NAME

       sane-dc210 - SANE backend for Kodak DC210 Digital Camera

DESCRIPTION

       The  sane-dc210  library  implements a SANE (Scanner Access Now Easy) backend that provides access to the
       Kodak DC210 camera. THIS IS EXTREMELY ALPHA CODE!  USE AT YOUR OWN RISK!!

DEVICE NAMES

       The current version of the backend only allows one camera to be connected.  The  device  name  is  always
       "0".

CONFIGURATION

       The contents of the dc210.conf specify the serial port and baud rate to use.  The baud rate specifies the
       maximum  rate to use while downloading pictures.  (The camera is always initialized using 9600 baud, then
       switches to the higher rate).  On my 90MHz Pentium, I usually have no problems downloading at 115200 baud
       as long as the system is not excessively busy and the "interrupt-unmask flag" is set in  the  IDE  driver
       (hdparm -u1).  Supported baud rates are: 9600, 19200, 38400, 57600, and 115200.

       The dumpinquiry line causes some information about the camera to be printed.

       cmdrespause  specifies  how  many  usec  (1,000,000ths  of a) between writing the command and reading the
       result should be used. 125000 seems to be the lowest I could go reliably.

       breakpause is the time in 1,000,000ths of a usec between sending the  "back  to  default"  break  sending
       commands.

       Empty  lines  and  lines starting with a hash mark (#) are ignored.  A sample configuration file is shown
       below:

              port=/dev/ttyS0
              # this is a comment
              baud=115200
              dumpinquiry
              cmdrespause=125000
              breakpause=1000000

FILES

       @CONFIGDIR@/dc210.conf
              The backend configuration file (see also description of SANE_CONFIG_DIR below).

       @LIBDIR@/libsane-dc210.a
              The static library implementing this backend.

       @LIBDIR@/libsane-dc210.so
              The shared library implementing this backend (present on systems that support dynamic loading).

ENVIRONMENT

       SANE_CONFIG_DIR
              This environment variable specifies the list of directories that  may  contain  the  configuration
              file.   Under UNIX, the directories are separated by a colon (`:'), under OS/2, they are separated
              by a semi-colon (`;').  If this variable is not set, the configuration file  is  searched  in  two
              default  directories:  first, the current working directory (".") and then in @CONFIGDIR@.  If the
              value of the environment variable ends with the directory separator character,  then  the  default
              directories  are  searched  after  the  explicitly  specified  directories.   For example, setting
              SANE_CONFIG_DIR to "/tmp/config:" would result in directories "tmp/config", ".", and "@CONFIGDIR@"
              being searched (in this order).

       SANE_DEBUG_DC210
              If the library was compiled with debugging support enabled, this environment variable controls the
              debug level for this backend.  A value of 128 requests maximally  copious  debug  output;  smaller
              levels reduce verbosity.

SEE ALSO

       sane(7)

AUTHOR

       Brian J. Murrell

       This backend is based somewhat on the dc25 backend included in this package by Peter Fales.

       The manpage was copied from the dc25 backend and somewhat edited by Henning Meier-Geinitz.

BUGS

       Known bugs/limitations are: ?

       More  general  comments,  suggestions,  and  inquiries  about  frontends  or  SANE  should go to the SANE
       Developers mailing list (see http://www.sane-project.org/mailing-lists.html for details).   You  must  be
       subscribed to the list, otherwise your mail won't be sent to the subscribers.

@PACKAGEVERSION@                                   11 Jul 2008                                     sane-dc210(5)