Ubuntu Manpage: sane-mustek_pp - SANE backend for Mustek parallel port flatbed scanners

NAME

       sane-mustek_pp - SANE backend for Mustek parallel port flatbed scanners

DESCRIPTION

The sane-mustek_pp library implements a SANE (Scanner Access Now Easy) backend that provides access to
Mustek parallel port flatbed scanners and OEM versions.

There are 2 classes of Mustek parallel port scanners: regular CCD (cold cathode device) scanners and CIS
(contact image sensor) scanners.

The current version of this backend supports both CCD type scanners and CIS type scanners.

The following scanners might work with this backend:

CCD scanners
Model: ASIC ID: CCD Type: works:
--------------------------------------------------------------
SE 6000 P 1013 00 yes
SM 4800 P 1013/1015 04/01 yes
SE 1200 ED Plus 1015 01 no
SM 1200 ED Plus 1015 01 no
SE 12000 P 1505 05 no
600 III EP Plus 1013/1015 00/01 yes
SE 600 SEP 1013 ?? yes
600 II EP ???? ?? no
MD9848 1015 00 yes
Gallery 4800 ???? ?? yes
Viviscan Compact II 1013 00 yes

CIS scanners
Model: ASIC ID: works:
-----------------------------------------------
Mustek 600 CP & 96 CP 1015 yes (*)
Mustek 1200 CP 1015 yes
Mustek 1200 CP+ 1015 yes

OEM versions Original works
--------------------------------------------------
Medion/LifeTec/Tevion
MD/LT 9350/9351 1200 CP yes
MD/LT 9850/9851 1200 CP maybe (**)
MD/LT 9858 1200 CP probably
MD/LT 9890/9891 1200 CP yes
Targa
Funline TS12EP 1200 CP yes
Funline TS6EP 600 CP yes
Trust
Easy Connect 9600+ 600 CP yes
Cybercom
9352 1200 CP yes (***)

(*) Calibration problems existed with earlier version of this driver. They seem to be solved now.

(**) Problems have been reported in the past for the MD/LT9850 type (striped scans, head moving in
wrong direction at some resolutions). It is not known whether the current version of the driver
still has these problems.

IF YOU HEAR LOUD CLICKING NOISES, IMMEDIATELY UNPLUG THE SCANNER ! (This holds for any type of scanner).

(***) Possibly, the engine_delay parameter has to be set to 1 ms for accurate engine movements.

Please note that this backend is still under construction. Certain models are currently not supported and
some may never be because the communication protocol is still unknown (eg., SE 12000 P).

Some scanners work faster when EPP/ECP is enabled in the BIOS. EPP mode however may lead to hard-locks on
some Linux systems. If that is the case for you, you can either disable ECP/EPP in your BIOS or disable
it in the backend itself (see GLOBAL OPTIONS).

Note that the backend needs to run as root or has to have appropriate access rights to /dev/parport* if
libieee1284 support is compiled in. To allow user access to the scanner run the backend through the
network interface (See saned(8) and sane-net(5)). Note also that the backend does not support parport
sharing, i.e. if you try printing while scanning, your computer may crash. To enable parport sharing, you
have to enable libieee1284 at compile time. This backend also conflicts with the sane-musteka4s2(5)
backend. You can only enable one of them in your dll.conf. However, you have to enable the backend
explicitly in your dll.conf, just remove the hash mark in the line "mustek_pp".

DEVICE DEFINITION

This backend allows multiple devices being defined and configured via the mustek_pp.conf file (even
simultaneously, provided that they are connected to different parallel ports). Please make sure to edit
this file before you use the backend.

A device can be defined as follows:

scanner <name> <port name> <driver>

where

<name> is an arbitrary name for the device, optionally enclosed by double quotes, for instance "LifeTec
9350".

<port name> is the name of the parallel port to which the device is connected. In case libieee1284 is
used for communication with the port (default setup), valid port names are parport0, parport1, and
parport2.

In case the backend is configured for raw IO (old setup), port addresses have to be used instead of port
names: 0x378, 0x278, or 0x3BC. The mapping of parallel ports (lp0, lp1, and lp2) to these addresses can
be different for different Linux kernel versions. For instance, if you are using a Kernel 2.2.x or better
and you have only one parallel port, this port is named lp0 regardless of the base address. However, this
backend requires the base address of your port. If you are not sure which port your scanner is connected
to, have a look at your /etc/conf.modules, /etc/modules.conf and/or /proc/ioports.

If you are unsure which port to use, you can use the magic value * to probe for your scanner.

<driver> is the driver to use for this device. Currently available drivers are:

cis600 : for 600 CP, 96 CP & OEM versions
cis1200 : for 1200 CP & OEM versions
cis1200+ : for 1200 CP+ & OEM versions
ccd300 : for 600 IIIE P & OEM version

Choosing the wrong driver can damage your scanner!
Especially, using the 1200CP settings on a 600CP can be harmful. If the scanner starts making a
loud noise, turn it off immediately !!!

Using the cis600 driver on a 1200CP or a 1200CP+ is probably not dangerous. The cis1200+ driver also
works for the 1200CP, and using the cis1200 driver on a 1200CP+ will typically result in scans that cover
only half of the width of the scan area (also not dangerous).

If unsure about the exact model of your OEM version, check the optical resolution in the manual or on the
box: the 600CP has a maximum optical resolution of 300x600 DPI, whereas the 1200CP and 1200CP+ have a
maximum optical resolution of 600x1200 DPI.

Examples:

scanner "LifeTec 9350" 0x378 cis1200

scanner Mustek_600CP 0x378 cis600

scanner Mustek_600IIIEP * ccd300

If in doubt which port you have to use, or whether your scanner is detected at all, you can use
sane-find-scanner -p to probe all configured ports.

CONFIGURATION

The contents of the mustek_pp.conf file is a list of device definitions and device options that
correspond to Mustek scanners. Empty lines and lines starting with a hash mark (#) are ignored. Options
have the following format:

option <name> [<value>]

Depending on the nature of the option, a value may or may not be present. Options always apply to the
scanner definition that precedes them. There are no global options. Options are also driver-specific: not
all drivers support all possible options.

Common options
bw <value>
Black/white discrimination value to be used during lineart scanning. Pixel values below this value
are assumed to be black, values above are assumed to be white.
Default value: 127
Minimum: 0
Maximum: 255

Example: option bw 150

CIS driver options
top_adjust <value>
Vertical adjustment of the origin, expressed in millimeter (floating point). This option can be
used to calibrate the position of the origin, within certain limits. Note that CIS scanners are
probably temperature sensitive, and that a certain inaccuracy may be hard to avoid. Differences in
offset between runs in the order of 1 to 2 mm are not unusual.
Default value: 0.0
Minimum: -5.0
Maximum: 5.0

Example: option top_adjust -2.5

slow_skip
Turns fast skipping to the start of the scan region off. When the region to scan does not start at
the origin, the driver will try to move the scanhead to the start of the scan area at the fastest
possible speed. On some models, this may not work, resulting in large inaccuracies (up to
centimeters). By setting this option, the driver is forced to use normal speed during skipping,
which can circumvent the accuracy problems. Currently, there are no models for which these
inaccuracy problems are known to occur.

By default, fast skipping is used.

Example: option slow_skip

engine_delay <value>
Under normal circumstances, it is sufficient for the driver to wait for the scanner signaling that
the engine is stable, before a new engine command can be transmitted. In rare cases, certain
scanners and/or parallel port chipsets appear to prevent reliable detection of the engine state.
As a result, engine commands are transmitted too soon and the movement of the scanner head becomes
unreliable. Inaccuracies ranging up to 10 cm over the whole vertical scan range have been
reported. To work around this problem, the engine_delay option can be set. If it is set, the
driver waits an additional amount of time after every engine command, equal to the engine_delay
parameter, expressed in milliseconds. It practice an engine_delay of 1 ms is usually sufficient.
The maximum delay is 100 ms.

Note that every additional ms of delay can add up to 14 seconds to the total scanning time
(highest resolution), so an as small as possible value is preferred.

Default value: 0
Minimum: 0
Maximum: 100

Example: option engine_delay 1

CCD driver options
top <value>
Number of scanlines to skip to the start of the scan area. The number can be any positive integer.
Values known to me are 47 and 56.

Default value: 47
Minimum: 0
Maximum: none

Example: option top 56

waitbank <value>
The number of usecs to wait for a bank change. You should not touch this value actually. May be
any positive integer

Default value: 700
Minimum: 0
Maximum: none

Example: option waitbank 700

A sample configuration file is shown below:

#
# LifeTec/Medion 9350 on port 0x378
#
scanner "LifeTec 9350" 0x378 cis1200

# Some calibration options (examples!).
option bw 127
option top_skip -0.8

#
# A Mustek 600CP on port 0x3BC
#
scanner "Mustek 600CP" 0x3BC cis600

# Some calibration options (examples!).
option bw 120
option top_skip 1.2

#
# A Mustek 1200CP+ on port 0x278
#
scanner "Mustek 1200CP plus" 0x278 cis1200+

# Some calibration options (examples!).
option bw 130
option top_skip 0.2

#
# A Mustek 600 III EPP on port parport0
#
scanner "Mustek 600 III EPP" parport0 ccd300

# Some calibration options (examples!).
option bw 130
option top 56

GLOBAL OPTIONS

       You can control the overall behaviour of the sane-stek_pp backend by global  options  which  precede  any
       scanner definition in the mustek_pp.conf file.

       Currently, there is only one global option:

   Global options
       no_epp Disable  parallel  port  mode EPP: works around a known bug in the Linux parport code. Enable this
              option, if the backend hangs when trying to access the parallel port in EPP mode.

              Default value: use EPP

              Example:  option no_epp

FILES

       /etc/sane.d/mustek_pp.conf
              The backend configuration file (see also description of SANE_CONFIG_DIR below).

       /usr/lib/x86_64-linux-gnu/sane/libsane-mustek_pp.a
              The static library implementing this backend.

       /usr/lib/x86_64-linux-gnu/sane/libsane-mustek_pp.so
              The shared library implementing this backend (present on systems that support dynamic loading).

ENVIRONMENT

       SANE_CONFIG_DIR
              This environment variable specifies the list of directories that  may  contain  the  configuration
              file.   On  *NIX  systems,  the  directories  are separated by a colon (`:'), under OS/2, they are
              separated by a semi-colon (`;').  If this variable is not set, the configuration file is  searched
              in  two  default  directories: first, the current working directory (".") and then in /etc/sane.d.
              If the value of the environment variable ends with the directory  separator  character,  then  the
              default directories are searched after the explicitly specified directories.  For example, setting
              SANE_CONFIG_DIR to "/tmp/config:" would result in directories tmp/config, ., and /etc/sane.d being
              searched (in this order).

       SANE_DEBUG_MUSTEK_PP
              If  the  library  was  compiled with debug support enabled, this environment variable controls the
              debug level for this backend.  E.g., a value of 128 requests  all  debug  output  to  be  printed.
              Smaller levels reduce verbosity.

              level   debug output
              --------------------------------------
               0      nothing
               1      errors
               2      warnings & minor errors
               3      additional information
               4      debug information
               5      code flow (not supported yet)
               6      special debug information

       SANE_DEBUG_SANEI_PA4S2
              This  variable  sets the debug level for the SANE interface for the Mustek chipset A4S2. Note that
              enabling this will spam your terminal with some million lines of debug output.

              level   debug output
              ----------------------------
               0      nothing
               1      errors
               2      warnings
               3      things nice to know
               4      code flow
               5      detailed code flow
               6      everything

AUTHORS

       Jochen Eisinger
       <jochen at penguin-breeder dot org>
       Eddy De Greef
       <eddy_de_greef at scarlet dot be>

BUGS

       Too many... please send  bug  reports  to  sane-devel@alioth-lists.debian.net  (note  that  you  have  to
       subscribe      first      to      the      list     before     you     can     send     emails...     see
       http://www.sane-project.org/mailing-lists.html).

BUG REPORTS

       If something doesn't work, please contact us (Jochen for the CCD scanners, Eddy for  the  CIS  scanners).
       But we need some information about your scanner to be able to help you...

       SANE version
              Run scanimage -V to determine this.

       the backend version and your scanner hardware
              Run  SANE_DEBUG_MUSTEK_PP=128  scanimage  -L  as  root.  If  you  don't  get  any  output from the
              sane-mustek_pp backend, make sure a line "mustek_pp" is included into  your  /etc/sane.d/dll.conf.
              If  your  scanner  isn't  detected,  make  sure  you've  defined  the  right  port address in your
              mustek_pp.conf.

       the name of your scanner/vendor also a worthy information. Please also include the
              optical resolution and lamp type of your scanner, both can be found in the manual of your scanner.

       any further comments
              if you have comments about the documentation (what could be done better), or you  think  I  should
              know something, please include it.

                                                   13 Jul 2008                                 sane-mustek_pp(5)