NAME

       Smokeping::probes::DismanPing - DISMAN-PING-MIB Probe for SmokePing

SYNOPSIS

        *** Probes ***

        +DismanPing

        offset = 50%
        pings = 15
        step = 300

        # The following variables can be overridden in each target section
        /^influx_.+/ = influx_location = In the basement
        ownerindex = smokeping
        packetsize = 56
        pinghost = pinger@router.example.com # mandatory
        pingsrc = 192.0.2.9

        # [...]

        *** Targets ***

        probe = DismanPing # if this should be the default probe

        # [...]

        + mytarget
        # probe = DismanPing # if the default probe is something else
        host = my.host
        /^influx_.+/ = influx_location = In the basement
        ownerindex = smokeping
        packetsize = 56
        pinghost = pinger@router.example.com # mandatory
        pingsrc = 192.0.2.9

DESCRIPTION

       Uses the DISMAN-PING-MIB to cause a remote system to send probes.

VARIABLES

       Supported probe-specific variables:

       offset
           If you run many probes concurrently you may want to prevent them from hitting your
           network all at the same time. Using the probe-specific offset parameter you can change
           the point in time when each probe will be run. Offset is specified in % of total
           interval, or alternatively as 'random', and the offset from the 'General' section is
           used if nothing is specified here. Note that this does NOT influence the rrds itself,
           it is just a matter of when data acquisition is initiated.  (This variable is only
           applicable if the variable 'concurrentprobes' is set in the 'General' section.)

           Example value: 50%

       pings
           How many pings should be sent to each target. Note that the maximum value for
           DismanPing MIP is 15, which is less than the SmokePing default, so this class has its
           own default value.  If your Database section specifies a value less than 15, you must
           also set it for this probe.  Note that the number of pings in the RRD files is fixed
           when they are originally generated, and if you change this parameter afterwards,
           you'll have to delete the old RRD files or somehow convert them.

           Example value: 15

           Default value: 15

       step
           Duration of the base interval that this probe should use, if different from the one
           specified in the 'Database' section. Note that the step in the RRD files is fixed when
           they are originally generated, and if you change the step parameter afterwards, you'll
           have to delete the old RRD files or somehow convert them. (This variable is only
           applicable if the variable 'concurrentprobes' is set in the 'General' section.)

           Example value: 300

       Supported target-specific variables:

       /^influx_.+/
           This is a tag that will be sent to influxdb and has no impact on the probe
           measurement. The tag name will be sent without the "influx_" prefix, which will be
           replaced with "tag_" instead. Tags can be used for filtering.

           Example value: influx_location = In the basement

       ownerindex
           The SNMP OwnerIndex to use when setting up the test.  When using VACM, can map to a
           Security Name or Group Name of the entity running the test.

           By default this will be set to

           Example value: smokeping

       packetsize
           The packetsize parameter lets you configure the packet size for the pings sent. The
           minimum is 8, the maximum 65507. Use the same number as with fping if you want the
           same packet sizes being used on the network.

           Default value: 56

       pinghost
           The (mandatory) pinghost parameter specifies the remote system which will execute the
           pings, as well as the SNMP community string on the device.

           Example value: pinger@router.example.com

           This setting is mandatory.

       pingsrc
           The (optional) pingsrc parameter specifies the source address to be used for pings.
           If specified, this parameter must identify an IP address assigned to pinghost.

           Example value: 192.0.2.9

AUTHORS

       Bill Fenner <fenner@research.att.com>, Tobi Oetiker <tobi@oetiker.ch>

NOTES

   MENU NAMES
       This probe uses the menu name of a test as part of the unique index.  If the menu name is
       longer than 32 characters, the last 32 characters are used for the index.  Collisions are
       *not* detected and simply cause one test's results to be used for all colliding names.

   CONFIGURATION
       This probe requires read/write access to the pingCtlTable.  It also requires read-only
       access to the pingResultsTable and the pingHistoryTable.  The DISMAN-PING-MIB is
       structured such that it is possible to restrict by pingCtlOwnerIndex.  This probe uses a
       pingCtlOwnerIndex of "SP on hostname" as ownerindex by default; use ownerindex to
       configure this if needed.

   SAMPLE JUNOS CONFIGURATION
       This configuration permits the community "pinger" read-write access to the full DISMAN-
       PING-MIB, but only when sourced from the manager at 192.0.2.134.

           snmp {
               view pingMIB {
                   oid .1.3.6.1.2.1.80 include;
               }
               community pinger {
                   view pingMIB;
                   authorization read-write;
                   clients {
                       192.0.2.134/32;
                   }
               }
           }

   SAMPLE CONFIGURATIONS NOTE
       This configuration allows the "pinger" community full access to the DISMAN-PING-MIB.
       There is information in the description of pingCtlOwnerIndex in RFC 4560
       (<http://tools.ietf.org/html/rfc4560>) about using the vacmViewTreeFamilyTable to further
       restrict access.  The author has not tried this method.