflict-policy}]
[-p {ping_timeout}] [-u {val}] [-d {hash_alg}] [-o] [-n] [-g {congestion_policy}] [-f {val}]
[-h {val}]
drbdsetup {device} syncer [-a {dev_minor}] [-r {rate}] [-e {extents}] [-v {verify-hash-alg}]
[-c {cpu-mask}] [-C {csums-hash-alg}] [-R] [-p {plan_time}] [-s {fill_target}]
[-d {delay_target}] [-m {max_rate}] [-n {ond-policy}]
drbdsetup {device} disconnect
drbdsetup {device} detach [-f]
drbdsetup {device} down
drbdsetup {device} primary [-f] [-o]
drbdsetup {device} secondary
drbdsetup {device} verify [-s {start-position}] [-S {stop-position}]
drbdsetup {device} invalidate
drbdsetup {device} invalidate-remote
drbdsetup {device} wait-connect [-t {wfc_timeout}] [-d {degr_wfc_timeout}] [-o {outdated_wfc_timeout}]
[-w]
drbdsetup {device} wait-sync [-t {wfc_timeout}] [-d {degr_wfc_timeout}] [-o {outdated_wfc_timeout}] [-w]
drbdsetup {device} role
drbdsetup {device} cstate
drbdsetup {device} dstate
drbdsetup {device} status
drbdsetup {device} resize [-d {size}] [-f {assume-peer-has-space}] [-c {assume-clean}]
drbdsetup {device} check-resize
drbdsetup {device} pause-sync
drbdsetup {device} resume-sync
drbdsetup {device} outdate
drbdsetup {device} show-gi
drbdsetup {device} get-gi
drbdsetup {device} show
drbdsetup {device} suspend-io
drbdsetup {device} resume-io
drbdsetup {device} events [-u] [-a]
drbdsetup {device} new-current-uuid [-c]
DESCRIPTION
drbdsetup is used to associate DRBD devices with their backing block devices, to set up DRBD device pairs
to mirror their backing block devices, and to inspect the configuration of running DRBD devices.
NOTE
drbdsetup is a low level tool of the DRBD program suite. It is used by the data disk and drbd scripts to
communicate with the device driver.
COMMANDS
Each drbdsetup sub-command might require arguments and bring its own set of options. All values have
default units which might be overruled by K, M or G. These units are defined in the usual way (e.g. K =
2^10 = 1024).
Common options
All drbdsetup sub-commands accept these two options
--create-device
In case the specified DRBD device (minor number) does not exist yet, create it implicitly.
--set-defaults
When --set-defaults is given on the command line, all options of the invoked sub-command that are not
explicitly set are reset to their default values.
disk
Associates device with lower_device to store its data blocks on. The -d (or --disk-size) should only be
used if you wish not to use as much as possible from the backing block devices. If you do not use -d, the
device is only ready for use as soon as it was connected to its peer once. (See the net command.)
-d, --disk-size size
You can override DRBD's size determination method with this option. If you need to use the device
before it was ever connected to its peer, use this option to pass the size of the DRBD device to the
driver. Default unit is sectors (1s = 512 bytes).
If you use the size parameter in drbd.conf, we strongly recommend to add an explicit unit postfix.
drbdadm and drbdsetup used to have mismatching default units.
-e, --on-io-error err_handler
If the driver of the lower_device reports an error to DRBD, DRBD will mark the disk as inconsistent,
call a helper program, or detach the device from its backing storage and perform all further IO by
requesting it from the peer. The valid err_handlers are: pass_on, call-local-io-error and detach.
-f, --fencing fencing_policy
Under fencing we understand preventive measures to avoid situations where both nodes are primary and
disconnected (AKA split brain).
Valid fencing policies are:
dont-care
This is the default policy. No fencing actions are done.
resource-only
If a node becomes a disconnected primary, it tries to outdate the peer's disk. This is done by
calling the fence-peer handler. The handler is supposed to reach the other node over alternative
communication paths and call 'drbdadm outdate res' there.
resource-and-stonith
If a node becomes a disconnected primary, it freezes all its IO operations and calls its
fence-peer handler. The fence-peer handler is supposed to reach the peer over alternative
communication paths and call 'drbdadm outdate res' there. In case it cannot reach the peer, it
should stonith the peer. IO is resumed as soon as the situation is resolved. In case your handler
fails, you can resume IO with the resume-io command.
-b, --use-bmbv
In case the backing storage's driver has a merge_bvec_fn() function, DRBD has to pretend that it can
only process IO requests in units not larger than 4 KiB. (At time of writing the only known drivers
which have such a function are: md (software raid driver), dm (device mapper - LVM) and DRBD itself)
To get best performance out of DRBD on top of software raid (or any other driver with a
merge_bvec_fn() function) you might enable this option, if you know for sure that the merge_bvec_fn()
function will deliver the same results on all nodes of your cluster. I.e. the physical disks of the
software raid are exactly of the same type. USE THIS OPTION ONLY IF YOU KNOW WHAT YOU ARE DOING.
-a, --no-disk-barrier, -i, --no-disk-flushes, -D, --no-disk-drain
DRBD has four implementations to express write-after-write dependencies to its backing storage
device. DRBD will use the first method that is supported by the backing storage device and that is
not disabled by the user.
When selecting the method you should not only base your decision on the measurable performance. In
case your backing storage device has a volatile write cache (plain disks, RAID of plain disks) you
should use one of the first two. In case your backing storage device has battery-backed write cache
you may go with option 3. Option 4 (disable everything, use "none") is dangerous on most IO stacks,
may result in write-reordering, and if so, can theoretically be the reason for data corruption, or
disturb the DRBD protocol, causing spurious disconnect/reconnect cycles. Do not use no-disk-drain.
Unfortunately device mapper (LVM) might not support barriers.
The letter after "wo:" in /proc/drbd indicates with method is currently in use for a device: b, f, d,
n. The implementations:
barrier
The first requires that the driver of the backing storage device support barriers (called 'tagged
command queuing' in SCSI and 'native command queuing' in SATA speak). The use of this method can
be disabled by the --no-disk-barrier option. Note: Since Linux-2.6.36 (or RHEL's 2.6.32) this
method is disabled.
flush
The second requires that the backing device support disk flushes (called 'force unit access' in
the drive vendors speak). The use of this method can be disabled using the --no-disk-flushes
option.
drain
The third method is simply to let write requests drain before write requests of a new reordering
domain are issued. That was the only implementation before 8.0.9.
none
The fourth method is to not express write-after-write dependencies to the backing store at all,
by also specifying --no-disk-drain. This is dangerous on most IO stacks, may result in
write-reordering, and if so, can theoretically be the reason for data corruption, or disturb the
DRBD protocol, causing spurious disconnect/reconnect cycles. Do not use --no-disk-drain.
-m, --no-md-flushes
Disables the use of disk flushes and barrier BIOs when accessing the meta data device. See the notes
on --no-disk-flushes.
-s, --max-bio-bvecs
In some special circumstances the device mapper stack manages to pass BIOs to DRBD that violate the
constraints that are set forth by DRBD's merge_bvec() function and which have more than one bvec. A
known example is: phys-disk -> DRBD -> LVM -> Xen -> missaligned partition (63) -> DomU FS. Then you
might see "bio would need to, but cannot, be split:" in the Dom0's kernel log.
The best workaround is to proper align the partition within the VM (E.g. start it at sector 1024).
That costs 480 KiB of storage. Unfortunately the default of most Linux partitioning tools is to start
the first partition at an odd number (63). Therefore most distributions install helpers for virtual
linux machines will end up with missaligned partitions. The second best workaround is to limit DRBD's
max bvecs per BIO (i.e., the max-bio-bvecs option) to 1, but that might cost performance.
The default value of max-bio-bvecs is 0, which means that there is no user imposed limitation.
-t, --disk-timeout disk_timeout
If the driver of the lower_device does not finish an IO request within disk_timeout, DRBD considers
the disk as failed. If DRBD is connected to a remote host, it will reissue local pending IO requests
to the peer, and ship all new IO requests to the peer only. The disk state advances to diskless, as
soon as the backing block device has finished all IO requests.
The default value of is 0, which means that no timeout is enforced. The default unit is 100ms. This
option is available since 8.3.12.
net
Sets up the device to listen on af:local_addr:port for incoming connections and to try to connect to
af:remote_addr:port. If port is omitted, 7788 is used as default. If af is omitted ipv4 gets used. Other
supported address families are ipv6, ssocks for Dolphin Interconnect Solutions' "super sockets" and sdp
for Sockets Direct Protocol (Infiniband).
On the TCP/IP link the specified protocol is used. Valid protocol specifiers are A, B, and C.
Protocol A: write IO is reported as completed, if it has reached local disk and local TCP send buffer.
Protocol B: write IO is reported as completed, if it has reached local disk and remote buffer cache.
Protocol C: write IO is reported as completed, if it has reached both local and remote disk.
-c, --connect-int time
In case it is not possible to connect to the remote DRBD device immediately, DRBD keeps on trying to
connect. With this option you can set the time between two retries. The default value is 10 seconds,
the unit is 1 second.
-i, --ping-int time
If the TCP/IP connection linking a DRBD device pair is idle for more than time seconds, DRBD will
generate a keep-alive packet to check if its partner is still alive. The default value is 10 seconds,
the unit is 1 second.
-t, --timeout val
If the partner node fails to send an expected response packet within val tenths of a second, the
partner node is considered dead and therefore the TCP/IP connection is abandoned. The default value
is 60 (= 6 seconds).
-S, --sndbuf-size size
The socket send buffer is used to store packets sent to the secondary node, which are not yet
acknowledged (from a network point of view) by the secondary node. When using protocol A, it might be
necessary to increase the size of this data structure in order to increase asynchronicity between
primary and secondary nodes. But keep in mind that more asynchronicity is synonymous with more data
loss in the case of a primary node failure. Since 8.0.13 resp. 8.2.7 setting the size value to 0
means that the kernel should autotune this. The default size is 0, i.e. autotune.
-r, --rcvbuf-size size
Packets received from the network are stored in the socket receive buffer first. From there they are
consumed by DRBD. Before 8.3.2 the receive buffer's size was always set to the size of the socket
send buffer. Since 8.3.2 they can be tuned independently. A value of 0 means that the kernel should
autotune this. The default size is 0, i.e. autotune.
-k, --ko-count count
In case the secondary node fails to complete a single write request for count times the timeout, it
is expelled from the cluster, i.e. the primary node goes into StandAlone mode. To disable this
feature, you should explicitly set it to 0; defaults may change between versions.
-e, --max-epoch-size val
With this option the maximal number of write requests between two barriers is limited. Typically set
to the same as --max-buffers, or the allowed maximum. Values smaller than 10 can lead to degraded
performance. The default value is 2048.
-b, --max-buffers val
With this option the maximal number of buffer pages allocated by DRBD's receiver thread is limited.
Typically set to the same as --max-epoch-size. Small values could lead to degraded performance. The
default value is 2048, the minimum 32. Increase this if you cannot saturate the IO backend of the
receiving side during linear write or during resync while otherwise idle.
See also drbd.conf(5)
-u, --unplug-watermark val
This setting has no effect with recent kernels that use explicit on-stack plugging (upstream Linux
kernel 2.6.39, distributions may have backported).
When the number of pending write requests on the standby (secondary) node exceeds the
unplug-watermark, we trigger the request processing of our backing storage device. Some storage
controllers deliver better performance with small values, others deliver best performance when the
value is set to the same value as max-buffers, yet others don't feel much effect at all. Minimum 16,
default 128, maximum 131072.
-m, --allow-two-primaries
With this option set you may assign primary role to both nodes. You only should use this option if
you use a shared storage file system on top of DRBD. At the time of writing the only ones are: OCFS2
and GFS. If you use this option with any other file system, you are going to crash your nodes and to
corrupt your data!
-a, --cram-hmac-alg alg
You need to specify the HMAC algorithm to enable peer authentication at all. You are strongly
encouraged to use peer authentication. The HMAC algorithm will be used for the challenge response
authentication of the peer. You may specify any digest algorithm that is named in /proc/crypto.
-x, --shared-secret secret
The shared secret used in peer authentication. May be up to 64 characters.
-A, --after-sb-0pri asb-0p-policy
possible policies are:
disconnect
No automatic resynchronization, simply disconnect.
discard-younger-primary
Auto sync from the node that was primary before the split-brain situation occurred.
discard-older-primary
Auto sync from the node that became primary as second during the split-brain situation.
discard-zero-changes
In case one node did not write anything since the split brain became evident, sync from the node
that wrote something to the node that did not write anything. In case none wrote anything this
policy uses a random decision to perform a "resync" of 0 blocks. In case both have written
something this policy disconnects the nodes.
discard-least-changes
Auto sync from the node that touched more blocks during the split brain situation.
discard-node-NODENAME
Auto sync to the named node.
-B, --after-sb-1pri asb-1p-policy
possible policies are:
disconnect
No automatic resynchronization, simply disconnect.
consensus
Discard the version of the secondary if the outcome of the after-sb-0pri algorithm would also
destroy the current secondary's data. Otherwise disconnect.
discard-secondary
Discard the secondary's version.
call-pri-lost-after-sb
Always honor the outcome of the after-sb-0pri algorithm. In case it decides the current secondary
has the correct data, call the pri-lost-after-sb on the current primary.
violently-as0p
Always honor the outcome of the after-sb-0pri algorithm. In case it decides the current secondary
has the correct data, accept a possible instantaneous change of the primary's data.
-C, --after-sb-2pri asb-2p-policy
possible policies are:
disconnect
No automatic resynchronization, simply disconnect.
call-pri-lost-after-sb
Always honor the outcome of the after-sb-0pri algorithm. In case it decides the current secondary
has the right data, call the pri-lost-after-sb on the current primary.
violently-as0p
Always honor the outcome of the after-sb-0pri algorithm. In case it decides the current secondary
has the right data, accept a possible instantaneous change of the primary's data.
-P, --always-asbp
Normally the automatic after-split-brain policies are only used if current states of the UUIDs do not
indicate the presence of a third node.
With this option you request that the automatic after-split-brain policies are used as long as the
data sets of the nodes are somehow related. This might cause a full sync, if the UUIDs indicate the
presence of a third node. (Or double faults have led to strange UUID sets.)
-R, --rr-conflict role-resync-conflict-policy
This option sets DRBD's behavior when DRBD deduces from its meta data that a resynchronization is
needed, and the SyncTarget node is already primary. The possible settings are: disconnect,
call-pri-lost and violently. While disconnect speaks for itself, with the call-pri-lost setting the
pri-lost handler is called which is expected to either change the role of the node to secondary, or
remove the node from the cluster. The default is disconnect.
With the violently setting you allow DRBD to force a primary node into SyncTarget state. This means
that the data exposed by DRBD changes to the SyncSource's version of the data instantaneously. USE
THIS OPTION ONLY IF YOU KNOW WHAT YOU ARE DOING.
-d, --data-integrity-alg hash_alg
DRBD can ensure the data integrity of the user's data on the network by comparing hash values.
Normally this is ensured by the 16 bit checksums in the headers of TCP/IP packets. This option can be
set to any of the kernel's data digest algorithms. In a typical kernel configuration you should have
at least one of md5, sha1, and crc32c available. By default this is not enabled.
See also the notes on data integrity on the drbd.conf manpage.
-o, --no-tcp-cork
DRBD usually uses the TCP socket option TCP_CORK to hint to the network stack when it can expect more
data, and when it should flush out what it has in its send queue. There is at least one network stack
that performs worse when one uses this hinting method. Therefore we introduced this option, which
disable the setting and clearing of the TCP_CORK socket option by DRBD.
-p, --ping-timeout ping_timeout
The time the peer has to answer to a keep-alive packet. In case the peer's reply is not received
within this time period, it is considered dead. The default unit is tenths of a second, the default
value is 5 (for half a second).
-D, --discard-my-data
Use this option to manually recover from a split-brain situation. In case you do not have any
automatic after-split-brain policies selected, the nodes refuse to connect. By passing this option
you make this node a sync target immediately after successful connect.
-n, --dry-run
Causes DRBD to abort the connection process after the resync handshake, i.e. no resync gets
performed. You can find out which resync DRBD would perform by looking at the kernel's log file.
-g, --on-congestion congestion_policy, -f, --congestion-fill fill_threshold, -h, --congestion-extents
active_extents_threshold
By default DRBD blocks when the available TCP send queue becomes full. That means it will slow down
the application that generates the write requests that cause DRBD to send more data down that TCP
connection.
When DRBD is deployed with DRBD-proxy it might be more desirable that DRBD goes into AHEAD/BEHIND
mode shortly before the send queue becomes full. In AHEAD/BEHIND mode DRBD does no longer replicate
data, but still keeps the connection open.
The advantage of the AHEAD/BEHIND mode is that the application is not slowed down, even if
DRBD-proxy's buffer is not sufficient to buffer all write requests. The downside is that the peer
node falls behind, and that a resync will be necessary to bring it back into sync. During that resync
the peer node will have an inconsistent disk.
Available congestion_policys are block and pull-ahead. The default is block. Fill_threshold might be
in the range of 0 to 10GiBytes. The default is 0 which disables the check. Active_extents_threshold
has the same limits as al-extents.
The AHEAD/BEHIND mode and its settings are available since DRBD 8.3.10.
syncer
Changes the synchronization daemon parameters of device at runtime.
-r, --rate rate
To ensure smooth operation of the application on top of DRBD, it is possible to limit the bandwidth
that may be used by background synchronization. The default is 250 KiB/sec, the default unit is
KiB/sec.
-a, --after minor
Start resync on this device only if the device with minor is already in connected state. Otherwise
this device waits in SyncPause state.
-e, --al-extents extents
DRBD automatically performs hot area detection. With this parameter you control how big the hot area
(=active set) can get. Each extent marks 4M of the backing storage. In case a primary node leaves the
cluster unexpectedly, the areas covered by the active set must be resynced upon rejoining of the
failed node. The data structure is stored in the meta-data area, therefore each change of the active
set is a write operation to the meta-data device. A higher number of extents gives longer resync
times but less updates to the meta-data. The default number of extents is 127. (Minimum: 7, Maximum:
3843)
-v, --verify-alg hash-alg
During online verification (as initiated by the verify sub-command), rather than doing a bit-wise
comparison, DRBD applies a hash function to the contents of every block being verified, and compares
that hash with the peer. This option defines the hash algorithm being used for that purpose. It can
be set to any of the kernel's data digest algorithms. In a typical kernel configuration you should
have at least one of md5, sha1, and crc32c available. By default this is not enabled; you must set
this option explicitly in order to be able to use on-line device verification.
See also the notes on data integrity on the drbd.conf manpage.
-c, --cpu-mask cpu-mask
Sets the cpu-affinity-mask for DRBD's kernel threads of this device. The default value of cpu-mask is
0, which means that DRBD's kernel threads should be spread over all CPUs of the machine. This value
must be given in hexadecimal notation. If it is too big it will be truncated.
-C, --csums-alg hash-alg
A resync process sends all marked data blocks form the source to the destination node, as long as no
csums-alg is given. When one is specified the resync process exchanges hash values of all marked
blocks first, and sends only those data blocks over, that have different hash values.
This setting is useful for DRBD setups with low bandwidth links. During the restart of a crashed
primary node, all blocks covered by the activity log are marked for resync. But a large part of those
will actually be still in sync, therefore using csums-alg will lower the required bandwidth in
exchange for CPU cycles.
-R, --use-rle
During resync-handshake, the dirty-bitmaps of the nodes are exchanged and merged (using bit-or), so
the nodes will have the same understanding of which blocks are dirty. On large devices, the fine
grained dirty-bitmap can become large as well, and the bitmap exchange can take quite some time on
low-bandwidth links.
Because the bitmap typically contains compact areas where all bits are unset (clean) or set (dirty),
a simple run-length encoding scheme can considerably reduce the network traffic necessary for the
bitmap exchange.
For backward compatibilty reasons, and because on fast links this possibly does not improve transfer
time but consumes cpu cycles, this defaults to off.
Introduced in 8.3.2.
-p, --c-plan-ahead plan_time, -s, --c-fill-target fill_target, -d, --c-delay-target delay_target, -M,
--c-max-rate max_rate
The dynamic resync speed controller gets enabled with setting plan_time to a positive value. It aims
to fill the buffers along the data path with either a constant amount of data fill_target, or aims to
have a constant delay time of delay_target along the path. The controller has an upper bound of
max_rate.
By plan_time the agility of the controller is configured. Higher values yield for slower/lower
responses of the controller to deviation from the target value. It should be at least 5 times RTT.
For regular data paths a fill_target in the area of 4k to 100k is appropriate. For a setup that
contains drbd-proxy it is advisable to use delay_target instead. Only when fill_target is set to 0
the controller will use delay_target. 5 times RTT is a reasonable starting value. Max_rate should be
set to the bandwidth available between the DRBD-hosts and the machines hosting DRBD-proxy, or to the
available disk-bandwidth.
The default value of plan_time is 0, the default unit is 0.1 seconds. Fill_target has 0 and sectors
as default unit. Delay_target has 1 (100ms) and 0.1 as default unit. Max_rate has 10240 (100MiB/s)
and KiB/s as default unit.
-m, --c-min-rate min_rate
We track the disk IO rate caused by the resync, so we can detect non-resync IO on the lower level
device. If the lower level device seems to be busy, and the current resync rate is above min_rate, we
throttle the resync.
The default value of min_rate is 4M, the default unit is k. If you want to not throttle at all, set
it to zero, if you want to throttle always, set it to one.
-n, --on-no-data-accessible ond-policy
This setting controls what happens to IO requests on a degraded, disk less node (I.e. no data store
is reachable). The available policies are io-error and suspend-io.
If ond-policy is set to suspend-io you can either resume IO by attaching/connecting the last lost
data storage, or by the drbdadm resume-io res command. The latter will result in IO errors of course.
The default is io-error. This setting is available since DRBD 8.3.9.
primary
Sets the device into primary role. This means that applications (e.g. a file system) may open the device
for read and write access. Data written to the device in primary role are mirrored to the device in
secondary role.
Normally it is not possible to set both devices of a connected DRBD device pair to primary role. By using
the --allow-two-primaries option, you override this behavior and instruct DRBD to allow two primaries.
-o, --overwrite-data-of-peer
Alias for --force.
-f, --force
Becoming primary fails if the local replica is not up-to-date. I.e. when it is inconsistent, outdated
of consistent. By using this option you can force it into primary role anyway. USE THIS OPTION ONLY
IF YOU KNOW WHAT YOU ARE DOING.
secondary
Brings the device into secondary role. This operation fails as long as at least one application (or file
system) has opened the device.
It is possible that both devices of a connected DRBD device pair are secondary.
verify
This initiates on-line device verification. During on-line verification, the contents of every block on
the local node are compared to those on the peer node. Device verification progress can be monitored via
/proc/drbd. Any blocks whose content differs from that of the corresponding block on the peer node will
be marked out-of-sync in DRBD's on-disk bitmap; they are not brought back in sync automatically. To do
that, simply disconnect and reconnect the resource.
If on-line verification is already in progress (and this node is "VerifyS"), this command silently
"succeeds". In this case, any start-sector (see below) will be ignored, and any stop-sector (see below)
will be honored. This can be used to stop a running verify, or to update/shorten/extend the coverage of
the currently running verify.
This command will fail if the device is not part of a connected device pair.
See also the notes on data integrity on the drbd.conf manpage.
-s, --start start-sector
Since version 8.3.2, on-line verification should resume from the last position after connection loss.
It may also be started from an arbitrary position by setting this option. If you had reached some
stop-sector before, and you do not specify an explicit start-sector, verify should resume from the
previous stop-sector.
Default unit is sectors. You may also specify a unit explicitly. The start-sector will be rounded
down to a multiple of 8 sectors (4kB).
-S, --stop stop-sector
Since version 8.3.14, on-line verification can be stopped before it reaches end-of-device. This can
be
Default unit is sectors. You may also specify a unit explicitly. The stop-sector may be updated by
issuing an additional drbdsetup verify command on the same node while the verify is running.
invalidate
This forces the local device of a pair of connected DRBD devices into SyncTarget state, which means that
all data blocks of the device are copied over from the peer.
This command will fail if the device is not either part of a connected device pair, or disconnected
Secondary.
invalidate-remote
This forces the local device of a pair of connected DRBD devices into SyncSource state, which means that
all data blocks of the device are copied to the peer.
On a disconnected Primary device, this will set all bits in the out of sync bitmap. As a side affect this
suspends updates to the on disk activity log. Updates to the on disk activity log resume automatically
when necessary.
wait-connect
Returns as soon as the device can communicate with its partner device.
-t, --wfc-timeout wfc_timeout, -d, --degr-wfc-timeout degr_wfc_timeout, -o, --outdated-wfc-timeout
outdated_wfc_timeout, -w, --wait-after-sb
This command will fail if the device cannot communicate with its partner for timeout seconds. If the
peer was working before this node was rebooted, the wfc_timeout is used. If the peer was already down
before this node was rebooted, the degr_wfc_timeout is used. If the peer was sucessfully outdated
before this node was rebooted the outdated_wfc_timeout is used. The default value for all those
timeout values is 0 which means to wait forever. In case the connection status goes down to
StandAlone because the peer appeared but the devices had a split brain situation, the default for the
command is to terminate. You can change this behavior with the --wait-after-sb option.
wait-sync
Returns as soon as the device leaves any synchronization into connected state. The options are the same
as with the wait-connect command.
disconnect
Removes the information set by the net command from the device. This means that the device goes into
unconnected state and will no longer listen for incoming connections.
detach
Removes the information set by the disk command from the device. This means that the device is detached
from its backing storage device.
-f, --force
A regular detach returns after the disk state finally reached diskless. As a consequence detaching
from a frozen backing block device never terminates.
On the other hand A forced detach returns immediately. It allows you to detach DRBD from a frozen
backing block device. Please note that the disk will be marked as failed until all pending IO
requests where finished by the backing block device.
down
Removes all configuration information from the device and forces it back to unconfigured state.
role
Shows the current roles of the device and its peer, as local/peer.
state
Deprecated alias for "role"
cstate
Shows the current connection state of the device.
dstate
Shows the current states of the backing storage devices, as local/peer.
status
Shows the current status of the device in XML-like format. Example output:
<resource minor="0" name="s0" cs="SyncTarget" st1="Secondary" st2="Secondary"
ds1="Inconsistent" ds2="UpToDate" resynced_precent="5.9" />
resize
This causes DRBD to reexamine the size of the device's backing storage device. To actually do online
growing you need to extend the backing storages on both devices and call the resize command on one of
your nodes.
The --assume-peer-has-space allows you to resize a device which is currently not connected to the peer.
Use with care, since if you do not resize the peer's disk as well, further connect attempts of the two
will fail.
When the --assume-clean option is given DRBD will skip the resync of the new storage. Only do this if you
know that the new storage was initialized to the same content by other means.
check-resize
To enable DRBD to detect offline resizing of backing devices this command may be used to record the
current size of backing devices. The size is stored in files in /var/lib/drbd/ named drbd-minor-??.lkbd
This command is called by drbdadm resize res after drbdsetup device resize returned.
pause-sync
Temporarily suspend an ongoing resynchronization by setting the local pause flag. Resync only progresses
if neither the local nor the remote pause flag is set. It might be desirable to postpone DRBD's
resynchronization after eventual resynchronization of the backing storage's RAID setup.
resume-sync
Unset the local sync pause flag.
outdate
Mark the data on the local backing storage as outdated. An outdated device refuses to become primary.
This is used in conjunction with fencing and by the peer's fence-peer handler.
show-gi
Displays the device's data generation identifiers verbosely.
get-gi
Displays the device's data generation identifiers.
show
Shows all available configuration information of the device.
suspend-io
This command is of no apparent use and just provided for the sake of completeness.
resume-io
If the fence-peer handler fails to stonith the peer node, and your fencing policy is set to
resource-and-stonith, you can unfreeze IO operations with this command.
events
Displays every state change of DRBD and all calls to helper programs. This might be used to get notified
of DRBD's state changes by piping the output to another program.
-a, --all-devices
Display the events of all DRBD minors.
-u, --unfiltered
This is a debugging aid that displays the content of all received netlink messages.
new-current-uuid
Generates a new current UUID and rotates all other UUID values. This has at least two use cases, namely
to skip the initial sync, and to reduce network bandwidth when starting in a single node configuration
and then later (re-)integrating a remote site.
Available option:
-c, --clear-bitmap
Clears the sync bitmap in addition to generating a new current UUID.
This can be used to skip the initial sync, if you want to start from scratch. This use-case does only
work on "Just Created" meta data. Necessary steps:
1. On both nodes, initialize meta data and configure the device.
drbdadm -- --force create-md res
2. They need to do the initial handshake, so they know their sizes.
drbdadm up res
3. They are now Connected Secondary/Secondary Inconsistent/Inconsistent. Generate a new current-uuid and
clear the dirty bitmap.
drbdadm -- --clear-bitmap new-current-uuid res
4. They are now Connected Secondary/Secondary UpToDate/UpToDate. Make one side primary and create a file
system.
drbdadm primary res
mkfs -t fs-type $(drbdadm sh-dev res)
One obvious side-effect is that the replica is full of old garbage (unless you made them identical using
other means), so any online-verify is expected to find any number of out-of-sync blocks.
You must not use this on pre-existing data! Even though it may appear to work at first glance, once you
switch to the other node, your data is toast, as it never got replicated. So do not leave out the mkfs
(or equivalent).
This can also be used to shorten the initial resync of a cluster where the second node is added after the
first node is gone into production, by means of disk shipping. This use-case works on disconnected
devices only, the device may be in primary or secondary role.
The necessary steps on the current active server are:
1. drbdsetup device new-current-uuid --clear-bitmap
2. Take the copy of the current active server. E.g. by pulling a disk out of the RAID1 controller, or by
copying with dd. You need to copy the actual data, and the meta data.
3. drbdsetup device new-current-uuid
Now add the disk to the new secondary node, and join it to the cluster. You will get a resync of that
parts that were changed since the first call to drbdsetup in step 1.
EXAMPLES
For examples, please have a look at the DRBD User's Guide[1].
VERSION
This document was revised for version 8.3.2 of the DRBD distribution.
AUTHOR
Written by Philipp Reisner <philipp.reisner@linbit.com> and Lars Ellenberg <lars.ellenberg@linbit.com>
REPORTING BUGS
Report bugs to <drbd-user@lists.linbit.com>.
COPYRIGHT
Copyright 2001-2008 LINBIT Information Technologies, Philipp Reisner, Lars Ellenberg. This is free
software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
drbd.conf(5), drbd(8), drbddisk(8), drbdadm(8), DRBD User's Guide[1], DRBD web site[2]
NOTES
1. DRBD User's Guide
http://www.drbd.org/users-guide/
2. DRBD web site
http://www.drbd.org/