Ubuntu Manpage: cgroup.conf - Slurm configuration file for the cgroup support

Provided by: slurm-client_19.05.5-1_amd64

NAME

       cgroup.conf - Slurm configuration file for the cgroup support

DESCRIPTION

cgroup.conf is an ASCII file which defines parameters used by Slurm's Linux cgroup related plugins. The
file location can be modified at system build time using the DEFAULT_SLURM_CONF parameter or at execution
time by setting the SLURM_CONF environment variable. The file will always be located in the same
directory as the slurm.conf file.

Parameter names are case insensitive. Any text following a "#" in the configuration file is treated as a
comment through the end of that line. Changes to the configuration file take effect upon restart of
Slurm daemons, daemon receipt of the SIGHUP signal, or execution of the command "scontrol reconfigure"
unless otherwise noted.

For general Slurm Cgroups information, see the Cgroups Guide at <https://slurm.schedmd.com/cgroups.html>.

The following cgroup.conf parameters are defined to control the general behavior of Slurm cgroup plugins.

CgroupAutomount=<yes|no>
Slurm cgroup plugins require valid and functional cgroup subsystem to be mounted under
/sys/fs/cgroup/<subsystem_name>. When launched, plugins check their subsystem availability. If
not available, the plugin launch fails unless CgroupAutomount is set to yes. In that case, the
plugin will first try to mount the required subsystems.

CgroupMountpoint=PATH
Specify the PATH under which cgroups should be mounted. This should be a writable directory which
will contain cgroups mounted one per subsystem. The default PATH is /sys/fs/cgroup.

TASK/CGROUP PLUGIN

The following cgroup.conf parameters are defined to control the behavior of this particular plugin:

AllowedKmemSpace=<number>
Constrain the job cgroup kernel memory to this amount of the allocated memory, specified in bytes.
The AllowedKmemSpace must be between the upper and lower memory limits, specified by
MaxKmemPercent and MinKmemSpace, respectively. If AllowedKmemSpace goes beyond the upper or lower
limit, it will be reset to that upper or lower limit, whichever has been exceeded.

AllowedRAMSpace=<number>
Constrain the job/step cgroup RAM to this percentage of the allocated memory. The percentage
supplied may be expressed as floating point number, e.g. 101.5. Sets the cgroup soft memory limit
at the allocated memory size and then sets the job/step hard memory limit at the
(AllowedRAMSpace/100) * allocated memory. If the job/step exceeds the hard limit, then it might
trigger Out Of Memory (OOM) events (including oom-kill) which will be logged to kernel log
ringbuffer (dmesg in Linux). Setting AllowedRAMSpace above 100 may cause system Out of Memory
(OOM) events as it allows job/step to allocate more memory than configured to the nodes. Reducing
configured node available memory to avoid system OOM events is suggested. Setting AllowedRAMSpace
below 100 will result in jobs receiving less memory than allocated and soft memory limit will set
to the same value as the hard limit. Also see ConstrainRAMSpace. The default value is 100.

AllowedSwapSpace=<number>
Constrain the job cgroup swap space to this percentage of the allocated memory. The default value
is 0, which means that RAM+Swap will be limited to AllowedRAMSpace. The supplied percentage may be
expressed as a floating point number, e.g. 50.5. If the limit is exceeded, the job steps will be
killed and a warning message will be written to standard error. Also see ConstrainSwapSpace.
NOTE: Setting AllowedSwapSpace to 0 does not restrict the Linux kernel from using swap space. To
control how the kernel uses swap space, see MemorySwappiness.

ConstrainCores=<yes|no>
If configured to "yes" then constrain allowed cores to the subset of allocated resources. This
functionality makes use of the cpuset subsystem. Due to a bug fixed in version 1.11.5 of HWLOC,
the task/affinity plugin may be required in addition to task/cgroup for this to function properly.
The default value is "no".

ConstrainDevices=<yes|no>
If configured to "yes" then constrain the job's allowed devices based on GRES allocated resources.
It uses the devices subsystem for that. The default value is "no".

ConstrainKmemSpace=<yes|no>
If configured to "yes" then constrain the job's Kmem RAM usage in addition to RAM usage. Only
takes effect if ConstrainRAMSpace is set to "yes". The default value is "no". If set to yes, the
job's Kmem limit will be set to AllowedKmemSpace if set; otherwise, the job's Kmem limit will be
set to its RAM limit. Also see AllowedKmemSpace.

ConstrainRAMSpace=<yes|no>
If configured to "yes" then constrain the job's RAM usage by setting the memory soft limit to the
allocated memory and the hard limit to the allocated memory * AllowedRAMSpace. The default value
is "no", in which case the job's RAM limit will be set to its swap space limit if
ConstrainSwapSpace is set to "yes". Also see AllowedSwapSpace, AllowedRAMSpace and
ConstrainSwapSpace. NOTE: When enabled, ConstrainRAMSpace can lead to a noticeable decline in
per-node job throughout. Sites with high-throughput requirements should carefully weigh the
tradeoff between per-node throughput, versus potential problems that can arise from unconstrained
memory usage on the node. See <https://slurm.schedmd.com/high_throughput.html> for further
discussion.

ConstrainSwapSpace=<yes|no>
If configured to "yes" then constrain the job's swap space usage. The default value is "no". Note
that when set to "yes" and ConstrainRAMSpace is set to "no", AllowedRAMSpace is automatically set
to 100% in order to limit the RAM+Swap amount to 100% of job's requirement plus the percent of
allowed swap space. This amount is thus set to both RAM and RAM+Swap limits. This means that in
that particular case, ConstrainRAMSpace is automatically enabled with the same limit than the one
used to constrain swap space. Also see AllowedSwapSpace.

MaxRAMPercent=PERCENT
Set an upper bound in percent of total RAM on the RAM constraint for a job. This will be the
memory constraint applied to jobs that are not explicitly allocated memory by Slurm (i.e. Slurm's
select plugin is not configured to manage memory allocations). The PERCENT may be an arbitrary
floating point number. The default value is 100.

MaxSwapPercent=PERCENT
Set an upper bound (in percent of total RAM) on the amount of RAM+Swap that may be used for a job.
This will be the swap limit applied to jobs on systems where memory is not being explicitly
allocated to job. The PERCENT may be an arbitrary floating point number between 0 and 100. The
default value is 100.

MaxKmemPercent=PERCENT
Set an upper bound in percent of total Kmem for a job. The PERCENT may be an arbitrary floating
point number. The default value is 100.

MemorySwappiness=<number>
Configure the kernel's priority for swapping out anonymous pages (such as program data) verses
file cache pages for the job cgroup. Valid values are between 0 and 100, inclusive. A value of 0
prevents the kernel from swapping out program data. A value of 100 gives equal priorioty to
swapping out file cache or anonymous pages. If not set, then the kernel's default swappiness value
will be used. Either ConstrainRAMSpace or ConstrainSwapSpace must be set to yes in order for this
parameter to be applied.

MinKmemSpace=<number>
Set a lower bound (in MB) on the memory limits defined by AllowedKmemSpace. The default limit is
30M.

MinRAMSpace=<number>
Set a lower bound (in MB) on the memory limits defined by AllowedRAMSpace and AllowedSwapSpace.
This prevents accidentally creating a memory cgroup with such a low limit that slurmstepd is
immediately killed due to lack of RAM. The default limit is 30M.

TaskAffinity=<yes|no>
If configured to "yes" then set a default task affinity to bind each step task to a subset of the
allocated cores using sched_setaffinity. The default value is "no". Note: This feature requires
the Portable Hardware Locality (hwloc) library to be installed.

DISTRIBUTION-SPECIFIC NOTES

       Debian and derivatives (e.g. Ubuntu) usually exclude the memory and memsw (swap) cgroups by  default.  To
       include them, add the following parameters to the kernel command line: cgroup_enable=memory swapaccount=1

       This can usually be placed in /etc/default/grub inside the GRUB_CMDLINE_LINUX variable. A command such as
       update-grub must be run after updating the file.

EXAMPLE

       ###
       # Slurm cgroup support configuration file
       ###
       CgroupAutomount=yes
       ConstrainCores=yes
       #

COPYING