Provided by: ap-utils_1.5-5_amd64 
NAME
ap-gl - configure and monitor ATMEL_PRISM based APs
SYNOPSIS
ap-gl
DESCRIPTION
ap-gl to config and get stats from Atmel-chipset based AP with ATMEL_PRISM Private MIB
support.
MENU
Info/
SysInfo
Get info about AP hardware and software
Ethernet
This option displays the Ethernet statistics for your reference.
Wireless
This option displays the wireless statistics for your reference.
Stations (atmel)
Under this menu the user will be able to see the Associated Stations that are
currently associated with the Access Point. For each associated station the user
will be able to see the MAC Address. From version 0.7.3-pre1 you may save mac
addresses list to file ~/<util_name>.stations. For each associated station the
user will be able to see the MAC Address, Link Quality, RSSI and Idle time.
* Mac address: If the association is pending (that is, the Client is scanning,
authenticating or associating), assocAddress contains the MAC address of that
Client with the group bit set to indicate that the Access Point is aware of the
presence of that Client. The other objects of the entry will be updated based on
the information extracted from the received Probe Requests.
* Link Quality: An indicator for the quality of the Client. If the association is
still pending, the quality is calculated over the received Probe Requests from the
Client. If the Client is associated, the quality derived from any activity with the
Client. The actual quality source depends on the selected quality indicator. The
semantics of the indicator is 'low is good quality' and 'high is bad quality'.
* IdleTime: An indicator (in seconds) for the age of the information on the
Client. The age is reset to 0 if any activity of this Client is detected.
* RSSI: An indicator for the RSSI of the Client. If the association is still
pending, the RSSI is calculated over the received Probe Requests from the Client.
If the Client is associated, the RSSI derived from any activity with the Client.
* Client stations Status: status 3 - normal connected, status 9 - awaiting
authorization.
KnownAP
By using option APs from info menu you may see all Access Points thats visible by
your AP.
* Link Quality: An indicator for the quality of the Client. If the association
is still pending, the quality is calculated over the received Probe Requests
from the Client. If the Client is associated, the quality derived from any
activity with the Client. The actual quality source depends on the selected
quality indicator. The semantics of the indicator is 'low is good quality' and
'high is bad quality'.
* RSSI: An indicator for the RSSI in dBm of the Client. If the association is
still pending, the RSSI is calculated over the received Probe Requests from
the Client. If the Client is associated, the RSSI derived from any activity with
the Client.
* WARNING! By reports this option my be dangerously - in some cases you may lost
you AP configuration and on SMC2655W the one way to fix it - only restore factory
defaults.
Config/
Bridging
IP configuration - If the server site supports DHCP function and the DHCP
Enable box is ticked; the IP address of an access point will be automatically
displayed and assigned; otherwise, you need to key in an IP address now. The
primary port provides a wired or wireless method to change the access point
setting. If the Ethernet option is ticked, the setting of an access point can be
done through Ethernet. If the Wireless option is ticked, the access point function
can be set through a wireless station. Wireless station means a laptop PC or a
desktop PC equipped with an IEEE802.11b PCMCIA card or USB dongle. Enable
SNMP Traps enables the SNMP trap function. You can view the records by using ap-
trapd utility. You are allowed to set your access point to be used as Access
point, Access point client, or Wireless bridge.
* Access Point - An internetworking device that seamlessly connects wired and
wireless networks together.
* Wireless bridge Point to point - The point-to-point wireless bridge
configuration uses two Wireless Bridge units to connect two separate LANs. You must
to fill in the Remote MAC Address before your bridge-function-enable access point
can work with it.
* Point to multipoint - When connecting three to more separate LANs, each LAN
located building requires a wireless bridge. This is called Multipoint wireless
bridge and again requires one Master bridge unit and two or more Slave bridge
units as required. If the point-to-multipoint option is selected, your bridge-
function-enable access point will designate as a Mater and to work with it,
others bridges need to be set as a point-to-point bridge and enter the MAC address
of the mater access point.
Wireless
You can give your access point a name and give it an ESSID (Extended Service
Station ID), which can allow other wireless stations, which knows the ESSID, to
link with it.
Privacy
The Privacy options allow you to enable 64-bit or 128-bit WEP (wired equivalent
privacy) encryption. If an encryption function is not needed, you can just simply
tick on the Disable box to disable it. If the 64-bit or 128-bit encryption
function is enabled, there are four sets of key need to be filled into the blanket
boxes. For the 64-bit encryption, each key is required to enter 5 Hex digits. For
example: 11 22 33 44 55. The 128-bit encryption requires each key to enter 13 Hex
digits. For example: 12 34 56 78 9A BC DE F0 11 22 33 44 55.
NOTE! The WEP keys you enter are really accepted and written to the AP, permanently
if you do an Upload from the Commands menu after setting them. However, the new
key values are not echoed to the user when you return to the Privacy settings under
the Config menu. This is a security feature of SNMP implementation in this
hardware.
Authorized MAC address
For security or management purpose, you can edit a list of authorized MAC
addresses, which are allowed to view or modify the setting of an access point.
Authorization Table Enable option allows you to enable or disable this function.
Community
The Community configuration allow you to set a phrase for administrator and
manufacturer community and a phrase for user community. If a user knows the phrase
of administrator, he/she is authorized to change the setting of an access point. If
a user only knows about the phrase of a user community; he/she is allowed to view
the setting of an access point but is not allowed to change the setting.
Radio Under the Radio user will be able to set or get the Transmitting Powervalues,
for the Control Register 31 of the Baseband, for each channel. Reg CR31: Under this
option user defines a value for the transmitted power (Value for the Control
register 31 of the baseband) and it must be in the range 128 (max) to 255 (min) in
Decimal form. Starting from version 0.6 of Access Point SNMP Config utility it's
possible to set power output level for your AP. You may set signal power output in
range from 0mw to 100mw by setting value for corresponding channel from 0 to 255
(0xFF). The scale is as follows:
Value: 00----------128--------255
Power: 0mw--------100mw-------0mw
So to get maximum power output from your AP set value for corresponding
channel to 128 (0x80). But sometimes better solution - experimentally choose values
for best link quality, sometimes not max. More info you can get from:
http://pasadena.net/aprf/;
http://www.wi2600.org/mediawhore/nf0/wireless/docs/802.11/WAP11/fun_with_the_wap11.txt.
Commands/
Upload After you ve changed any value or setting of an access point through the SNMP
config utility. You must come back to this option to make the new changes and
setting s validated. Also, only an administrator and manufacturer is allowed to do
such changes.
Defaults
Restore factory default configuration.
Reset Reset AP. All changed and not uploaded settings will be lost.
TestMode/
When user selects the Tests option a form will appear indicating a number of
parameter needed to be set by the user in order to perform the Radio test.
Antenna: Under this option we specify the antenna to be tested (A, B).
Tx Filter: Under this option user needs to select the Baseband transmitting
Filter to be used. There are two options (US, JPN) available since the bandwidth
for Europe - USA is 11MHz and for, Japan is 14MHz.
Rate: Under this option user needs to specify the rate to be used among the
following options 1Mbps, 2Mbps, 5.5Mbps and 11Mbps.
Channel: Under this option user needs to select the channel to be used.
There are 14 channels available. After setting the parameters there are three
commands available: Continuous Tx (with modulation), Continuous Tx (without
modulation) and Continuous Rx:
* Continuous Tx (with modulation): Using this command the MAC sets the transmitter
in continuous mode with modulation. We can measure the output power of the radio.
* Continuous Tx (without modulation): Using this command we can measure the
frequency accuracy of the radio. The MAC sets the baseband Processor in test mode
and turns off the spreading and scrambling codes.
* Continuous Rx: With this command user can set the device in a receiving mode.
Note: In order to perform the above test user needs to have a Spectrum Analyzer
connected.
Connect/
In order to make a connection with Access Point user needs to set two parameters.
The IP Address of the Access Point and the Community name (default 'public').
Search/
Find connected Access Points. Search for WNW APs only works if community set to
right AP community. It's useful if you know community but dont know what ip your AP
got from DHCP server. You must have support for multicasting enabled in kernel.
About/ About function shows the Wireless Access Point Configurator for Unix version and
short info.
Shell/ Run subshell. To return type 'exit'
NAVIGATION KEYS
In case you unable to use cursor keys to menu navigate - try to use "h" to go left, "j" to
go down, "k" to go up, "l" to go right, like vi editor.
AUTHOR
Roman Festchook <roma@polesye.net>
http://ap-utils.polesye.net
SEE ALSO
ap-trapd(8), ap-mrtg(8), ap-config(8)
Wireless Access Point Utilities for Unix ap-gl(8)