Provided by: iotop-c_1.23-1_amd64 
NAME
iotop - simple top-like I/O monitor
SYNOPSIS
iotop [OPTIONS]
DESCRIPTION
iotop watches I/O usage information available in the Linux kernel (requires 2.6.20 or
later) and displays a table of current I/O usage by processes or threads on the system. At
least the CONFIG_TASK_DELAY_ACCT, CONFIG_TASK_IO_ACCOUNTING, CONFIG_TASKSTATS and
CONFIG_VM_EVENT_COUNTERS options need to be enabled in your Linux kernel build
configuration.
Running iotop as non-root user is possible by adding the NET_ADMIN capability. This can be
done by e.g.:
$ sudo setcap 'cap_net_admin+eip' <path-to>/iotop
Be warned that this will also allow other users to run it and get access to information
that normally should not be available to them.
iotop displays columns for the I/O bandwidth read and written by each process/thread
during the sampling period. It also displays the percentage of time the thread/process
spent while swapping in and while waiting on I/O. For each process, its I/O priority
(class/level) is shown.
In addition, the total I/O bandwidth read and written during the sampling period are
displayed at the top of the interface. Total DISK READ and Total DISK WRITE values
represent total read and write bandwidth between processes and kernel threads on one side
and kernel block device subsystem on the other. While Current DISK READ and Current DISK
WRITE values represent corresponding bandwidths for current disk I/O between the kernel
block device subsystem and the underlying hardware (HDD, SSD, etc.). Thus Total and
Current values may not be equal at any given moment of time due to data caching and I/O
operations reordering that take place inside the Linux kernel.
Use the left and right arrows to select the sort column, r or space to reverse the sorting
order, o to toggle the --only option (this uses the visible values from the GRAPH column
or the IO column in case the GRAPH column is hidden), p to toggle the --processes option,
a to cycle between the --accumulated, --accum-bw and normal operation, i to change the
priority of a thread or a process's thread, f to change filtering by UID/PID (--user and
--pid options), 1-9 to toggle the visibility of the respective column, 0 to show all
columns, up/down arrows, page-up/page-down/home/end keys to scroll and q to quit. Any
unrecognized key will be ignored.
All processes or threads that have exited are displayed grayed for the same time as is
visible in the GRAPH column or 3 seconds when it is hidden. The invalid data points in the
GRAPHS column are displayed inverse or with letter x (see option --dead-x and x shortcut).
When using unicode characters each position contains two datapoints and only the positions
with two invalid data points are reversed.
It is possible for threads of a process to have different priority from their main
process. This is shown with ! in the PRIO column of the main process as e.g. !be/4.
Threads activity is always aggregated with and shown inside the main process.
When showing threads, they always appear below their main process and are sorted in the
same way as the processes.
There are two ways to change the IO priority of a process or thread - press i and use
arrows to select the process or thread from the visible ones on screen or press i and type
its TID (PID and TID have the same value for the main process). Then use tab and arrows to
change the priority value and confirm with enter. Shortcuts esc or q will cancel this
mode.
To change the UID and PID filters, press f and use tab to select the UID or PID field,
then type the numerical id or n to remove the filter and confirm with enter. Filtering is
always done by TID because it is unique. Note that for the main process PID is the same as
TID. Shortcuts esc or q will cancel this mode.
Starting with Linux kernel 5.14.x task_delayacct is configurable at runtime and set to off
by default. This setting can be changed in interactive mode by the Ctrl-T shortcut. In
batch mode a warning is printed when the setting is OFF. From the command line this can be
enabled by:
$ sudo sysctl kernel.task_delayacct=1
and disabled again by:
$ sudo sysctl kernel.task_delayacct=0
It is advisable to keep this option off when not using this or another monitoring program
because when enabled it has some effect on system performance.
OPTIONS
-v, --version
Show the version number and exit
-h, --help
Show usage information and exit
-H, --help-type=TYPE
Set the type of interactive help shown. Accepted values for TYPE are none, win and
inline.
-o, --only
Only show processes or threads actually doing I/O, instead of showing all processes
or threads. This can be dynamically toggled by pressing o
--no-only
Show all processes or threads
-b, --batch
Turn on non-interactive mode. Useful for logging I/O usage over time
-n NUM, --iter=NUM
Set the number of iterations before quitting (never quit by default). This is most
useful in non-interactive mode
-d SEC, --delay=SEC
Set the delay between iterations in seconds (1 second by default). Accepts
non-integer values such as 1.1 seconds
-p PID, --pid=PID
A process/thread id to monitor (all by default)
-u USER, --user=USER
A user id to monitor (all by default). The value will always be resolved first
unless it is prefixed by + in which case it is treated as numeric only. Values that
do not resolve but appear to be numeric are used as numeric
-P, --processes
Only show processes. Normally iotop shows processes and all threads
--no-processes
Show processes and all threads
-a, --accumulated
Show accumulated I/O instead of bandwidth. In this mode, iotop shows the amount of
I/O processes have done since the process or iotop started. Note that this option
and --accum-bw are exclusive and they will turn each other off
--no-accumulated
Show bandwidth (useful when changing config file with --write)
-A, --accum-bw
Show accumulated I/O as bandwidth for the whole sampling period. In this mode,
iotop shows the amount of I/O per second for the whole period since the process or
iotop started Note that this option and --accumulated are exclusive and they will
turn each other off
--no-accum-bw
Show bandwidth (useful when changing config file with --write)
-k, --kilobytes
Use kilobytes instead of a human friendly unit. This mode is useful when scripting
the batch mode of iotop. Instead of choosing the most appropriate unit iotop will
display all sizes in kilobytes
--no-kilobytes
Use human friendly units
-t, --time
Add a timestamp on each line (implies --batch). Each line will be prefixed by the
current time
-c, --fullcmdline
Show processes' full file path and parameters
--no-fullcmdline
Show processes' names only
-1, --hide-pid
Hide PID/TID column
--show-pid
Show PID/TID column
-2, --hide-prio
Hide PRIO column
--show-prio
Show PRIO column
-3, --hide-user
Hide USER column
--show-user
Show USER column
-4, --hide-read
Hide DISK READ column
--show-read
Show DISK READ column
-5, --hide-write
Hide DISK WRITE column
--show-write
Show DISK WRITE column
-6, --hide-swapin
Hide SWAPIN column
--show-swapin
Show SWAPIN column
-7, --hide-io
Hide IO column
--show-io
Show IO column
-8, --hide-graph
Hide GRAPH column
--show-graph
Show GRAPH column
-9, --hide-command
Hide COMMAND column
--show-command
Show COMMAND column
-g TYPE, --grtype=TYPE
Set GRAPH column data source. Accepted values for TYPE are io, r, w, rw and sw.
-R, --reverse-graph
Reverse GRAPH direction - show most recent values on the right side
--no-reverse-graph
Do not reverse GRAPH direction - show most recent values on the left side
-q, --quiet
Suppress some lines of header (implies --batch). This option can be specified up to
three times to remove header lines
-q column names are only printed on the first iteration,
-qq column names are never printed,
-qqq the I/O summary is never printed
-x, --dead-x
Show exited processes/threads with letter x instead of inverse background
--no-dead-x
Show exited processes/threads with inverse background
-e, --hide-exited
Hide exited processes
--show-exited
Show exited processes
-l, --no-color
Do not colorize values
--color
Colorize values. This will override the effect of the environment variable NO_COLOR
when explicitly specified on the command line.
--si Use SI units of 1000 when printing values. The default is non-SI 1024
--no-si
Use non-SI units of 1024 when printing values
--threshold=1..10
Set the threshold to switch to next unit. The default value is 2
--ascii
Disable using Unicode
--unicode
Use Unicode drawing chars
-W, --write
Merge the preceding options to the current config, save the config and exit. Note
that all options after this one will be ignored.
KEYBOARD SHORTCUTS
q, Q Exit
W Save current settings to configuration file in $HOME/.config/iotop/iotoprc
D Reset all settings to their default values
<space>, r
Toggle sort order
<home> Scroll to the top of the list
<end> Scroll to the bottom of the list
<page-up>
Scroll one screen up
<page-down>
Scroll one screen down
<up> Scroll one line up
<down> Scroll one line down
<right>
Sort by next column
<left> Sort by previous column
<esc> Cancel ionice or filter selection. In case only the help window is open then close
it
o, O Toggle showing only processes with IO activity
p, P Toggle showing processes/threads
a, A Cycle showing accumulated/accum-bw/current values
? Toggle showing inline help
h, H Toggle showing window help
c, C Toggle showing full command line
1, 2, 3, 4, 5, 6, 7, 8, 9
Toggle showing the column (column number corresponds to the shortcut)
0 Show all columns
g, G Cycle GRAPH source (IO=IO, R=DISK READ , W=DISK WRITE, R+W=DISK READ+DISK WRITE,
SW=SWAPIN). Using g will cycle forward and G will cycle backward.
R Toggle reverse GRAPH direction
i, I IOnice a process/thread (depends on process/thread display mode)
f, F Change UID and PID filters
u, U Toggle using Unicode/ASCII characters for pseudo graph
l, L Toggle colorizing values
x, X Toggle the display mode of exited processes/threads between letter x and inverse
background
e, E Toggle the display of exited processes
s, S Toggle freeze of data collection
Ctrl-B Toggle SI units
Ctrl-R Cycle unit threshold
Ctrl-T Toggle task_delayacct kernel sysctl
Ctrl-L Redraw screen
/ Change search regular expression. While the search regular expression is being
edited, there is an indicator next to it that shows if the expression is valid.
The search is confirmed by <enter> or cancelled by <esc>.
List of shortcuts in the editor:
<esc> Cancel editing and remove the regular expression filter
<enter>
Confirm the current regular expression and exit edit mode. In case the
regular expression is empty or invalid it will match everything.
Alt/Meta-<backspace>, Ctrl-W
Delete one word from cursor to the left
Alt/Meta-D
Delete one word from cursor to the right
Alt/Meta-B, Ctrl-<left>
Move the cursor to the beginning of the word on the left
Alt/Meta-F, Ctrl-<right>
Move the cursor after the end of the word on the right
Ctrl-A, <home>
Move the cursor to the leftmost position
Ctrl-E, <end>
Move the cursor after the last character
Ctrl-B, <left>
Move the cursor to the left
Ctrl-F, <right>
Move the cursor to the right
Ctrl-H, <backspace>
Delete the character left of cursor
Ctrl-D, <del>
Delete the character under the cursor
Ctrl-K Delete from the character under the cursor to the end of the line
Ctrl-U Delete everything
[anything-else]
Non-printable characters are ignored. Normal characters are inserted before
the character under the cursor. UTF-8 sequences are parsed and treated as a
single character. Unicode combining characters will be appended to the
character under the cursor.
ENVIRONMENT
As per the recommendation of https://www.no-color.org/ iotop honors the contents of the
environment variable NO_COLOR and when it is set to a non empty string, all color output
is suppressed.
SEE ALSO
ionice(1), top(1), vmstat(1), atop(1), htop(1)
AUTHOR
The original Python iotop implementation was written by Guillaume Chazarain. This rewrite
in C was started in 2014 by Vyacheslav Trushkin and reworked to include all missing
features from the original Python code and several new ones from 2020 to 2023 by Boian
Bonev.
This manual page was started by Paul Wise for the Debian project and is placed in the
public domain.
January 22, 2023 IOTOP(8)