NAME

       slapadd - Add entries to a SLAPD database

SYNOPSIS

       /usr/sbin/slapadd  [-b suffix]  [-c]  [-d debug-level]  [-f slapd.conf]  [-F confdir] [-g]
       [-j lineno] [-l ldif-file] [-n dbnum] [-o option[=value]] [-q]  [-s]  [-S SID]  [-u]  [-v]
       [-w]

DESCRIPTION

       Slapadd  is used to add entries specified in LDAP Directory Interchange Format (LDIF) to a
       slapd(8) database.  It opens the given database  determined  by  the  database  number  or
       suffix  and  adds  entries  corresponding to the provided LDIF to the database.  Databases
       configured as subordinate of this one are also updated, unless -g is specified.  The  LDIF
       input is read from standard input or the specified file.

       All  files eventually created by slapadd will belong to the identity slapadd is run as, so
       make sure you either run slapadd with the same identity  slapd(8)  will  be  run  as  (see
       option -u in slapd(8)), or change file ownership before running slapd(8).

       Note:  slapadd  will  also perform the relevant indexing whilst adding the database if any
       are configured. For specific details, please see slapindex(8).

OPTIONS

       -b suffix
              Use the specified suffix to determine which database to add entries to. By default,
              the  first database that supports the requested operation is used. The -b cannot be
              used in conjunction with the -n option.

       -c     enable continue (ignore errors) mode.

       -d debug-level
              enable debugging messages as defined by the specified debug-level; see slapd(8) for
              details.

       -f slapd.conf
              specify an alternative slapd.conf(5) file.

       -F confdir
              specify  a config directory.  If both -f and -F are specified, the config file will
              be read and converted to config directory  format  and  written  to  the  specified
              directory.   If  neither option is specified, an attempt to read the default config
              directory will be made before trying to use the default config  file.  If  a  valid
              config directory exists then the default config file is ignored. If dry-run mode is
              also specified, no conversion will occur.

       -g     disable subordinate gluing.  Only the specified database will be processed, and not
              its glued subordinates (if any).

       -j lineno
              Jump  to  the specified line number in the LDIF file before processing any entries.
              This allows a load that was aborted due to errors in the input LDIF to  be  resumed
              after the errors are corrected.

       -l ldif-file
              Read LDIF from the specified file instead of standard input.

       -n dbnum
              Add  entries  to  the  dbnum-th  database listed in the configuration file.  The -n
              cannot be used in conjunction with the -b option.  To populate the config  database
              slapd-config(5),  use  -n  0 as it is always the first database. It must physically
              exist on the filesystem prior to this, however.

       -o option[=value]
              Specify an option with a(n optional) value.  Possible generic options/values are:

                     syslog=<subsystems>  (see `-s' in slapd(8))
                     syslog-level=<level> (see `-S' in slapd(8))
                     syslog-user=<user>   (see `-l' in slapd(8))

                     schema-check={yes|no}
                     value-check={yes|no}

              The schema-check option toggles schema checking (default on);
              the value-check option toggles value checking (default off).
              The latter is incompatible with -q.

       -q     enable quick (fewer integrity checks) mode.  Does fewer consistency checks
              on the input data, and no consistency checks when writing the database.
              Improves the load time but if any errors or interruptions occur the resulting
              database will be unusable.

       -s     disable schema checking.  This option is intended to be used when loading
              databases containing special objects, such as fractional objects on a
              partial consumer.  Loading normal objects which do not conform to
              schema may result in unexpected and ill behavior.

       -S SID Server ID to use in generated entryCSN.  Also used for contextCSN
              if -w is set as well.  Defaults to 0.

       -u     enable dry-run (don't write to backend) mode.

       -v     enable verbose mode.

       -w     write syncrepl context information.
              After all entries are added, the contextCSN
              will be updated with the greatest CSN in the database.

LIMITATIONS

       Your slapd(8) should not be running  when  you  do  this  to  ensure  consistency  of  the
       database.

       slapadd  may  not provide naming or schema checks.  It is advisable to use ldapadd(1) when
       adding new entries into an existing directory.

EXAMPLES

       To import the entries specified in file ldif into your slapd(8) database give the command:

            /usr/sbin/slapadd -l ldif

SEE ALSO

       ldap(3), ldif(5), slapcat(8), slapindex(8), slapmodify(8), ldapadd(1), slapd(8)

       "OpenLDAP Administrator's Guide" (http://www.OpenLDAP.org/doc/admin/)

ACKNOWLEDGEMENTS

       OpenLDAP   Software   is   developed   and   maintained   by    The    OpenLDAP    Project
       <http://www.openldap.org/>.   OpenLDAP Software is derived from the University of Michigan
       LDAP 3.3 Release.