Provided by: xen-utils-common_4.4.2-0ubuntu0.14.04.14_all 
NAME
xm - Obsolete xen management user interface
SYNOPSIS
xm subcommand [args]
DESCRIPTION
This program is now superseded by xl, which should be largely backwards-compatible with xm.
The xm program is the main interface for managing Xen guest domains when the obsolete Xend toolstack is
in use. The program can be used to create, pause, and shutdown domains. It can also be used to list
current domains, enable or pin VCPUs, and attach or detach virtual block devices.
The basic structure of every xm command is almost always:
xm subcommand domain-id [OPTIONS]
Where subcommand is one of the subcommands listed below, domain-id is the numeric domain id, or the
domain name (which will be internally translated to domain id), and OPTIONS are subcommand specific
options. There are a few exceptions to this rule in the cases where the subcommand in question acts on
all domains, the entire machine, or directly on the Xen hypervisor. Those exceptions will be clear for
each of those subcommands.
NOTES
All xm operations rely upon the Xen control daemon, aka xend. For any xm commands to run, xend must also
be running. For this reason you should start xend as a service when your system first boots using Xen.
Most xm commands require root privileges to run due to the communications channels used to talk to the
hypervisor. Running as non root will return an error.
Most xm commands act synchronously, except maybe create, shutdown, mem-set and vcpu-set. The fact that
the xm command returned doesn't necessarily mean that the action is complete and you must poll through xm
list periodically to detect that the operation completed.
DOMAIN SUBCOMMANDS
The following subcommands manipulate domains directly. As stated previously, most commands take domain-
id as the first parameter.
console domain-id
Attach to domain domain-id's console. If you've set up your domains to have a traditional log in
console this will look much like a normal text log in screen.
This uses the back end xenconsole service which currently only works for para-virtual domains.
The attached console will perform much like a standard serial console, so running curses based
interfaces over the console is not advised. Vi tends to get very odd when using it over this
interface.
Use the key combination Ctrl+] to detach the domain console.
create configfile [OPTIONS] [vars]..
The create subcommand requires a config file and can optionally take a series of vars that add to or
override variables defined in the config file. See xmdomain.cfg for full details of that file
format, and possible options used in either the configfile or for vars.
configfile can either be an absolute path to a file, or a relative path to a file located in
/etc/xen.
Create will return as soon as the domain is started. This does not mean the guest OS in the domain
has actually booted, or is available for input.
OPTIONS
--help_config
Print the available configuration variables vars. These variables may be used on the command
line or in the configuration file configfile.
-q, --quiet
No console output.
--path
Search path for configuration scripts. The value of PATH is a colon-separated directory list.
-f=FILE, --defconfig=FILE
Use the given Python configuration script. The configuration script is loaded after arguments
have been processed. Each command-line option sets a configuration variable named after its long
option name, and these variables are placed in the environment of the script before it is loaded.
Variables for options that may be repeated have list values. Other variables can be set using
name=value on the command line. After the script is loaded, option values that were not set on
the command line are replaced by the values set in the script.
-F=FILE, --config=FILE
Use the given SXP formatted configuration script. SXP is the underlying configuration format
used by Xen. SXP configuration scripts can be hand-written or generated from Python
configuration scripts, using the -n (dryrun) option to print the configuration. An SXP formatted
configuration file may also be generated for a given domain-id by redirecting the output from the
the xm list --long domain-id to a file.
-n, --dryrun
Dry run - prints the resulting configuration in SXP but does not create the domain.
-x, --xmldryrun
XML dry run - prints the resulting configuration in XML but does not create the domain.
-s, --skipdtd
Skip DTD checking - skips checks on XML before creating. Experimental. Can decrease create time.
-p, --paused
Leave the domain paused after it is created.
-c, --console_autoconnect
Attach console to the domain as soon as it has started. This is useful for determining issues
with crashing domains.
EXAMPLES
with config file
xm create Fedora4
This creates a domain with the file /etc/xen/Fedora4, and returns as soon as it is run.
without config file
xm create /dev/null ramdisk=initrd.img \
kernel=/boot/vmlinuz-2.6.12.6-xenU \
name=ramdisk vif='' vcpus=1 \
memory=64 root=/dev/ram0
This creates the domain without using a config file (more specifically using /dev/null as an
empty config file), kernel and ramdisk as specified, setting the name of the domain to "ramdisk",
also disabling virtual networking. (This example comes from the xm-test test suite.)
delete
Remove a domain from Xend domain management. The xm list command shows the domain names.
destroy domain-id
Immediately terminate the domain domain-id. This doesn't give the domain OS any chance to react, and
is the equivalent of ripping the power cord out on a physical machine. In most cases you will want
to use the shutdown command instead.
domid domain-name
Converts a domain name to a domain id using xend's internal mapping.
domname domain-id
Converts a domain id to a domain name using xend's internal mapping.
dump-core [OPTIONS] domain-id [filename]
Dumps the virtual machine's memory for the specified domain to the filename specified. The dump file
will be written to a distribution specific directory for dump files. Such as: /var/lib/xen/dump or
/var/xen/dump Defaults to dumping the core without pausing the domain if no OPTIONS are specified.
OPTIONS
-L, --live
Dump core without pausing the domain.
-C, --crash
Crash domain after dumping core.
help [--long]
Displays the short help message (i.e. common commands).
The --long option prints out the complete set of xm subcommands, grouped by function.
list [OPTIONS] [domain-id ...]
Prints information about one or more domains. If no domains are specified it prints out information
about all domains.
OPTIONS
-l, --long
The output for xm list is not the table view shown below, but instead presents the data in SXP
format.
--label
Security labels are added to the output of xm list and the lines are sorted by the labels
(ignoring case). See the ACCESS CONTROL SUBCOMMAND section of this man page for more information
about labels.
--state=<state>
Output information for VMs in the specified state.
EXAMPLE
An example format for the list is as follows:
Name ID Mem(MiB) VCPUs State Time(s)
Domain-0 0 98 1 r----- 5068.6
Fedora3 164 128 1 r----- 7.6
Fedora4 165 128 1 ------ 0.6
Mandrake2006 166 128 1 -b---- 3.6
Mandrake10.2 167 128 1 ------ 2.5
Suse9.2 168 100 1 ------ 1.8
Name is the name of the domain. ID the numeric domain id. Mem is the desired amount of memory to
allocate to the domain (although it may not be the currently allocated amount). VCPUs is the number
of virtual CPUs allocated to the domain. State is the run state (see below). Time is the total run
time of the domain as accounted for by Xen.
STATES
The State field lists 6 states for a Xen domain, and which ones the current domain is in.
r - running
The domain is currently running on a CPU.
b - blocked
The domain is blocked, and not running or runnable. This can be caused because the domain is
waiting on IO (a traditional wait state) or has gone to sleep because there was nothing else for
it to do.
p - paused
The domain has been paused, usually occurring through the administrator running xm pause. When
in a paused state the domain will still consume allocated resources like memory, but will not be
eligible for scheduling by the Xen hypervisor.
s - shutdown
FIXME: Why would you ever see this state?
c - crashed
The domain has crashed, which is always a violent ending. Usually this state can only occur if
the domain has been configured not to restart on crash. See xmdomain.cfg for more info.
d - dying
The domain is in process of dying, but hasn't completely shutdown or crashed.
FIXME: Is this right?
NOTES
The Time column is deceptive. Virtual IO (network and block devices) used by domains requires
coordination by Domain0, which means that Domain0 is actually charged for much of the time that a
DomainU is doing IO. Use of this time value to determine relative utilizations by domains is
thus very suspect, as a high IO workload may show as less utilized than a high CPU workload.
Consider yourself warned.
mem-max domain-id mem
Specify the maximum amount of memory the domain is able to use. mem is specified in megabytes.
The mem-max value may not correspond to the actual memory used in the domain, as it may balloon down
its memory to give more back to the OS.
mem-set domain-id mem
Set the domain's used memory using the balloon driver.
Because this operation requires cooperation from the domain operating system, there is no guarantee
that it will succeed. This command will definitely not work unless the domain has the required
paravirt driver.
Warning: There is no good way to know in advance how small of a mem-set will make a domain unstable
and cause it to crash. Be very careful when using this command on running domains.
migrate domain-id host [OPTIONS]
Migrate a domain to another host machine. Xend must be running on other host machine, it must be
running the same version of Xen, it must have the migration TCP port open and accepting connections
from the source host, and there must be sufficient resources for the domain to run (memory, disk,
etc).
Migration is pretty complicated, and has many security implications. Please read the Xen User's
Guide to ensure you understand the ramifications and limitations on migration before attempting it in
production.
OPTIONS
-l, --live
Use live migration. This will migrate the domain between hosts without shutting down the domain.
See the Xen User's Guide for more information.
-r, --resource Mbs
Set maximum Mbs allowed for migrating the domain. This ensures that the network link is not
saturated with migration traffic while attempting to do other useful work.
new configfile [OPTIONS] [vars]...
Adds a domain to Xend domain management.
The new subcommand requires a config file and can optionally take a series of vars that add to or
override variables defined in the config file. See xmdomain.cfg for full details of that file
format, and possible options used in either the configfile or for vars.
configfile can either be an absolute path to a file, or a relative path to a file located in
/etc/xen.
The new subcommand will return without starting the domain. The domain needs to be started using the
xm start command.
OPTIONS
--help_config
Print the available configuration variables vars. These variables may be used on the command
line or in the configuration file configfile.
-q, --quiet
No console output.
--path
Search path for configuration scripts. The value of PATH is a colon-separated directory list.
-f=FILE, --defconfig=FILE
Use the given Python configuration script. The configuration script is loaded after arguments
have been processed. Each command-line option sets a configuration variable named after its long
option name, and these variables are placed in the environment of the script before it is loaded.
Variables for options that may be repeated have list values. Other variables can be set using
name=value on the command line. After the script is loaded, option values that were not set on
the command line are replaced by the values set in the script.
-F=FILE, --config=FILE
Use the given SXP formatted configuration script. SXP is the underlying configuration format
used by Xen. SXP configuration scripts can be hand-written or generated from Python
configuration scripts, using the -n (dryrun) option to print the configuration. An SXP formatted
configuration file may also be generated for a given domain-id by redirecting the output from the
the xm list --long domain-id to a file.
-n, --dryrun
Dry run - prints the resulting configuration in SXP but does not create the domain.
-x, --xmldryrun
XML dry run - prints the resulting configuration in XML but does not create the domain.
-s, --skipdtd
Skip DTD checking - skips checks on XML before creating. Experimental. Can decrease create time.
-p, --paused
Leave the domain paused after it is created.
-c, --console_autoconnect
Attach console to the domain as soon as it has started. This is useful for determining issues
with crashing domains.
pause domain-id
Pause a domain. When in a paused state the domain will still consume allocated resources such as
memory, but will not be eligible for scheduling by the Xen hypervisor.
reboot [OPTIONS] domain-id
Reboot a domain. This acts just as if the domain had the reboot command run from the console. The
command returns as soon as it has executed the reboot action, which may be significantly before the
domain actually reboots.
The behavior of what happens to a domain when it reboots is set by the on_reboot parameter of the
xmdomain.cfg file when the domain was created.
OPTIONS
-a, --all
Reboot all domains.
-w, --wait
Wait for reboot to complete before returning. This may take a while, as all services in the
domain will have to be shut down cleanly.
restore state-file
Build a domain from an xm save state file. See save for more info.
resume domain-name [OPTIONS]
Moves a domain out of the suspended state and back into memory.
OPTIONS
-p, <--paused>
Moves a domain back into memory but leaves the domain in a paused state. The xm unpause
subcommand may then be used to bring it out of the paused state.
save domain-id state-file
Saves a running domain to a state file so that it can be restored later. Once saved, the domain will
no longer be running on the system, thus the memory allocated for the domain will be free for other
domains to use. xm restore restores from this state file.
This is roughly equivalent to doing a hibernate on a running computer, with all the same limitations.
Open network connections may be severed upon restore, as TCP timeouts may have expired.
shutdown [OPTIONS] domain-id
Gracefully shuts down a domain. This coordinates with the domain OS to perform graceful shutdown, so
there is no guarantee that it will succeed, and may take a variable length of time depending on what
services must be shutdown in the domain. The command returns immediately after signally the domain
unless that -w flag is used.
The behavior of what happens to a domain when it reboots is set by the on_shutdown parameter of the
xmdomain.cfg file when the domain was created.
OPTIONS
-a Shutdown all domains. Often used when doing a complete shutdown of a Xen system.
-w Wait for the domain to complete shutdown before returning.
start domain-name [OPTIONS]
Start a Xend managed domain that was added using the xm new command.
OPTIONS
-p, --paused
Do not unpause domain after starting it.
-c, --console_autoconnect
Connect to the console after the domain is created.
suspend domain-name
Suspend a domain to a state file so that it can be later resumed using the xm resume subcommand.
Similar to the xm save subcommand although the state file may not be specified.
sysrq domain-id letter
Send a Magic System Request signal to the domain. For more information on available magic sys req
operations, see sysrq.txt in your Linux Kernel sources.
unpause domain-id
Moves a domain out of the paused state. This will allow a previously paused domain to now be
eligible for scheduling by the Xen hypervisor.
vcpu-set domain-id vcpu-count
Enables the vcpu-count virtual CPUs for the domain in question. Like mem-set, this command can only
allocate up to the maximum virtual CPU count configured at boot for the domain.
If the vcpu-count is smaller than the current number of active VCPUs, the highest number VCPUs will
be hotplug removed. This may be important for pinning purposes.
Attempting to set the VCPUs to a number larger than the initially configured VCPU count is an error.
Trying to set VCPUs to < 1 will be quietly ignored.
Because this operation requires cooperation from the domain operating system, there is no guarantee
that it will succeed. This command will not work with a full virt domain.
vcpu-list [domain-id]
Lists VCPU information for a specific domain. If no domain is specified, VCPU information for all
domains will be provided.
vcpu-pin domain-id vcpu cpus
Pins the the VCPU to only run on the specific CPUs. The keyword all can be used to apply the cpus
list to all VCPUs in the domain.
Normally VCPUs can float between available CPUs whenever Xen deems a different run state is
appropriate. Pinning can be used to restrict this, by ensuring certain VCPUs can only run on certain
physical CPUs.
XEN HOST SUBCOMMANDS
dmesg [-c]
Reads the Xen message buffer, similar to dmesg on a Linux system. The buffer contains informational,
warning, and error messages created during Xen's boot process. If you are having problems with Xen,
this is one of the first places to look as part of problem determination.
OPTIONS
-c, --clear
Clears Xen's message buffer.
info
Print information about the Xen host in name : value format. When reporting a Xen bug, please
provide this information as part of the bug report.
Sample output looks as follows (lines wrapped manually to make the man page more readable):
host : talon
release : 2.6.12.6-xen0
version : #1 Mon Nov 14 14:26:26 EST 2005
machine : i686
nr_cpus : 2
nr_nodes : 1
cores_per_socket : 1
threads_per_core : 1
cpu_mhz : 696
hw_caps : 0383fbff:00000000:00000000:00000040
total_memory : 767
free_memory : 37
xen_major : 3
xen_minor : 0
xen_extra : -devel
xen_caps : xen-3.0-x86_32
xen_scheduler : credit
xen_pagesize : 4096
platform_params : virt_start=0xfc000000
xen_changeset : Mon Nov 14 18:13:38 2005 +0100
7793:090e44133d40
cc_compiler : gcc version 3.4.3 (Mandrakelinux
10.2 3.4.3-7mdk)
cc_compile_by : sdague
cc_compile_domain : (none)
cc_compile_date : Mon Nov 14 14:16:48 EST 2005
xend_config_format : 3
FIELDS
Not all fields will be explained here, but some of the less obvious ones deserve explanation:
hw_caps
A vector showing what hardware capabilities are supported by your processor. This is equivalent
to, though more cryptic, the flags field in /proc/cpuinfo on a normal Linux machine.
free_memory
Available memory (in MB) not allocated to Xen, or any other domains.
xen_caps
The Xen version and architecture. Architecture values can be one of: x86_32, x86_32p (i.e. PAE
enabled), x86_64, ia64.
xen_changeset
The Xen mercurial changeset id. Very useful for determining exactly what version of code your
Xen system was built from.
log Print out the xend log. This log file can be found in /var/log/xend.log.
top Executes the xentop command, which provides real time monitoring of domains. Xentop is a curses
interface, and reasonably self explanatory.
uptime
Prints the current uptime of the domains running.
SCHEDULER SUBCOMMANDS
Xen ships with a number of domain schedulers, which can be set at boot time with the sched= parameter on
the Xen command line. By default credit is used for scheduling.
FIXME: we really need a scheduler expert to write up this section.
sched-credit [ -d domain-id [ -w[=WEIGHT] | -c[=CAP] ] ]
Set credit scheduler parameters. The credit scheduler is a proportional fair share CPU scheduler
built from the ground up to be work conserving on SMP hosts.
Each domain (including Domain0) is assigned a weight and a cap.
PARAMETERS
WEIGHT
A domain with a weight of 512 will get twice as much CPU as a domain with a weight of 256 on a
contended host. Legal weights range from 1 to 65535 and the default is 256.
CAP The cap optionally fixes the maximum amount of CPU a domain will be able to consume, even if the
host system has idle CPU cycles. The cap is expressed in percentage of one physical CPU: 100 is 1
physical CPU, 50 is half a CPU, 400 is 4 CPUs, etc. The default, 0, means there is no upper cap.
NB: Many systems have features that will scale down the computing power of a cpu that is not 100%
utilized. This can be in the operating system, but can also sometimes be below the operating
system in the BIOS. If you set a cap such that individual cores are running at less than 100%,
this may have an impact on the performance of your workload over and above the impact of the cap.
For example, if your processor runs at 2GHz, and you cap a vm at 50%, the power management system
may also reduce the clock speed to 1GHz; the effect will be that your VM gets 25% of the
available power (50% of 1GHz) rather than 50% (50% of 2GHz). If you are not getting the
performance you expect, look at performance and cpufreq options in your operating system and your
BIOS.
sched-sedf period slice latency-hint extratime weight
Set Simple EDF (Earliest Deadline First) scheduler parameters. This scheduler provides weighted CPU
sharing in an intuitive way and uses realtime-algorithms to ensure time guarantees. For more
information see docs/misc/sedf_scheduler_mini-HOWTO.txt in the Xen distribution.
PARAMETERS
period
The normal EDF scheduling usage in nanoseconds
slice
The normal EDF scheduling usage in nanoseconds
FIXME: these are lame, should explain more.
latency-hint
Scaled period if domain is doing heavy I/O.
extratime
Flag for allowing domain to run in extra time.
weight
Another way of setting CPU slice.
EXAMPLES
normal EDF (20ms/5ms):
xm sched-sedf <dom-id> 20000000 5000000 0 0 0
best-effort domains (i.e. non-realtime):
xm sched-sedf <dom-id> 20000000 0 0 1 0
normal EDF (20ms/5ms) + share of extra-time:
xm sched-sedf <dom-id> 20000000 5000000 0 1 0
4 domains with weights 2:3:4:2
xm sched-sedf <d1> 0 0 0 0 2
xm sched-sedf <d2> 0 0 0 0 3
xm sched-sedf <d3> 0 0 0 0 4
xm sched-sedf <d4> 0 0 0 0 2
1 fully-specified (10ms/3ms) domain, 3 other domains share available rest in 2:7:3 ratio:
xm sched-sedf <d1> 10000000 3000000 0 0 0
xm sched-sedf <d2> 0 0 0 0 2
xm sched-sedf <d3> 0 0 0 0 7
xm sched-sedf <d4> 0 0 0 0 3
VIRTUAL DEVICE COMMANDS
Most virtual devices can be added and removed while guests are running. The effect to the guest OS is
much the same as any hotplug event.
BLOCK DEVICES
block-attach domain-id be-dev fe-dev mode [bedomain-id]
Create a new virtual block device. This will trigger a hotplug event for the guest.
OPTIONS
domain-id
The domain id of the guest domain that the device will be attached to.
be-dev
The device in the backend domain (usually domain 0) to be exported. This can be specified as a
physical partition (phy:sda7) or as a file mounted as loopback (file://path/to/loop.iso).
fe-dev
How the device should be presented to the guest domain. It can be specified as either a symbolic
name, such as /dev/hdc, for common devices, or by device id, such as 0x1400 (/dev/hdc device id
in hex).
mode
The access mode for the device from the guest domain. Supported modes are w (read/write) or r
(read-only).
bedomain-id
The back end domain hosting the device. This defaults to domain 0.
EXAMPLES
Mount an ISO as a Disk
xm block-attach guestdomain file://path/to/dsl-2.0RC2.iso /dev/hdc r
This will mount the dsl ISO as /dev/hdc in the guestdomain as a read only device. This will
probably not be detected as a CD-ROM by the guest, but mounting /dev/hdc manually will work.
block-detach domain-id devid [--force]
Detach a domain's virtual block device. devid may be the symbolic name or the numeric device id given
to the device by domain 0. You will need to run xm block-list to determine that number.
Detaching the device requires the cooperation of the domain. If the domain fails to release the
device (perhaps because the domain is hung or is still using the device), the detach will fail. The
--force parameter will forcefully detach the device, but may cause IO errors in the domain.
block-list [-l|--long] domain-id
List virtual block devices for a domain. The returned output is formatted as a list or as an
S-Expression if the --long option was given.
NETWORK DEVICES
network-attach domain-id [script=scriptname] [ip=ipaddr] [mac=macaddr] [bridge=bridge-name]
[backend=bedomain-id]
Creates a new network device in the domain specified by domain-id. It takes the following optional
options:
OPTIONS
script=scriptname
Use the specified script name to bring up the network. Defaults to the default setting in
xend-config.sxp for vif-script.
ip=ipaddr
Passes the specified IP Address to the adapter on creation.
FIXME: this currently appears to be broken. I'm not sure under what circumstances this should
actually work.
mac=macaddr
The MAC address that the domain will see on its Ethernet device. If the device is not specified it
will be randomly generated with the 00:16:3e vendor id prefix.
bridge=bridge-name
The name of the bridge to attach the vif to, in case you have more than one. This defaults to
xenbr0.
backend=bedomain-id
The backend domain id. By default this is domain 0.
network-detach domain-id devid
Removes the network device from the domain specified by domain-id. devid is the virtual interface
device number within the domain (i.e. the 3 in vif22.3).
FIXME: this is currently broken. Network devices aren't completely removed from domain 0.
network-list [-l|--long]> domain-id
List virtual network interfaces for a domain. The returned output is formatted as a list or as an
S-Expression if the --long option was given.
SEE ALSO
xmdomain.cfg(5), xentop(1)
AUTHOR
Sean Dague <sean at dague dot net>
Daniel Stekloff <dsteklof at us dot ibm dot com>
Reiner Sailer <sailer at us dot ibm dot com>
Stefan Berger <stefanb at us dot ibm dot com>
BUGS
4.4.2 2015-03-19 xm(1)