Provided by: uucp_1.07-27build3_amd64 
NAME
uucico - UUCP file transfer daemon
SYNOPSIS
uucico [ options ]
DESCRIPTION
The uucico daemon processes file transfer requests queued by uucp (1) and uux (1). It is
started when uucp or uux is run (unless they are given the -r option). It is also
typically started periodically using entries in the crontab table(s).
When invoked with -r1, --master, -s, --system, or -S, the daemon will place a call to a
remote system, running in master mode. Otherwise the daemon will start in slave mode,
accepting a call from a remote system. Typically a special login name will be set up for
UUCP which automatically invokes uucico when a call is made.
When uucico terminates, it invokes the uuxqt (8) daemon, unless the -q or --nouuxqt option
is given; uuxqt (8) executes any work orders created by uux (1) on a remote system, and
any work orders created locally which have received remote files for which they were
waiting.
If a call fails, uucico will normally refuse to retry the call until a certain
(configurable) amount of time has passed. This may be overridden by the -f, --force, or
-S option.
The -l, --prompt, -e, or --loop options may be used to force uucico to produce its own
prompts of "login: " and "Password:". When another daemon calls in, it will see these
prompts and log in as usual. The login name and password will normally be checked against
a separate list kept specially for uucico rather than the /etc/passwd file; it is possible
on some systems to direct uucico to use the /etc/passwd file. The -l or --prompt option
will prompt once and then exit; in this mode the UUCP administrator or the superuser may
use the -u or --login option to force a login name, in which case uucico will not prompt
for one. The -e or --loop option will prompt again after the first session is over; in
this mode uucico will permanently control a port.
If uucico receives a SIGQUIT, SIGTERM or SIGPIPE signal, it will cleanly abort any current
conversation with a remote system and exit. If it receives a SIGHUP signal it will abort
any current conversation, but will continue to place calls to (if invoked with -r1 or
--master) and accept calls from (if invoked with -e or --loop) other systems. If it
receives a SIGINT signal it will finish the current conversation, but will not place or
accept any more calls.
OPTIONS
The following options may be given to uucico.
-r1, --master
Start in master mode (call out to a system); implied by -s, --system, or -S. If no
system is specified, call any system for which work is waiting to be done.
-r0, --slave
Start in slave mode. This is the default.
-s system, --system system
Call the named system.
-S system
Call the named system, ignoring any required wait. This is equivalent to -s system
-f.
-f, --force
Ignore any required wait for any systems to be called.
-l, --prompt
Prompt for login name and password using "login: " and "Password:". This allows
uucico to be easily run from inetd (8). The login name and password are checked
against the UUCP password file, which probably has no connection to the file
/etc/passwd. The --login option may be used to force a login name, in which cause
uucico will only prompt for a password.
-p port, --port port
Specify a port to call out on or to listen to.
-e, --loop
Enter endless loop of login/password prompts and slave mode daemon execution. The
program will not stop by itself; you must use kill (1) to shut it down.
-w, --wait
After calling out (to a particular system when -s, --system, or -S is specified, or
to all systems which have work when just -r1 or --master is specified), begin an
endless loop as with --loop.
-q, --nouuxqt
Do not start the uuxqt (8) daemon when finished.
-c, --quiet
If no calls are permitted at this time, then don't make the call, but also do not put
an error message in the log file and do not update the system status (as reported by
uustat (1)). This can be convenient for automated polling scripts, which may want to
simply attempt to call every system rather than worry about which particular systems
may be called at the moment. This option also suppresses the log message indicating
that there is no work to be done.
-C, --ifwork
Only call the system named by -s, --system or -S if there is work for that system.
-D, --nodetach
Do not detach from the controlling terminal. Normally uucico detaches from the
terminal before each call out to another system and before invoking uuxqt. This
option prevents this.
-u name, --login name
Set the login name to use instead of that of the invoking user. This option may only
be used by the UUCP administrator or the superuser. If used with --prompt, this will
cause uucico to prompt only for the password, not the login name.
-z, --try-next
If a call fails after the remote system is reached, try the next alternate rather
than simply exiting.
-i type, --stdin type
Set the type of port to use when using standard input. The only support port type is
TLI, and this is only available on machines which support the TLI networking
interface. Specifying -iTLI causes uucico to use TLI calls to perform I/O.
-x type, -X type, --debug type
Turn on particular debugging types. The following types are recognized: abnormal,
chat, handshake, uucp-proto, proto, port, config, spooldir, execute, incoming,
outgoing.
Multiple types may be given, separated by commas, and the --debug option may appear
multiple times. A number may also be given, which will turn on that many types from
the foregoing list; for example, --debug 2 is equivalent to --debug abnormal,chat.
The debugging output is sent to the debugging file, which may be printed using uulog
-D.
-I file, --config file
Set configuration file to use. This option may not be available, depending upon how
uucico was compiled.
-v, --version
Report version information and exit.
--help
Print a help message and exit.
SEE ALSO
kill(1), uucp(1), uux(1), uustat(1), uuxqt(8)
AUTHOR
Ian Lance Taylor <ian@airs.com>
Taylor UUCP 1.07 uucico(8)