Ubuntu Manpage: irattach - binds the Linux-IrDA stack to a IrDA port

Provided by: irda-utils_0.9.18-12ubuntu1_amd64

NAME

       irattach - binds the Linux-IrDA stack to a IrDA port

SYNOPSIS

       irattach [ <dev> ] [ -s ] [ -d dongle ] [ -v ] [ -h ]

DESCRIPTION

irattach binds the Linux-IrDA stack to an IrDA port. It configures the low level of the
Linux-IrDA stack in the kernel. This step is usually necessary before you (or
applications) can use the higher layer of the IrDA stack.

The irattach command loads the necessary Linux-IrDA driver, which configures the IrDA
hardware, and configures the IrDA stack to operate on the new IrDA port. Multiple IrDA
ports can be activated through multiple irattach commands.

irattach by default uses the irtty driver which connects to the Linux TTY subsystem and
use the standard Linux serial driver. This works well for most machines and
configurations, but limits the baud rate to 115200bps (IrDA SIR mode). The mode of
operation will work with most FIR hardware (as found in laptops - they provide serial
emulation) and most serial dongles (provided the proper dongle type is specified), making
it a safe choice. However, USB dongles and a few FIR hardware don't support serial
emulation and can't be used with the irtty driver.

irattach can also use one of the Linux FIR drivers (including USB dongle drivers) instead
of the irtty driver. Most FIR drivers require proper configuration of module parameters
(this is documented below). FIR drivers allow you to use higher baud rates (generally up
to 4Mbps). In general, Linux FIR support is not as stable and mature, due to lack of time
and documentation.

irattach must be run as root or installed setuid root, as it requires root privileges. If
you have compiled the IrDA stack as modules (recommended), then you will need to edit the
/etc/modules.conf file. See the Infrared-HOWTO for details.

OPTIONS

<dev> : this is the name of a TTY, an IrDA interface or IrDA driver. irattach decides to
use the irtty driver or one of the FIR drivers based on this argument.

• TTY name : this is the serial port to be configured using the irtty driver, such as
/dev/ttyS0. irattach will use the irtty driver, so only SIR will be available. You need
to check your serial configuration or BIOS to know which serial port is the IrDA port
that need to be passed to irattach.

• interface name : this is the device name of an IrDA interface, such as irda0. irattach
will use one of the FIR drivers (including USB dongle drivers). The selected FIR driver
must be loaded prior to the call to irattach, or the proper alias for the device name
must be set in /etc/modules.conf.

• module name : this is the name of an FIR driver module, such as nsc-ircc (see list
below). All new IrDA interfaces created after loading the module will be configured, so
this won't work if the module is already loaded. This feature is still experimental.

-s : starts discovery of remote IrDA devices (note that the form "-s 1" is no longer
supported)

-v : shows version information (this happens, when no option is given, too)

-h : shows help information.

-d dongle : attaches an additional dongle driver to the IrDA port.

You need a dongle driver if you have an infrared device that connects to your computer's
serial port (normal 9-pin serial port connector). These devices are called dongles, and
can currently be used by any SIR driver (IrTTY or irport). This option is not compatible
with FIR drivers, and only works with the irtty and irport drivers.

The currently known (serial) dongles are:

• esi Extended Systems JetEye PC ESI-9680

• tekram Tekram IrMate IR-210B dongle

• actisys ACTiSYS IR-220L dongle

• actisys+ ACTiSYS IR-220L+ dongle

• girbil Greenwich GIrBIL dongle

• litelink Parallax LiteLink dongle & Extended Systems JetEye PC ESI-9680B

• airport N.N.

• old_belkin Belkin (old) SmartBeam dongle or any dongle only capable of 9600 bauds

• ep7211 IR port driver for the Cirrus Logic EP7211 processor (ARM based)

• mcp2120 Dongles based on the MCP2120 (Microchip)

• act200l ACTiSYS Ir-200L dongles

• ma600 Mobile Action ma600 dongles

• toim3232 Vishay/Temic TOIM3232 and TOIM4232 based dongles

FIR DRIVER MODULES

If you are one of the lucky people which have a FIR chipset or USB dongle that is
supported by one of the Linux-IrDA drivers, you can use irattach with the interface name
of the IrDA port to configure. You will need to configure /etc/conf.modules appropriately,
with at least an alias of irda0 to the driver name, or load the driver manually
beforehand.

You don't strictly need to use irattach with FIR drivers, you can use modprobe to load the
driver, ifconfig to bring up the interface and set the various sysctl by hand, but
irattach offer a convenient way to do it.

Of course, you need to know which FIR driver applies to your hardware. You may use
findchip to get information about the FIR chip. If this doesn't help, the Infrared-HOWTO
shows other means to retrieve these data.

Also, you often need to configure the Linux-serial driver to ignore the IrDA port,
otherwise both drivers will conflict. This can usually be done with setserial /dev/ttySx
uart none.

The currently known FIR drivers are:

• ali-ircc ALi FIR Controller Driver for ALi M5123 (options: io, irq, dma). This driver
supports SIR, MIR and FIR (4Mbps) speeds. This chipset is used by e.g.:

The ALi M5123 FIR Controller is embedded in ALi M1543C, M1535, M1535D, M1535+, M1535D
South Bridge.

• irda-usb IrDA-USB device driver, for USB devices/dongles that comply with the official
IrDA-USB class specification. Note: USB 2.0 is not yet tested. (options: qos_mtt_bits
int, description "Minimum Turn Time"). This is used, for e.g.:

ACTiSYS ACT-IR2000U

KC Technology KC-180

Extended Systems XTNDAccess ESI-9685

Note that there is another USB driver for those devices called ir-usb which is NOT
compatible with the IrDA stack and conflict with irda-usb. Because it always loads
first, you have to remove ir-usb completely.

Devices based on the SigmaTel chip are not not compliant with the IrDA-USB class
specification and therfore not supported by this driver.

• nsc-ircc NSC IrDA device driver (options: io, irq, dma, dongle_id, qos_mtt_bits). This
chipset is used by e.g.:

IBM ThinkPad dongle_id=0x09

HP OmniBook 6000 dongle_id=0x08

• sa1100_ir Infrared driver for devices based on the StrongARM SA1100 embedded
microprocessor (options: power_level, tx_lpm). This driver may support FIR on devices
that can do it. This chipset is used by e.g.:

Samsung YOPY, COMPAQ iPAQ, SHARP Zaurus SL5000/5500

• smc-ircc SMC IrCC controller driver (options: ircc_dma, ircc_irq). This chipset is used
by e.g.:

Fujitsu-Siemens Lifebook 635t Sony PCG-505TX

• w83977af_ir Winbond W83977AF IrDA device driver (options: io, irq, qos_mtt_bits). This
chipset is used by e.g.:

Corel NetWinder

• toshoboe Toshiba OBOE IrDA device driver, supports Toshiba Type-O IR chipset. (options:
max_baud). This chipset is used by e.g.:

Toshiba Libretto 100CT., and many more old Toshiba laptops.

• donauboe is a new version of toshoboe and has better FIR support and compability with
the Donauoboe chip http://libxg.free.fr/lib-irda.html (options: ..). This chipset is
used by e.g.:

Toshiba Libretto 100CT., Tecra 8100, Portege 7020 and many more Toshiba laptops.

• vlsi_ir VLSI 82C147 SIR/MIR/FIR device driver This chipset is used by e.g.:

HP Omnibook 800

(options: ..).

• clksrc int, description "clock input source selection"

• ringsize int array (min = 1, max = 2), description "tx, rx ring descriptor size"

• sirpulse int, description "sir pulse width tuning"

• mtt_bits int, description "IrLAP bitfield representing min-turn-time"

EXAMPLES

       Attach  the  IrDA  stack  to  the  second  serial  port (integrated IrDA port using serial
       emulation) and start discovery:

       • irattach /dev/ttyS1 -s

       Attach the IrDA stack to the first serial port where you have an external  ACTiSYS  serial
       dongle and start discovery:

       • irattach /dev/ttyS0 -d actisys+ -s

       Attach the IrDA stack to the first IrDA-USB dongle and start discovery:

       • modprobe irda-usb ; irattach irda0 -s

       Attach the IrDA stack to the NSC FIR (4Mbps) device driver on a Thinkpad laptop:

       • modprobe nsc-ircc dongle_id=0x9 ; irattach irda0 -s.

       Attach the IrDA stack to the NSC FIR (4Mbps) device driver on a Thinkpad laptop:

       • irattach irda0 -s.

         This assume that you have added the following entries to /etc/conf.modules:

         options nsc-ircc dongle_id=0x09

         alias irda0 nsc-ircc

CAVEATS

The following hints are a very short introduction into the configuration of Linux/IrDA. If
this doesn't help read the Linux/IrDA-Tutorial and/or the Infrared-HOWTO . Before
configuring Linux/IrDA make sure whether you want to configure SIR or FIR. It's
recommended to try SIR first, unless your device is not compatible with SIR (for example
USB dongles).

To get the SIR "serial" device have a look into the BIOS. Then run dmesg | grep tty to get
a survey of tty devices supported by your machine. Now try to choose the one, which is
probably the IrDA device and use irattach /dev/ttySx -s.

If you don't succeed with SIR (which seems a rare case) you may try FIR. First look up the
BIOS. Then run findchip to get information about the IrDA controller chip. Use setserial
/dev/ttySx uart none to avoid conflicts with the serial driver. Note: don't use
setserial if you configure SIR. Now you may use irattach.

Finally irdadump should show at least your computer itself. If it doesn't start at the
beginning.

This man page deal only with the low level of the IrDA stack (IrDA ports and IrDA
drivers). After this step is done, you usually need to setup your favorite application to
access the high level IrDA stack (via IrCOMM, IrLPT, IrNET, IrLAN or IrSOCK), which is
documented elsewhere.

This man page doesn't document the usage of the irport driver. The irport driver support
the same hardware as the irtty driver, but is configured like a FIR driver.

DIAGNOSTICS

       This section currently contains the raw error messages from source code only.

       "ioctl(TIOCGETD): %m"

       "irattach: tty: set_disc(%d): %s"

       "tcsetattr: %m"

       "Failed to open %s: %m"

       "Couldn't get device fd flags: %m"

       "Couldn't set device to non-blocking mode: %m"

BUGS

       N.N.

AUTHOR

       This manual page is written by Werner Heuser  <wehe@tuxmobil.org>.  It  is  based  on  the
       READMEs  from  irda-utils  by  the Linux/IrDA Project and the Linux/IrDA-Tutorial.  It was
       subsequently updated and modified by Jean Tourrilhes <jt@hpl.hp.com>.

COPYRIGHT

       Copyright (c) 2001 Werner Heuser Copyright (c) 2002 Jean Tourrilhes

       Permission is granted to copy, distribute and/or modify this document under the  terms  of
       the  GNU  Free Documentation License (GFDL), Version 1.1 or any later version published by
       the Free Software Foundation; with no Invariant Sections,  no  Front-Cover  Texts  and  no
       Back-Cover Texts.

                                           03 July 2006                               IRATTACH(8)