Ubuntu Manpage: lirc - lirc devices

NAME

       lirc - lirc devices

DESCRIPTION

       The  /dev/lirc*  character devices provide a low-level bidirectional interface to infra-red (IR) remotes.
       Most of these devices can receive, and some can send.  When receiving or sending data, the  driver  works
       in two different modes depending on the underlying hardware.

       Some  hardware  (typically TV-cards) decodes the IR signal internally and provides decoded button presses
       as scancode values.  Drivers for this kind of hardware work in LIRC_MODE_SCANCODE  mode.   Such  hardware
       usually does not support sending IR signals.  Furthermore, such hardware can only decode a limited set of
       IR protocols, usually only the protocol of the specific remote which is bundled with, for example, a  TV-
       card.

       Other  hardware  provides  a stream of pulse/space durations.  Such drivers work in LIRC_MODE_MODE2 mode.
       Such hardware can be used with (almost) any kind of remote.  This type of hardware can also  be  used  in
       LIRC_MODE_SCANCODE  mode, in which case the kernel IR decoders will decode the IR.  These decoders can be
       written in extended BPF (see bpf(2)) and attached to the lirc device.  Sometimes, this kind  of  hardware
       also supports sending IR data.

       The  LIRC_GET_FEATURES  ioctl  (see below) allows probing for whether receiving and sending is supported,
       and in which modes, amongst other features.

   Reading input with the LIRC_MODE_MODE2 mode
       In the LIRC_MODE_MODE2 mode, the data returned by read(2) provides 32-bit values representing a space  or
       a  pulse duration.  The time of the duration (microseconds) is encoded in the lower 24 bits.  Pulse (also
       known as flash) indicates a duration of infrared light being detected, and  space  (also  known  as  gap)
       indicates  a  duration  with  no  infrared.   If  the duration of space exceeds the inactivity timeout, a
       special timeout package is delivered, which marks the end of a message.  The upper 8  bits  indicate  the
       type of package:

       LIRC_MODE2_SPACE
           Value reflects a space duration (microseconds).

       LIRC_MODE2_PULSE
           Value reflects a pulse duration (microseconds).

       LIRC_MODE2_FREQUENCY
           Value reflects a frequency (Hz); see the LIRC_SET_MEASURE_CARRIER_MODE ioctl.

       LIRC_MODE2_TIMEOUT
           Value   reflects  a  space  duration  (microseconds).   The  package  reflects  a  timeout;  see  the
           LIRC_SET_REC_TIMEOUT_REPORTS ioctl.

       LIRC_MODE2_OVERFLOW
           The IR receiver encountered an overflow, and as a result data is missing (since Linux 5.18).

   Reading input with the LIRC_MODE_SCANCODE mode
       In the LIRC_MODE_SCANCODE mode, the data returned by read(2) reflects  decoded  button  presses,  in  the
       struct  lirc_scancode.   The  scancode  is stored in the scancode field, and the IR protocol is stored in
       rc_proto.  This field has one the values of the enum rc_proto.

   Writing output with the LIRC_MODE_PULSE mode
       The data written to the character device using write(2) is a  pulse/space  sequence  of  integer  values.
       Pulses  and  spaces  are  only  marked  implicitly by their position.  The data must start and end with a
       pulse, thus it must always include an odd number of samples.  The write(2) function blocks until the data
       has  been transmitted by the hardware.  If more data is provided than the hardware can send, the write(2)
       call fails with the error EINVAL.

   Writing output with the LIRC_MODE_SCANCODE mode
       The data written to the character devices must be  a  single  struct  lirc_scancode.   The  scancode  and
       rc_proto  fields  must  filled  in,  all other fields must be 0.  The kernel IR encoders will convert the
       scancode to pulses and spaces.  The protocol or scancode is invalid, or the lirc device cannot transmit.

IOCTL COMMANDS

#include <linux/lirc.h> /* But see BUGS */

int ioctl(int fd, int cmd, int *val);

The following ioctl(2) operations are provided by the lirc character device to probe or change specific
lirc hardware settings.

Always Supported Commands
/dev/lirc* devices always support the following commands:

LIRC_GET_FEATURES (void)
Returns a bit mask of combined features bits; see FEATURES.

If a device returns an error code for LIRC_GET_FEATURES, it is safe to assume it is not a lirc device.

Optional Commands
Some lirc devices support the commands listed below. Unless otherwise stated, these fail with the error
ENOTTY if the operation isn't supported, or with the error EINVAL if the operation failed, or invalid
arguments were provided. If a driver does not announce support of certain features, invoking the
corresponding ioctls will fail with the error ENOTTY.

LIRC_GET_REC_MODE (void)
If the lirc device has no receiver, this operation fails with the error ENOTTY. Otherwise, it
returns the receive mode, which will be one of:

LIRC_MODE_MODE2
The driver returns a sequence of pulse/space durations.

LIRC_MODE_SCANCODE
The driver returns struct lirc_scancode values, each of which represents a decoded button
press.

LIRC_SET_REC_MODE (int)
Set the receive mode. val is either LIRC_MODE_SCANCODE or LIRC_MODE_MODE2. If the lirc device
has no receiver, this operation fails with the error ENOTTY.

LIRC_GET_SEND_MODE (void)
Return the send mode. LIRC_MODE_PULSE or LIRC_MODE_SCANCODE is supported. If the lirc device
cannot send, this operation fails with the error ENOTTY.

LIRC_SET_SEND_MODE (int)
Set the send mode. val is either LIRC_MODE_SCANCODE or LIRC_MODE_PULSE. If the lirc device
cannot send, this operation fails with the error ENOTTY.

LIRC_SET_SEND_CARRIER (int)
Set the modulation frequency. The argument is the frequency (Hz).

LIRC_SET_SEND_DUTY_CYCLE (int)
Set the carrier duty cycle. val is a number in the range [0,100] which describes the pulse width
as a percentage of the total cycle. Currently, no special meaning is defined for 0 or 100, but
the values are reserved for future use.

LIRC_GET_MIN_TIMEOUT(void)
LIRC_GET_MAX_TIMEOUT(void)
Some devices have internal timers that can be used to detect when there has been no IR activity
for a long time. This can help lircd(8) in detecting that an IR signal is finished and can speed
up the decoding process. These operations return integer values with the minimum/maximum timeout
that can be set (microseconds). Some devices have a fixed timeout. For such drivers,
LIRC_GET_MIN_TIMEOUT and LIRC_GET_MAX_TIMEOUT will fail with the error ENOTTY.

LIRC_SET_REC_TIMEOUT (int)
Set the integer value for IR inactivity timeout (microseconds). To be accepted, the value must be
within the limits defined by LIRC_GET_MIN_TIMEOUT and LIRC_GET_MAX_TIMEOUT. A value of 0 (if
supported by the hardware) disables all hardware timeouts and data should be reported as soon as
possible. If the exact value cannot be set, then the next possible value greater than the given
value should be set.

LIRC_GET_REC_TIMEOUT (void)
Return the current inactivity timeout (microseconds). Available since Linux 4.18.

LIRC_SET_REC_TIMEOUT_REPORTS (int)
Enable (val is 1) or disable (val is 0) timeout packages in LIRC_MODE_MODE2. The behavior of this
operation has varied across kernel versions:

• Since Linux 5.17: timeout packages are always enabled and this ioctl is a no-op.

• Since Linux 4.16: timeout packages are enabled by default. Each time the lirc device is
opened, the LIRC_SET_REC_TIMEOUT operation can be used to disable (and, if desired, to later
re-enable) the timeout on the file descriptor.

• In Linux 4.15 and earlier: timeout packages are disabled by default, and enabling them (via
LIRC_SET_REC_TIMEOUT) on any file descriptor associated with the lirc device has the effect of
enabling timeouts for all file descriptors referring to that device (until timeouts are
disabled again).

LIRC_SET_REC_CARRIER (int)
Set the upper bound of the receive carrier frequency (Hz). See LIRC_SET_REC_CARRIER_RANGE.

LIRC_SET_REC_CARRIER_RANGE (int)
Sets the lower bound of the receive carrier frequency (Hz). For this to take affect, first set
the lower bound using the LIRC_SET_REC_CARRIER_RANGE ioctl, and then the upper bound using the
LIRC_SET_REC_CARRIER ioctl.

LIRC_SET_MEASURE_CARRIER_MODE (int)
Enable (val is 1) or disable (val is 0) the measure mode. If enabled, from the next key press on,
the driver will send LIRC_MODE2_FREQUENCY packets. By default, this should be turned off.

LIRC_GET_REC_RESOLUTION (void)
Return the driver resolution (microseconds).

LIRC_SET_TRANSMITTER_MASK (int)
Enable the set of transmitters specified in val, which contains a bit mask where each enabled
transmitter is a 1. The first transmitter is encoded by the least significant bit, and so on.
When an invalid bit mask is given, for example a bit is set even though the device does not have
so many transmitters, this operation returns the number of available transmitters and does nothing
otherwise.

LIRC_SET_WIDEBAND_RECEIVER (int)
Some devices are equipped with a special wide band receiver which is intended to be used to learn
the output of an existing remote. This ioctl can be used to enable (val equals 1) or disable (val
equals 0) this functionality. This might be useful for devices that otherwise have narrow band
receivers that prevent them to be used with certain remotes. Wide band receivers may also be more
precise. On the other hand, their disadvantage usually is reduced range of reception.

Note: wide band receiver may be implicitly enabled if you enable carrier reports. In that case,
it will be disabled as soon as you disable carrier reports. Trying to disable a wide band
receiver while carrier reports are active will do nothing.

FEATURES

the LIRC_GET_FEATURES ioctl returns a bit mask describing features of the driver. The following bits may
be returned in the mask:

LIRC_CAN_REC_MODE2
The driver is capable of receiving using LIRC_MODE_MODE2.

LIRC_CAN_REC_SCANCODE
The driver is capable of receiving using LIRC_MODE_SCANCODE.

LIRC_CAN_SET_SEND_CARRIER
The driver supports changing the modulation frequency using LIRC_SET_SEND_CARRIER.

LIRC_CAN_SET_SEND_DUTY_CYCLE
The driver supports changing the duty cycle using LIRC_SET_SEND_DUTY_CYCLE.

LIRC_CAN_SET_TRANSMITTER_MASK
The driver supports changing the active transmitter(s) using LIRC_SET_TRANSMITTER_MASK.

LIRC_CAN_SET_REC_CARRIER
The driver supports setting the receive carrier frequency using LIRC_SET_REC_CARRIER. Any lirc
device since the drivers were merged in Linux 2.6.36 must have LIRC_CAN_SET_REC_CARRIER_RANGE set
if LIRC_CAN_SET_REC_CARRIER feature is set.

LIRC_CAN_SET_REC_CARRIER_RANGE
The driver supports LIRC_SET_REC_CARRIER_RANGE. The lower bound of the carrier must first be set
using the LIRC_SET_REC_CARRIER_RANGE ioctl, before using the LIRC_SET_REC_CARRIER ioctl to set the
upper bound.

LIRC_CAN_GET_REC_RESOLUTION
The driver supports LIRC_GET_REC_RESOLUTION.

LIRC_CAN_SET_REC_TIMEOUT
The driver supports LIRC_SET_REC_TIMEOUT.

LIRC_CAN_MEASURE_CARRIER
The driver supports measuring of the modulation frequency using LIRC_SET_MEASURE_CARRIER_MODE.

LIRC_CAN_USE_WIDEBAND_RECEIVER
The driver supports learning mode using LIRC_SET_WIDEBAND_RECEIVER.

LIRC_CAN_SEND_PULSE
The driver supports sending using LIRC_MODE_PULSE or LIRC_MODE_SCANCODE

BUGS

       Using  these  devices  requires  the kernel source header file lirc.h.  This file is not available before
       Linux 4.6.  Users of older kernels could use the file bundled in ⟨http://www.lirc.org⟩.

NAME

DESCRIPTION

IOCTL COMMANDS

FEATURES

BUGS

SEE ALSO