Ubuntu Manpage: repro - repro SIP proxy server

Provided by: repro_1.9.7-4~ubuntu14.04.1_amd64

NAME

       repro - repro SIP proxy server

SYNOPSIS

       repro [OPTIONS...]

DESCRIPTION

       repro is an open-source, free SIP server. SIP is changing the way people communicate using
       the Internet. It is not only about making phone calls over the Net. The SIP  protocol  and
       its extensions defines the way of establishing, modifying and ending interactive sessions,
       no matter if they are voice, video, IM or a combination of  them.  At  the  heart  of  SIP
       architecture,  there  are certain services which needs to be provided at some place of the
       network.  repro provides SIP proxy, registrar,  redirect,  and  identity  services.  These
       services are the foundation needed to run a SIP service.

OPTIONS

-l, --log-type=cout|syslog|cerr
Set where to send logging messages. The default cout sends the messages to standard
output, cerr uses the standard error pipe. With syslog the messages are send to
the system log using the logging facility local6. See syslogd(8) or syslog.conf(5)
for more information.

-v, --log-level=STACK|DEBUG|INFO|WARNING|ALERT
Set the minimum level a logging message needs to have in order to by written. The
severity rises from left to right in the above order. The default is to log
messages with level INFO or above.

-r, --record-route=sip:example.com
Activate record routing. The argument is the URI used in the Record-Route header
field.

--udp=5060
Specify the port to use for the UDP transport. Set to 0 to turn UDP off. Defaults
to port 5060.

--tcp=5060
Specify the port to use for the TCP transport. Set to 0 to turn TCP off. Defaults
to port 5060.

-t, --tls-domain=example.com
Act as a TLS server for specified domain.

--tls=5061
Set the port to use for the TLS transport. Set to 0 to turn TLS off. Defaults to
port 5061.

--dtls=0
Set the port to use for the DTLS transport. Set to 0 to turn DTLS off which is the
default.

--enable-cert-server
Run a cert server.

-c, --cert-path=STRING
Set the path for certificates. Defaults to ~/.sipCerts.

--enable-v6
Enable IPv6.

--disable-v4
Disable IPv4.

--disable-auth
Disable DIGEST challenges for certain SIP requests.

--disable-web-auth
Disable authentication for the web administration server.

--disable-reg
Disable the registrar.

-i, --interfaces=sip:10.1.1.1:5065;transport=tls
Specify interfaces to add transports to. Each transport is given as a SIP-URI with
the IP address and port of the local interface as the hostport part and the
transport protocol as a transport parameter. Several transports are separated by a
comma.

For example, to set up two transports, one for TLS and one for UDP use
sip:192.168.1.200:5060;transport=tls,sip:192.168.1.200:5060;transport=udp

-d, --domains=example.com,foo.com
Specify the list of domains this proxy is authorative for separated by comma.

-R, --route=sip:p1.example.com,sip:p2.example.com
Specify a route set where all requests this proxy is authorative for are sent to.
Using this option overides the routes set through the web interface.

--reqChainName=STRING
Name of request chain used for processing requests. Currently, the only chain
available is default.

--http=5080
Specify the port used by the HTTP server. Defaults to 5080.

--recursive-redirect
Enable to handle of 3xx responses in the proxy.

--q-value
Enable q-value processing. The q-value can be given in registrations and is used by
the location server to order forwarding for multiple registrations. Without this
option a request is forked to all registrations.

--q-value-behavior=FULL_SEQUENTIAL|EQUAL_Q_PARALLEL|FULL_PARALLEL
Specify forking behavior if --q-value is given. With FULL_SEQUENTIAL one target is
called after another in the order of their q values. Using EQUAL_Q_PARALLEL (the
default), the request is sent in batches of all registrations with the same q
value. The batches are again ordered by the q value. FULL_PARALLEL causes the
request to be sent in parallel to all registrations.

--q-value-cancel-btw-fork-groups
If given, groups of parallel forks are canceled after the period specified by the
--q-value-ms-before-cancel option if no response was received.

--q-value-wait-for-terminate-btw-fork-groups
If given, the proxy waits for groups of parallel forks to terminate before a new
group is started. Otherwise, the next group is started once the waiting time has
passed.

--q-value-ms-between-fork-groups=INT
Specify the number of milliseconds to wait for a response from a group of parallel
forks before starting another group.

--q-value-ms-before-cancel=INT
Specify the number of milliseconds to wait before cancelling a group of parallel
forks if the --q-value-cancel-btw-fork-groups option is given.

-e, --enum-suffix=e164.arpa
Specify enum suffix to search.

-b, --allow-bad-reg
Allow To tag in registrations.

--timer-C=180
Specify the length of timer C in sec which specifies the time a proxy waits before
generating a timeout response. Set to 0 or a negative value to turn timer C of
completely.

--admin-password=STRING
Set the web administrator password.

Help options:

-?, --help
Show a help message.

--usage
Display brief usage message.

--version
Display the version information.

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

SEE ALSO