oracular (3) assembler.3avr.gz
NAME
assembler - avr-libc and assembler programs
Introduction
There might be several reasons to write code for AVR microcontrollers using plain assembler source code.
Among them are:
• Code for devices that do not have RAM and are thus not supported by the C compiler.
• Code for very time-critical applications.
• Special tweaks that cannot be done in C.
Usually, all but the first could probably be done easily using the inline assembler facility of the
compiler.
Although avr-libc is primarily targeted to support programming AVR microcontrollers using the C (and C++)
language, there's limited support for direct assembler usage as well. The benefits of it are:
• Use of the C preprocessor and thus the ability to use the same symbolic constants that are available to
C programs, as well as a flexible macro concept that can use any valid C identifier as a macro (whereas
the assembler's macro concept is basically targeted to use a macro in place of an assembler
instruction).
• Use of the runtime framework like automatically assigning interrupt vectors. For devices that have RAM,
initializing the RAM variables can also be utilized.
Invoking the compiler
For the purpose described in this document, the assembler and linker are usually not invoked manually,
but rather using the C compiler frontend (avr-gcc) that in turn will call the assembler and linker as
required.
This approach has the following advantages:
• There is basically only one program to be called directly, avr-gcc, regardless of the actual source
language used.
• The invokation of the C preprocessor will be automatic, and will include the appropriate options to
locate required include files in the filesystem.
• The invokation of the linker will be automatic, and will include the appropriate options to locate
additional libraries as well as the application start-up code (crtXXX.o) and linker script.
Note that the invokation of the C preprocessor will be automatic when the filename provided for the
assembler file ends in .S (the capital letter 's'). This would even apply to operating systems that use
case-insensitive filesystems since the actual decision is made based on the case of the filename suffix
given on the command-line, not based on the actual filename from the file system.
As an alternative to using .S, the suffix .sx is recognized for this purpose (starting with GCC 4.3.0).
This is primarily meant to be compatible with other compiler environments that have been providing this
variant before in order to cope with operating systems where filenames are case-insensitive (and, with
some versions of make that could not distinguish between .s and .S on such systems).
Alternatively, the language can explicitly be specified using the -x assembler-with-cpp option.
Example program
The following annotated example features a simple 100 kHz square wave generator using an AT90S1200
clocked with a 10.7 MHz crystal. Pin PD6 will be used for the square wave output.
#include <avr/io.h> ; Note [1]
work = 16 ; Note [2]
tmp = 17
inttmp = 19
intsav = 0
SQUARE = PD6 ; Note [3]
; Note [4]:
tmconst= 10700000 / 200000 ; 100 kHz => 200000 edges/s
fuzz= 8 ; # clocks in ISR until TCNT0 is set
.section .text
.global main ; Note [5]
main:
rcall ioinit
1:
rjmp 1b ; Note [6]
.global TIMER0_OVF_vect ; Note [7]
TIMER0_OVF_vect:
ldi inttmp, 256 - tmconst + fuzz
out _SFR_IO_ADDR(TCNT0), inttmp ; Note [8]
in intsav, _SFR_IO_ADDR(SREG) ; Note [9]
sbic _SFR_IO_ADDR(PORTD), SQUARE
rjmp 1f
sbi _SFR_IO_ADDR(PORTD), SQUARE
rjmp 2f
1: cbi _SFR_IO_ADDR(PORTD), SQUARE
2:
out _SFR_IO_ADDR(SREG), intsav
reti
ioinit:
sbi _SFR_IO_ADDR(DDRD), SQUARE
ldi work, _BV(TOIE0)
out _SFR_IO_ADDR(TIMSK), work
ldi work, _BV(CS00) ; tmr0: CK/1
out _SFR_IO_ADDR(TCCR0), work
ldi work, 256 - tmconst
out _SFR_IO_ADDR(TCNT0), work
sei
ret
.global __vector_default ; Note [10]
__vector_default:
reti
.end
Note [1]
As in C programs, this includes the central processor-specific file containing the IO port definitions
for the device. Note that not all include files can be included into assembler sources.
Note [2]
Assignment of registers to symbolic names used locally. Another option would be to use a C preprocessor
macro instead:
#define work 16
Note [3]
Our bit number for the square wave output. Note that the right-hand side consists of a CPP macro which
will be substituted by its value (6 in this case) before actually being passed to the assembler.
Note [4]
The assembler uses integer operations in the host-defined integer size (32 bits or longer) when
evaluating expressions. This is in contrast to the C compiler that uses the C type int by default in
order to calculate constant integer expressions.
In order to get a 100 kHz output, we need to toggle the PD6 line 200000 times per second. Since we use
timer 0 without any prescaling options in order to get the desired frequency and accuracy, we already run
into serious timing considerations: while accepting and processing the timer overflow interrupt, the
timer already continues to count. When pre-loading the TCCNT0 register, we therefore have to account for
the number of clock cycles required for interrupt acknowledge and for the instructions to reload TCCNT0
(4 clock cycles for interrupt acknowledge, 2 cycles for the jump from the interrupt vector, 2 cycles for
the 2 instructions that reload TCCNT0). This is what the constant fuzz is for.
Note [5]
External functions need to be declared to be .global. main is the application entry point that will be
jumped to from the ininitalization routine in crts1200.o.
Note [6]
The main loop is just a single jump back to itself. Square wave generation itself is completely handled
by the timer 0 overflow interrupt service. A sleep instruction (using idle mode) could be used as well,
but probably would not conserve much energy anyway since the interrupt service is executed quite
frequently.
Note [7]
Interrupt functions can get the usual names that are also available to C programs. The linker will then
put them into the appropriate interrupt vector slots. Note that they must be declared .global in order to
be acceptable for this purpose. This will only work if <avr/io.h> has been included. Note that the
assembler or linker have no chance to check the correct spelling of an interrupt function, so it should
be double-checked. (When analyzing the resulting object file using avr-objdump or avr-nm, a name like
__vector_N should appear, with N being a small integer number.)
Note [8]
As explained in the section about special function registers, the actual IO port address should be
obtained using the macro _SFR_IO_ADDR. (The AT90S1200 does not have RAM thus the memory-mapped approach
to access the IO registers is not available. It would be slower than using in / out instructions anyway.)
Since the operation to reload TCCNT0 is time-critical, it is even performed before saving SREG.
Obviously, this requires that the instructions involved would not change any of the flag bits in SREG.
Note [9]
Interrupt routines must not clobber the global CPU state. Thus, it is usually necessary to save at least
the state of the flag bits in SREG. (Note that this serves as an example here only since actually, all
the following instructions would not modify SREG either, but that's not commonly the case.)
Also, it must be made sure that registers used inside the interrupt routine do not conflict with those
used outside. In the case of a RAM-less device like the AT90S1200, this can only be done by agreeing on a
set of registers to be used exclusively inside the interrupt routine; there would not be any other chance
to 'save' a register anywhere.
If the interrupt routine is to be linked together with C modules, care must be taken to follow the
register usage guidelines imposed by the C compiler. Also, any register modified inside the interrupt
sevice needs to be saved, usually on the stack.
Note [10]
As explained in Interrupts, a global 'catch-all' interrupt handler that gets all unassigned interrupt
vectors can be installed using the name __vector_default. This must be .global, and obviously, should end
in a reti instruction. (By default, a jump to location 0 would be implied instead.)
Pseudo-ops and operators
The available pseudo-ops in the assembler are described in the GNU assembler (gas) manual. The manual can
be found online as part of the current binutils release under http://sources.redhat.com/binutils/.
As gas comes from a Unix origin, its pseudo-op and overall assembler syntax is slightly different than
the one being used by other assemblers. Numeric constants follow the C notation (prefix 0x for
hexadecimal constants), expressions use a C-like syntax.
Some common pseudo-ops include:
• .byte allocates single byte constants
• .ascii allocates a non-terminated string of characters
• .asciz allocates a \0-terminated string of characters (C string)
• .data switches to the .data section (initialized RAM variables)
• .text switches to the .text section (code and ROM constants)
• .set declares a symbol as a constant expression (identical to .equ)
• .global (or .globl) declares a public symbol that is visible to the linker (e. g. function entry point,
global variable)
• .extern declares a symbol to be externally defined; this is effectively a comment only, as gas treats
all undefined symbols it encounters as globally undefined anyway
Note that .org is available in gas as well, but is a fairly pointless pseudo-op in an assembler
environment that uses relocatable object files, as it is the linker that determines the final position of
some object in ROM or RAM.
Along with the architecture-independent standard operators, there are some AVR-specific operators
available which are unfortunately not yet described in the official documentation. The most notable
operators are:
• lo8 Takes the least significant 8 bits of a 16-bit integer
• hi8 Takes the most significant 8 bits of a 16-bit integer
• pm Takes a program-memory (ROM) address, and converts it into a RAM address. This implies a division by
2 as the AVR handles ROM addresses as 16-bit words (e.g. in an IJMP or ICALL instruction), and can also
handle relocatable symbols on the right-hand side.
Example:
ldi r24, lo8(pm(somefunc))
ldi r25, hi8(pm(somefunc))
call something
This passes the address of function somefunc as the first parameter to function something.