Provided by: firewalld_0.8.2-1_all bug

NAME

       firewalld.conf - firewalld configuration file

SYNOPSIS

       /etc/firewalld/firewalld.conf

DESCRIPTION

       firewalld.conf is loaded by firewalld during the initialization process. The file contains
       the basic configuration options for firewalld.

OPTIONS

       These are the options that can be set in the config file:

       DefaultZone
           This sets the default zone for connections or interfaces if the zone is not selected
           or specified by NetworkManager, initscripts or command line tool. The default zone is
           public.

       MinimalMark
           Deprecated. This option is ignored and no longer used. Marks are no longer used
           internally.

       CleanupOnExit
           If firewalld stops, it cleans up all firewall rules. Setting this option to no or
           false leaves the current firewall rules untouched. The default value is yes or true.

       Lockdown
           If this option is enabled, firewall changes with the D-Bus interface will be limited
           to applications that are listed in the lockdown whitelist (see firewalld.lockdown-
           whitelist(5)). The default value is no or false.

       IPv6_rpfilter
           If this option is enabled (it is by default), reverse path filter test on a packet for
           IPv6 is performed. If a reply to the packet would be sent via the same interface that
           the packet arrived on, the packet will match and be accepted, otherwise dropped. For
           IPv4 the rp_filter is controlled using sysctl.

       IndividualCalls
           If this option is disabled (it is by default), combined -restore calls are used and
           not individual calls to apply changes to the firewall. The use of individiual calls
           increases the time that is needed to apply changes and to start the daemon, but is
           good for debugging as error messages are more specific.

       LogDenied
           Add logging rules right before reject and drop rules in the INPUT, FORWARD and OUTPUT
           chains for the default rules and also final reject and drop rules in zones for the
           configured link-layer packet type. The possible values are: all, unicast, broadcast,
           multicast and off. The default setting is off, which disables the logging.

       AutomaticHelpers
           Deprecated. This option is ignored and no longer used.

       FirewallBackend
           Selects the firewall backend implementation. Possible values are; nftables (default),
           or iptables. This applies to all firewalld primitives. The only exception is direct
           and passthrough rules which always use the traditional iptables, ip6tables, and
           ebtables backends.

       FlushAllOnReload
           Flush all runtime rules on a reload. In previous releases some runtime configuration
           was retained during a reload, namely; interface to zone assignment, and direct rules.
           This was confusing to users. To get the old behavior set this to "no". Defaults to
           "yes".

       RFC3964_IPv4
           As per RFC 3964, filter IPv6 traffic with 6to4 destination addresses that correspond
           to IPv4 addresses that should not be routed over the public internet. Defaults to
           "yes".

       AllowZoneDrifting
           Older versions of firewalld had undocumented behavior known as "zone drifting". This
           allowed packets to ingress multiple zones - this is a violation of zone based
           firewalls. However, some users rely on this behavior to have a "catch-all" zone, e.g.
           the default zone. You can enable this if you desire such behavior. It's disabled by
           default for security reasons. Note: If "yes" packets will only drift from source based
           zones to interface based zones (including the default zone). Packets never drift from
           interface based zones to other interfaces based zones (including the default zone).
           Valid values; "yes", "no". Defaults to "no".

SEE ALSO

       firewall-applet(1), firewalld(1), firewall-cmd(1), firewall-config(1), firewalld.conf(5),
       firewalld.direct(5), firewalld.dbus(5), firewalld.icmptype(5), firewalld.lockdown-
       whitelist(5), firewall-offline-cmd(1), firewalld.richlanguage(5), firewalld.service(5),
       firewalld.zone(5), firewalld.zones(5), firewalld.ipset(5), firewalld.helper(5)

NOTES

       firewalld home page:
           http://firewalld.org

       More documentation with examples:
           http://fedoraproject.org/wiki/FirewallD

AUTHORS

       Thomas Woerner <twoerner@redhat.com>
           Developer

       Jiri Popelka <jpopelka@redhat.com>
           Developer

       Eric Garver <eric@garver.life>
           Developer