Provided by: shorewall_5.2.8-6_all 
NAME
tcpri - Shorewall file
SYNOPSIS
/etc/shorewall[6]/tcpri
DESCRIPTION
This file is used to specify the priority of traffic for simple traffic shaping
(TC_ENABLED=Simple in shorewall.conf[1](5)). Beginning with Shorewall 5.2.7, the file
allows ?FORMAT 2 which inserts a SPORT column immediately to the right of the DPORT
column.
The priority band of each packet is determined by the last entry that the packet matches.
If a packet doesn't match any entry in this file, then its priority will be determined by
its TOS field. The default mapping is as follows but can be changed by setting the
TC_PRIOMAP option in shorewall.conf[1](5).
TOS Bits Means Linux Priority BAND
------------------------------------------------------------
0x0 0 Normal Service 0 Best Effort 2
0x2 1 Minimize Monetary Cost 1 Filler 3
0x4 2 Maximize Reliability 0 Best Effort 2
0x6 3 mmc+mr 0 Best Effort 2
0x8 4 Maximize Throughput 2 Bulk 3
0xa 5 mmc+mt 2 Bulk 3
0xc 6 mr+mt 2 Bulk 3
0xe 7 mmc+mr+mt 2 Bulk 3
0x10 8 Minimize Delay 6 Interactive 1
0x12 9 mmc+md 6 Interactive 1
0x14 10 mr+md 6 Interactive 1
0x16 11 mmc+mr+md 6 Interactive 1
0x18 12 mt+md 4 Int. Bulk 2
0x1a 13 mmc+mt+md 4 Int. Bulk 2
0x1c 14 mr+mt+md 4 Int. Bulk 2
0x1e 15 mmc+mr+mt+md 4 Int. Bulk 2
The columns in the file are as follows.
BAND - {1|2|3}
Classifies matching traffic as High Priority (1), Medium Priority (2) or Low Priority
(3). For those interfaces listed in shorewall-tcinterfaces[2](5), Priority 2 traffic
will be deferred so long and there is Priority 1 traffic queued and Priority 3 traffic
will be deferred so long as there is Priority 1 or Priority 2 traffic to send.
PROTO - protocol[,...]
Optional. The name or number of an IPv4 protocol.
Beginning with Shorewall 4.5.12, this column can accept a comma-separated list of
protocols.
DPORT - port [,...]
This column was named PORT prior to Shorewall 5.2.7. Both 'port' and 'dport' may be
used in the alternate input format[3].
Optional. May only be given if the the PROTO is TCP (6), UDP (17), DCCP (33), SCTP
(132) or UDPLITE (136). A list of one or more port numbers or service names from
/etc/services. Port ranges of the form lowport:highport may also be included. In
format 1, packets whose source or destination port matches the specified port(s) are
assigned to the band given in the BAND column.
SPORT - port [,...]
Only present in file format 2. Optional. May only be given if the the PROTO is TCP
(6), UDP (17), DCCP (33), SCTP (132) or UDPLITE (136). A list of one or more port
numbers or service names from /etc/services. Port ranges of the form lowport:highport
may also be included.
ADDRESS - [address]
Optional. The IP or MAC address that the traffic originated from. MAC addresses must
be given in Shorewall format. If this column contains an address, then the PROTO,
PORT(S) and INTERFACE column must be empty ("-").
INTERFACE - [interface]
Optional. The logical name of an interface that traffic arrives from. If given, the
PROTO, PORT(S) and ADDRESS columns must be empty ("-").
Note
INTERFACE classification of packets occurs before classification by
PROTO/PORT(S)/ADDRESS. So it is highly recommended to place entries that specify
INTERFACE at the top of the file so that the rule about last entry matches is
preserved.
HELPER - [helper]
Optional. Names a Netfilter protocol helper module such as ftp, sip, amanda, etc. A
packet will match if it was accepted by the named helper module. You can also append
"-" and a port number to the helper module name (e.g., ftp-21) to specify the port
number that the original connection was made on.
FILES
/etc/shorewall/tcpri
/etc/shorewall6/tcpri
SEE ALSO
https://shorewall.org/configuration_file_basics.htm#Pairs[3]
prio(8), shorewall(8)
NOTES
1. shorewall.conf
https://shorewall.org/manpages/shorewall.conf.html
2. shorewall-tcinterfaces
https://shorewall.org/manpages/shorewall-tcinterfaces.html
3. alternate input format
https://shorewall.org/configuration_file_basics.htm#Pairs