NAME

     write, writev, pwrite, pwritev — write output

LIBRARY

     Standard C Library (libc, -lc)

SYNOPSIS

     #include <unistd.h>

     ssize_t
     write(int fd, const void *buf, size_t nbytes);

     ssize_t
     pwrite(int fd, const void *buf, size_t nbytes, off_t offset);

     #include <sys/uio.h>

     ssize_t
     writev(int fd, const struct iovec *iov, int iovcnt);

     ssize_t
     pwritev(int fd, const struct iovec *iov, int iovcnt, off_t offset);

DESCRIPTION

     The write() system call attempts to write nbytes of data to the object referenced by the
     descriptor fd from the buffer pointed to by buf.  The writev() system call performs the same
     action, but gathers the output data from the iovcnt buffers specified by the members of the
     iov array: iov[0], iov[1], ..., iov[iovcnt-1].  The pwrite() and pwritev() system calls
     perform the same functions, but write to the specified position in the file without
     modifying the file pointer.

     For writev() and pwritev(), the iovec structure is defined as:

           struct iovec {
                   void   *iov_base;  /* Base address. */
                   size_t iov_len;    /* Length. */
           };

     Each iovec entry specifies the base address and length of an area in memory from which data
     should be written.  The writev() system call will always write a complete area before
     proceeding to the next.

     On objects capable of seeking, the write() starts at a position given by the pointer
     associated with fd, see lseek(2).  Upon return from write(), the pointer is incremented by
     the number of bytes which were written.

     Objects that are not capable of seeking always write from the current position.  The value
     of the pointer associated with such an object is undefined.

     If the real user is not the super-user, then write() clears the set-user-id bit on a file.
     This prevents penetration of system security by a user who “captures” a writable set-user-id
     file owned by the super-user.

     When using non-blocking I/O on objects such as sockets that are subject to flow control,
     write() and writev() may write fewer bytes than requested; the return value must be noted,
     and the remainder of the operation should be retried when possible.

RETURN VALUES

     Upon successful completion the number of bytes which were written is returned.  Otherwise a
     -1 is returned and the global variable errno is set to indicate the error.

ERRORS

     The write(), writev(), pwrite() and pwritev() system calls will fail and the file pointer
     will remain unchanged if:

     [EBADF]            The fd argument is not a valid descriptor open for writing.

     [EPIPE]            An attempt is made to write to a pipe that is not open for reading by any
                        process.

     [EPIPE]            An attempt is made to write to a socket of type SOCK_STREAM that is not
                        connected to a peer socket.

     [EFBIG]            An attempt was made to write a file that exceeds the process's file size
                        limit or the maximum file size.

     [EFAULT]           Part of iov or data to be written to the file points outside the
                        process's allocated address space.

     [EINVAL]           The pointer associated with fd was negative.

     [ENOSPC]           There is no free space remaining on the file system containing the file.

     [EDQUOT]           The user's quota of disk blocks on the file system containing the file
                        has been exhausted.

     [EIO]              An I/O error occurred while reading from or writing to the file system.

     [EINTR]            A signal interrupted the write before it could be completed.

     [EAGAIN]           The file was marked for non-blocking I/O, and no data could be written
                        immediately.

     [EROFS]            An attempt was made to write over a disk label area at the beginning of a
                        slice.  Use disklabel(8) -W to enable writing on the disk label area.

     [EINVAL]           The value nbytes is greater than SSIZE_MAX (or greater than INT_MAX, if
                        the sysctl debug.iosize_max_clamp is non-zero).

     [EINTEGRITY]       The backing store for fd detected corrupted data while reading.  (For
                        example, writing a partial filesystem block may require first reading the
                        existing block which may trigger this error.)

     In addition, writev() and pwritev() may return one of the following errors:

     [EDESTADDRREQ]     The destination is no longer available when writing to a UNIX domain
                        datagram socket on which connect(2) had been used to set a destination
                        address.

     [EINVAL]           The iovcnt argument was less than or equal to 0, or greater than IOV_MAX.

     [EINVAL]           One of the iov_len values in the iov array was negative.

     [EINVAL]           The sum of the iov_len values in the iov array overflowed a 32-bit
                        integer.

     [ENOBUFS]          The mbuf pool has been completely exhausted when writing to a socket.

     The pwrite() and pwritev() system calls may also return the following errors:

     [EINVAL]           The offset value was negative.

     [ESPIPE]           The file descriptor is associated with a pipe, socket, or FIFO.

SEE ALSO

     fcntl(2), lseek(2), open(2), pipe(2), select(2)

STANDARDS

     The write() system call is expected to conform to ISO/IEC 9945-1:1990 (“POSIX.1”).  The
     writev() and pwrite() system calls are expected to conform to X/Open Portability Guide
     Issue 4, Version 2 (“XPG4.2”).

HISTORY

     The pwritev() system call appeared in FreeBSD 6.0.  The pwrite() function appeared in AT&T
     System V Release 4 UNIX.  The writev() system call appeared in 4.2BSD.  The write() function
     appeared in Version 1 AT&T UNIX.