Provided by: liblopsub-dev_1.0.3-2_amd64 
NAME
lopsub-suite - lopsub suite syntax
DESCRIPTION
A lopsub suite describes the options to a command line utility with zero or more related
subcommands. The lopsubgen(1) utility translates a lopsub suite into either C source code
or a manual page. The generated C code can be compiled and linked against the lopsub
library to produce command line parsers for the main command and all subcommands defined
in the suite.
This document explains the format of a lopsub suite. The overall structure is as follows:
[suite mysuite]
suite directives
[supercommand sup_cmd]
command directives for sup_cmd
[option opt1]
... (further options)
[subcommand sub1]
command directives for sub1
[option opt_1_to_sub1]
option directives for opt_1
... (further options)
... (further subcommands)
[section see also]
... (optional extra section for man page)
... (further extra sections)
A suite begins with a [suite] line which declares the name of the suite. The suite
directives, all subsequent lines up to the first [supercommand] or [subcommand] line,
state further properties of the suite which are unrelated to any particular command, for
example the version number. All available suite directives are summarized below.
The [supercommand] and [subcommand] lines indicate the beginning of a command of the
suite. The part between this line and the first [option] line contains the command
directives, for example the purpose and the description of the named command. See the
section on command directives below.
Supercommands and subcommands share the same set of possible command directives. They
differ mainly in the way the documentation is formated. There can only be one supercommand
but arbitrary many subcommands. For example, the supercommand could be the name of the
application, and the subcommands could be "load", "save" "info" and "quit". The subcommand
would be passed as the first non-option argument to the supercommand, followed by options
specific to that subcommand.
Of course it is possible to define no subcommands at all. Conversely, one can define only
subcommands but no supercommand. This makes sense if the commands are run by some other
means, for example in an interactive session from a command prompt.
Within the command section, an [option] line starts an option to the current command. It
is followed by option directives, which specify, for example, whether or not the option
takes an argument. All supported option directives are listed in the corresponding section
below.
Further material for man output can be included between the [section] and [/section]
markers. This text will not be included in the generated .c and .h files and is thus also
not part of the short and long help available at run time. The text is not interpreted
except that leading whitespace is stripped from each line. Arbitrary roff source can be
included here.
Empty lines and lines starting with a hash character (#) are ignored.
SUITE DIRECTIVES
Most directives of this section are only relevant for man page output (with
aux_info_default being the exception), they are ignored for C output.
caption
The optional text for an unnumbered section heading at the beginning of the manual
page.
title Sets the title of the man page. Defaults to the name of the supercommand. If this
is not given and the suite has no supercommand, the .TH macro to set the title of
the man page is omitted.
mansect
Sets the man page section. Defaults to 1 (user commands). Both title and section
are positioned at the left and right in the header line.
date This text is positioned in the middle of the footer line of the man page. It is
common to set this to the date of the last nontrivial change that was made to the
man page. Defaults to the current date.
version-string
Positioned at the left in the footer line. Defaults to the empty string. The value
of this directive is ignored if a version string is explicitly requested by passing
--version-string to losubgen.
manual_title
Centered in the header line. Defaults to "User commands".
introduction
conclusion
The text enclosed between [introduction] and [/introduction] is shown between the
supercommand (if any) and the subcommand list. Concluding remarks after the
subcommand list may be added in the same way with [conclusion] and [/conclusion].
Both texts will become part of the manual page, but are not not part of the short
or long help. Like for the section directive, arbitrary roff source may be included
here.
aux_info_prefix
This text is shown at the bottom of each command before the value of the aux_info
directive. If no aux_info is specified for a command, the prefix is omitted as
well. If aux_info_prefix is not given, the empty string is assumed.
aux_info_default
This text is only used for header output. The argument for the generated macro
call is set to this value for all commands for which no aux_info directive is
given. If no aux_info_default directive is given, the value 0 is used as the
argument for the macro.
COMMAND DIRECTIVES
purpose
A single line containing the purpose of the command. This text is printed in the
short and long help, and is also included in the man page.
description
closing
Arbitrary plain text enclosed between [description] and [/description]. The text
may be split over multiple lines and paragraphs. The description of the
supercommand (if any) becomes the description of the manual page, which is shown
after the command summary and before the list of options. The descriptions of all
commands are included in the manual page and in the long help text but not in the
short help.
Closing remarks for the command can be added in a similar way by enclosing plain
text between [closing] and [/closing]. This text will be positioned after the
option list.
synopsis
Custom synopsis of the command. If this is not given, the synopsis text will be
auto-generated from the options and the value of the non-opts-name directive.
non-opts-name
Name of the command line arguments which are not related to any option, for example
file names. This text will be included in the automatically generated synopsis
text.
If this is not given, the command is assumed to take no arguments other than the
specified options and their arguments. For such commands the attempt to parse an
argv[] vector fails if it contains further non-option arguments.
aux_info
This directive is special because its value is not included in the generated .c
file but in the header file. More precisely, the preprocessor macro
LSG_SUITENAME_AUX_INFOS will be defined which expands to a series of macro calls to
LSG_SUITENAME_AUX_INFO(val_n), one for each command of the suite, where val_n is
the (unquoted) value of the aux_info directive of the nth command. Commands for
which no aux_info directive was specified receive a value of zero. The
LSG_SUITENAME_AUX_INFO macro is supposed to be defined by the application. Hence
it is up to the application to make the expansion of LSG_SUITENAME_AUX_INFOS a
valid C construct.
The value, if specified, is also copied to the man page at the end of the section
for the command.
OPTION DIRECTIVES
short_opt
The optional single-letter equivalent for the option. If this is specified, the
option may be given either in the GNU-style long option format with two leading
dashes or in the short form with a single dash. Otherwise only the long form will
be accepted. As usual, multiple short option flags may be combined.
summary
A single line which summarizes the option. This text is included in both the short
and the long help and in the man page. Defaults to the empty string.
typestr
A description for the type of the values for the option. The given text is printed
in the synopsis of the command, which is part of the short and the long help and
the man page. It defaults to the string "val".
This directive is ignored for flag options (options without an argument).
arg_info
This directive determines whether the option takes an argument. The possible values
are no_arg, required_arg and optional_arg which indicate, respectively, that the
option takes no argument at all, an argument which is mandatory, or an argument
which may be omitted. The default value is no_arg. Hence an option works as a flag
if the arg_info directive is not given.
Note that arguments to options which take an optional argument must be given as
--foo=bar rather than --foo bar because the latter form would be ambiguous.
arg_type
For flag options this directive should be set to none, or not set at all. For
options which take an argument, the value of the directive determines the type of
the argument. Possible values are string for options which take a string argument,
and int32, uint32. int64, uint64, for options which take a numeric argument.
flag Lopsub maintains for each option a bitmask which contains the value of each
possible flag for this option. Flags may be accumulated by defining multiple flag
directives in the suite. Note there is no equal sign between the flag directive and
its value.
The following flags are defined.
multiple
This flag instructs the lopsub library to keep track of all given arguments
to an option, not just one as for ordinary options. This is only relevant
for options which take an (optional or required) argument.
required
Instruct the parser to fail if this option is not given in the argument
vector. If an option may be given at the command line or in the config file,
this flag should be avoided because the command line argv vector will not be
parsed successfully if the option is only given in the config file. The
recommended way to deal with this situation is to parse command line and
config file separately, then merge the two parse results and check in the
application if the option is given in the merged parse result.
There is another disadvantage of this flag: if the parser fails due to a
missing option that was declared required, it is not possible to detect if
other options were given. For example, if the suite defines the --help
option, and the application is executed with this option only, the parser
will still return a parse error.
ignored
This flag indicates that the current option is in fact not a real option.
In particular, name and short_opt are both ignored. The purpose of this flag
is to add additional information for the help output and the man page.
values Create an enumerable option.
Enumerable options take one out of a fixed set of possible values which are
predefined in the suite. Such options are always of type string. It is an error if
a different argument type was specified or if the option was defined to not take an
argument.
The syntax for the array of values is
values = {ID_0 = "string_0", ..., ID_N = "string_N"}
For each option for which the values directive was specified, the lopsubgen command
generates a C enumeration which contains the given identifiers. This allows
referring to each possible value through a numeric constant.
default_val
This directive makes only sense for options which take an argument. For such
options it defines the value the option parser provides automatically if the option
is not given in the argument vector.
If no default_val is specified in the suite, and the option is not given in the
argument vector either, the implied value depends on the argument type. For numeric
options, a value of zero is assumed. For options which take a string argument, a
NULL pointer is returned. For enum options, the first possible value (index zero)
is taken as the default.
help The detailed, multi-line help text for the current option. Included in the man page
and the long help.
EXAMPLE
A minimal suite and the corresponding "application".
The suite file hello.suite:
[suite hello]
[supercommand hello]
purpose = hello world
[option world]
summary = add "world"
The "application" hello.c:
#include <stdio.h> /* printf(3) */
#include <stdlib.h> /* exit(3) */
#include <lopsub.h>
#include "hello.lsg.h"
int main(int argc, char **argv)
{
struct lls_parse_result *lpr;
const struct lls_opt_result *result;
const struct lls_command *cmd = lls_cmd(0, hello_suite);
int ret;
ret = lls_parse(argc, argv, cmd, &lpr, NULL);
if (ret < 0) {
fprintf(stderr, "%s\n", lls_strerror(-ret));
exit(1);
}
printf("hello");
result = lls_opt_result(LSG_HELLO_HELLO_OPT_WORLD, lpr);
if (lls_opt_given(result))
printf(" world");
printf("\n");
exit(0);
}
Generate hello.lsg.c and hello.lsg.h:
$ lopsubgen --gen-c --gen-h < hello.suite
Compile hello.c and hello.lsg.c to produce the hello executable:
$ cc hello.c hello.lsg.c -o hello -llopsub
Run it:
$ ./hello
hello
$ ./hello --world
hello world
$ ./hello -w
option not recognized
$ ./hello 42
invalid number of arguments
Generate and examine the manual page:
$ lopsubgen --gen-man < hello.suite
$ man -l ./hello.lsg.man
SEE ALSO
lopsubgen(1), lopsub(7), lopsubex(1), gengetopt(1), getopt(1), getopt(3)