Provided by: reconserver_0.15.2-1build1_amd64 
NAME
reConServer - reConServer SIP conferencing server
SYNOPSIS
reConServer [OPTIONS...]
DESCRIPTION
reConServer is an open-source, free SIP conferencing server. SIP is changing the way people communicate
using the Internet. It is not only about making phone calls over the Net. The SIP protocol and its
extensions defines the way of establishing, modifying and ending interactive sessions, no matter if they
are voice, video, IM or a combination of them. At the heart of SIP architecture, there are certain
services which needs to be provided at some place of the network. reConServer provides SIP conferencing
services. These services enable audio conferencing between multiple participants.
OPTIONS
-l, --log-type=cout|syslog|cerr
Set where to send logging messages. The default cout sends the messages to standard output, cerr
uses the standard error pipe. With syslog the messages are send to the system log using the
logging facility local6. See syslogd(8) or syslog.conf(5) for more information.
-v, --log-level=STACK|DEBUG|INFO|WARNING|ALERT
Set the minimum level a logging message needs to have in order to by written. The severity rises
from left to right in the above order. The default is to log messages with level INFO or above.
-r, --record-route=sip:example.com
Activate record routing. The argument is the URI used in the Record-Route header field.
--udp=5060
Specify the port to use for the UDP transport. Set to 0 to turn UDP off. Defaults to port 5060.
--tcp=5060
Specify the port to use for the TCP transport. Set to 0 to turn TCP off. Defaults to port 5060.
-t, --tls-domain=example.com
Act as a TLS server for specified domain.
--tls=5061
Set the port to use for the TLS transport. Set to 0 to turn TLS off. Defaults to port 5061.
--dtls=0
Set the port to use for the DTLS transport. Set to 0 to turn DTLS off which is the default.
--enable-cert-server
Run a cert server.
-c, --cert-path=STRING
Set the path for certificates. Defaults to ~/.sipCerts.
--enable-v6
Enable IPv6.
--disable-v4
Disable IPv4.
--disable-auth
Disable DIGEST challenges for certain SIP requests.
--disable-web-auth
Disable authentication for the web administration server.
--disable-reg
Disable the registrar.
-i, --interfaces=sip:10.1.1.1:5065;transport=tls
Specify interfaces to add transports to. Each transport is given as a SIP-URI with the IP address
and port of the local interface as the hostport part and the transport protocol as a transport
parameter. Several transports are separated by a comma.
For example, to set up two transports, one for TLS and one for UDP use
sip:192.168.1.200:5060;transport=tls,sip:192.168.1.200:5060;transport=udp
-d, --domains=example.com,foo.com
Specify the list of domains this proxy is authorative for separated by comma.
-R, --route=sip:p1.example.com,sip:p2.example.com
Specify a route set where all requests this proxy is authorative for are sent to. Using this
option overides the routes set through the web interface.
--reqChainName=STRING
Name of request chain used for processing requests. Currently, the only chain available is
default.
--http=5080
Specify the port used by the HTTP server. Defaults to 5080.
--recursive-redirect
Enable to handle of 3xx responses in the proxy.
--q-value
Enable q-value processing. The q-value can be given in registrations and is used by the location
server to order forwarding for multiple registrations. Without this option a request is forked to
all registrations.
--q-value-behavior=FULL_SEQUENTIAL|EQUAL_Q_PARALLEL|FULL_PARALLEL
Specify forking behavior if --q-value is given. With FULL_SEQUENTIAL one target is called after
another in the order of their q values. Using EQUAL_Q_PARALLEL (the default), the request is sent
in batches of all registrations with the same q value. The batches are again ordered by the q
value. FULL_PARALLEL causes the request to be sent in parallel to all registrations.
--q-value-cancel-btw-fork-groups
If given, groups of parallel forks are canceled after the period specified by the
--q-value-ms-before-cancel option if no response was received.
--q-value-wait-for-terminate-btw-fork-groups
If given, the proxy waits for groups of parallel forks to terminate before a new group is started.
Otherwise, the next group is started once the waiting time has passed.
--q-value-ms-between-fork-groups=INT
Specify the number of milliseconds to wait for a response from a group of parallel forks before
starting another group.
--q-value-ms-before-cancel=INT
Specify the number of milliseconds to wait before cancelling a group of parallel forks if the
--q-value-cancel-btw-fork-groups option is given.
-e, --enum-suffix=e164.arpa
Specify enum suffix to search.
-b, --allow-bad-reg
Allow To tag in registrations.
--timer-C=180
Specify the length of timer C in sec which specifies the time a proxy waits before generating a
timeout response. Set to 0 or a negative value to turn timer C of completely.
--admin-password=STRING
Set the web administrator password.
Help options:
-?, --help
Show a help message.
--usage
Display brief usage message.
--version
Display the version information.
SEE ALSO
Repro web site at https://https://github.com/resiprocate/reConServer
August 2013 reConServer(8)