Provided by: funtools_1.4.4-6_amd64 
NAME
funhist - create a 1D histogram of a column (from a FITS binary table or raw event file)
or an image
SYNOPSIS
funhist [\-n⎪\-w⎪\-T] <iname> [column] [[lo:hi:]bins]
OPTIONS
-n # normalize bin value by the width of each bin
-w # specify bin width instead of number of bins in arg3
-T # output in rdb/starbase format (tab separators)
DESCRIPTION
funhist creates a one-dimensional histogram from the specified columns of a FITS Extension
binary table of a FITS file (or from a non-FITS raw event file), or from a FITS image or
array, and writes that histogram as an ASCII table. Alternatively, the program can perform
a 1D projection of one of the image axes.
The first argument to the program is required, and specifies the Funtools file: FITS table
or image, raw event file, or array. If "stdin" is specified, data are read from the
standard input. Use Funtools Bracket Notation to specify FITS extensions, and filters.
For a table, the second argument also is required. It specifies the column to use in
generating the histogram. If the data file is of type image (or array), the column is
optional: if "x" (or "X"), "y" (or "Y") is specified, then a projection is performed over
the x (dim1) or y (dim2) axes, respectively. (That is, this projection will give the same
results as a histogram performed on a table containing the equivalent x,y event rows.) If
no column name is specified or "xy" (or "XY") is specified for the image, then a histogram
is performed on the values contained in the image pixels.
The argument that follows is optional and specifies the number of bins to use in creating
the histogram and, if desired, the range of bin values. For image and table histograms,
the range should specify the min and max data values. For image histograms on the x and y
axes, the range should specify the min and max image bin values. If this argument is
omitted, the number of output bins for a table is calculated either from the TLMIN/TLMAX
headers values (if these exist in the table FITS header for the specified column) or by
going through the data to calculate the min and max value. For an image, the number of
output bins is calculated either from the DATAMIN/DATAMAX header values, or by going
through the data to calculate min and max value. (Note that this latter calculation might
fail if the image cannot be fit in memory.) If the data are floating point (table or
image) and the number of bins is not specified, an arbitrary default of 128 is used.
For binary table processing, the \-w (bin width) switch can be used to specify the width
of each bin rather than the number of bins. Thus:
funhist test.ev pha 1:100:5
means that 5 bins of width 20 are used in the histogram, while:
funhist -w test.ev pha 1:100:5
means that 20 bins of width 5 are used in the histogram.
The data are divvied up into the specified number of bins and the resulting 1D histogram
(or projection) is output in ASCII table format. For a table, the output displays the
low_edge (inclusive) and hi_edge (exclusive) values for the data. For example, a 15\-row
table containing a "pha" column whose values range from \-7.5 to 7.5 can be processed
thus:
[sh] funhist test.ev pha
# data file: /home/eric/data/test.ev
# column: pha
# min,max,bins: -7.5 7.5 15
bin value lo_edge hi_edge
------ --------- --------------------- ---------------------
1 22 -7.50000000 -6.50000000
2 21 -6.50000000 -5.50000000
3 20 -5.50000000 -4.50000000
4 19 -4.50000000 -3.50000000
5 18 -3.50000000 -2.50000000
6 17 -2.50000000 -1.50000000
7 16 -1.50000000 -0.50000000
8 30 -0.50000000 0.50000000
9 16 0.50000000 1.50000000
10 17 1.50000000 2.50000000
11 18 2.50000000 3.50000000
12 19 3.50000000 4.50000000
13 20 4.50000000 5.50000000
14 21 5.50000000 6.50000000
15 22 6.50000000 7.50000000
[sh] funhist test.ev pha 1:6
# data file: /home/eric/data/test.ev
# column: pha
# min,max,bins: 0.5 6.5 6
bin value lo_edge hi_edge
------ --------- --------------------- ---------------------
1 16 0.50000000 1.50000000
2 17 1.50000000 2.50000000
3 18 2.50000000 3.50000000
4 19 3.50000000 4.50000000
5 20 4.50000000 5.50000000
6 21 5.50000000 6.50000000
[sh] funhist test.ev pha 1:6:3
# data file: /home/eric/data/test.ev
# column: pha
# min,max,bins: 0.5 6.5 3
bin value lo_edge hi_edge
------ --------- --------------------- ---------------------
1 33 0.50000000 2.50000000
2 37 2.50000000 4.50000000
3 41 4.50000000 6.50000000
For a table histogram, the \-n(normalize) switch can be used to normalize the bin value by
the width of the bin (i.e., hi_edge\-lo_edge):
[sh] funhist -n test.ev pha 1:6:3
# data file: test.ev
# column: pha
# min,max,bins: 0.5 6.5 3
# width normalization (val/(hi_edge-lo_edge)) is applied
bin value lo_edge hi_edge
------ --------------------- --------------------- ---------------------
1 16.50000000 0.50000000 2.50000000
2 6.16666667 2.50000000 4.50000000
3 4.10000000 4.50000000 6.50000000
This could used, for example, to produce a light curve with values having units of
counts/second instead of counts.
For an image histogram, the output displays the low and high image values (both inclusive)
used to generate the histogram. For example, in the following example, 184 pixels had a
value of 1, 31 had a value of 2, while only 2 had a value of 3,4,5,6, or 7:
[sh] funhist test.fits
# data file: /home/eric/data/test.fits
# min,max,bins: 1 7 7
bin value lo_val hi_val
------ --------------------- --------------------- ---------------------
1 184.00000000 1.00000000 1.00000000
2 31.00000000 2.00000000 2.00000000
3 2.00000000 3.00000000 3.00000000
4 2.00000000 4.00000000 4.00000000
5 2.00000000 5.00000000 5.00000000
6 2.00000000 6.00000000 6.00000000
7 2.00000000 7.00000000 7.00000000
For the axis projection of an image, the output displays the low and high image bins (both
inclusive) used to generate the projection. For example, in the following example, 21
counts had their X bin value of 2, etc.:
[sh] funhist test.fits x 2:7
# data file: /home/eric/data/test.fits
# column: X
# min,max,bins: 2 7 6
bin value lo_bin hi_bin
------ --------------------- --------------------- ---------------------
1 21.00000000 2.00000000 2.00000000
2 20.00000000 3.00000000 3.00000000
3 19.00000000 4.00000000 4.00000000
4 18.00000000 5.00000000 5.00000000
5 17.00000000 6.00000000 6.00000000
6 16.00000000 7.00000000 7.00000000
[sh] funhist test.fits x 2:7:2
# data file: /home/eric/data/test.fits
# column: X
# min,max,bins: 2 7 2
bin value lo_bin hi_bin
------ --------------------- --------------------- ---------------------
1 60.00000000 2.00000000 4.00000000
2 51.00000000 5.00000000 7.00000000
You can use gnuplot or other plotting programs to graph the results, using a script such
as:
#!/bin/sh
sed -e '1,/---- .*/d
/^$/,$d' ⎪ \
awk '\
BEGIN{print "set nokey; set title \"funhist\"; set xlabel \"bin\"; set ylabel \"counts\"; plot \"-\" with boxes"} \
{print $3, $2, $4-$3}' ⎪ \
gnuplot -persist - 1>/dev/null 2>&1
Similar plot commands are supplied in the script funhist.plot:
funhist test.ev pha ... ⎪ funhist.plot gnuplot
SEE ALSO
See funtools(7) for a list of Funtools help pages