Provided by: systemd_229-4ubuntu21.31_amd64 bug


       journald.conf, journald.conf.d - Journal service configuration files







       These files configure various parameters of the systemd journal service, systemd-


       The default configuration is defined during compilation, so a configuration file is only
       needed when it is necessary to deviate from those defaults. By default, the configuration
       file in /etc/systemd/ contains commented out entries showing the defaults as a guide to
       the administrator. This file can be edited to create local overrides.

       When packages need to customize the configuration, they can install configuration snippets
       in /usr/lib/systemd/*.conf.d/. Files in /etc/ are reserved for the local administrator,
       who may use this logic to override the configuration files installed by vendor packages.
       The main configuration file is read before any of the configuration directories, and has
       the lowest precedence; entries in a file in any configuration directory override entries
       in the single configuration file. Files in the *.conf.d/ configuration subdirectories are
       sorted by their filename in lexicographic order, regardless of which of the subdirectories
       they reside in. If multiple files specify the same option, the entry in the file with the
       lexicographically latest name takes precedence. It is recommended to prefix all filenames
       in those subdirectories with a two-digit number and a dash, to simplify the ordering of
       the files.

       To disable a configuration file supplied by the vendor, the recommended way is to place a
       symlink to /dev/null in the configuration directory in /etc/, with the same filename as
       the vendor configuration file.


       All options are configured in the "[Journal]" section:

           Controls where to store journal data. One of "volatile", "persistent", "auto" and
           "none". If "volatile", journal log data will be stored only in memory, i.e. below the
           /run/log/journal hierarchy (which is created if needed). If "persistent", data will be
           stored preferably on disk, i.e. below the /var/log/journal hierarchy (which is created
           if needed), with a fallback to /run/log/journal (which is created if needed), during
           early boot and if the disk is not writable.  "auto" is similar to "persistent" but the
           directory /var/log/journal is not created if needed, so that its existence controls
           where log data goes.  "none" turns off all storage, all log data received will be
           dropped. Forwarding to other targets, such as the console, the kernel log buffer, or a
           syslog socket will still work however. Defaults to "auto".

           Takes a boolean value. If enabled (the default), data objects that shall be stored in
           the journal and are larger than a certain threshold are compressed before they are
           written to the file system.

           Takes a boolean value. If enabled (the default), and a sealing key is available (as
           created by journalctl(1)'s --setup-keys command), Forward Secure Sealing (FSS) for all
           persistent journal files is enabled. FSS is based on Seekable Sequential Key
           Generators[1] by G. A. Marson and B. Poettering (doi:10.1007/978-3-642-40203-6_7) and
           may be used to protect journal files from unnoticed alteration.

           Controls whether to split up journal files per user. One of "uid", "login" and "none".
           If "uid", all users will get each their own journal files regardless of whether they
           possess a login session or not, however system users will log into the system journal.
           If "login", actually logged-in users will get each their own journal files, but users
           without login session and system users will log into the system journal. If "none",
           journal files are not split up by user and all messages are instead stored in the
           single system journal. Note that splitting up journal files by user is only available
           for journals stored persistently. If journals are stored on volatile storage (see
           above), only a single journal file for all user IDs is kept. Defaults to "uid".

       RateLimitInterval=, RateLimitBurst=
           Configures the rate limiting that is applied to all messages generated on the system.
           If, in the time interval defined by RateLimitInterval=, more messages than specified
           in RateLimitBurst= are logged by a service, all further messages within the interval
           are dropped until the interval is over. A message about the number of dropped messages
           is generated. This rate limiting is applied per-service, so that two services which
           log do not interfere with each other's limits. Defaults to 1000 messages in 30s. The
           time specification for RateLimitInterval= may be specified in the following units:
           "s", "min", "h", "ms", "us". To turn off any kind of rate limiting, set either value
           to 0.

       SystemMaxUse=, SystemKeepFree=, SystemMaxFileSize=, SystemMaxFiles=, RuntimeMaxUse=,
       RuntimeKeepFree=, RuntimeMaxFileSize=, RuntimeMaxFiles=
           Enforce size limits on the journal files stored. The options prefixed with "System"
           apply to the journal files when stored on a persistent file system, more specifically
           /var/log/journal. The options prefixed with "Runtime" apply to the journal files when
           stored on a volatile in-memory file system, more specifically /run/log/journal. The
           former is used only when /var is mounted, writable, and the directory /var/log/journal
           exists. Otherwise, only the latter applies. Note that this means that during early
           boot and if the administrator disabled persistent logging, only the latter options
           apply, while the former apply if persistent logging is enabled and the system is fully
           booted up.  journalctl and systemd-journald ignore all files with names not ending
           with ".journal" or ".journal~", so only such files, located in the appropriate
           directories, are taken into account when calculating current disk usage.

           SystemMaxUse= and RuntimeMaxUse= control how much disk space the journal may use up at
           most.  SystemKeepFree= and RuntimeKeepFree= control how much disk space
           systemd-journald shall leave free for other uses.  systemd-journald will respect both
           limits and use the smaller of the two values.

           The first pair defaults to 10% and the second to 15% of the size of the respective
           file system, but each value is capped to 4G. If the file system is nearly full and
           either SystemKeepFree= or RuntimeKeepFree= are violated when systemd-journald is
           started, the limit will be raised to the percentage that is actually free. This means
           that if there was enough free space before and journal files were created, and
           subsequently something else causes the file system to fill up, journald will stop
           using more space, but it will not be removing existing files to reduce the footprint
           again, either.

           SystemMaxFileSize= and RuntimeMaxFileSize= control how large individual journal files
           may grow at most. This influences the granularity in which disk space is made
           available through rotation, i.e. deletion of historic data. Defaults to one eighth of
           the values configured with SystemMaxUse= and RuntimeMaxUse=, so that usually seven
           rotated journal files are kept as history.

           Specify values in bytes or use K, M, G, T, P, E as units for the specified sizes
           (equal to 1024, 1024², ... bytes). Note that size limits are enforced synchronously
           when journal files are extended, and no explicit rotation step triggered by time is

           SystemMaxFiles= and RuntimeMaxFiles= control how many individual journal files to keep
           at most. Note that only archived files are deleted to reduce the number of files until
           this limit is reached; active files will stay around. This means that, in effect,
           there might still be more journal files around in total than this limit after a
           vacuuming operation is complete. This setting defaults to 100.

           The maximum time to store entries in a single journal file before rotating to the next
           one. Normally, time-based rotation should not be required as size-based rotation with
           options such as SystemMaxFileSize= should be sufficient to ensure that journal files
           do not grow without bounds. However, to ensure that not too much data is lost at once
           when old journal files are deleted, it might make sense to change this value from the
           default of one month. Set to 0 to turn off this feature. This setting takes time
           values which may be suffixed with the units "year", "month", "week", "day", "h" or "m"
           to override the default time unit of seconds.

           The maximum time to store journal entries. This controls whether journal files
           containing entries older then the specified time span are deleted. Normally,
           time-based deletion of old journal files should not be required as size-based deletion
           with options such as SystemMaxUse= should be sufficient to ensure that journal files
           do not grow without bounds. However, to enforce data retention policies, it might make
           sense to change this value from the default of 0 (which turns off this feature). This
           setting also takes time values which may be suffixed with the units "year", "month",
           "week", "day", "h" or " m" to override the default time unit of seconds.

           The timeout before synchronizing journal files to disk. After syncing, journal files
           are placed in the OFFLINE state. Note that syncing is unconditionally done immediately
           after a log message of priority CRIT, ALERT or EMERG has been logged. This setting
           hence applies only to messages of the levels ERR, WARNING, NOTICE, INFO, DEBUG. The
           default timeout is 5 minutes.

       ForwardToSyslog=, ForwardToKMsg=, ForwardToConsole=, ForwardToWall=
           Control whether log messages received by the journal daemon shall be forwarded to a
           traditional syslog daemon, to the kernel log buffer (kmsg), to the system console, or
           sent as wall messages to all logged-in users. These options take boolean arguments. If
           forwarding to syslog is enabled but nothing reads messages from the socket, forwarding
           to syslog has no effect. By default, only forwarding to syslog and wall is enabled.
           These settings may be overridden at boot time with the kernel command line options
           "systemd.journald.forward_to_syslog=", "systemd.journald.forward_to_kmsg=",
           "systemd.journald.forward_to_console=", and "systemd.journald.forward_to_wall=". When
           forwarding to the console, the TTY to log to can be changed with TTYPath=, described

       MaxLevelStore=, MaxLevelSyslog=, MaxLevelKMsg=, MaxLevelConsole=, MaxLevelWall=
           Controls the maximum log level of messages that are stored on disk, forwarded to
           syslog, kmsg, the console or wall (if that is enabled, see above). As argument, takes
           one of "emerg", "alert", "crit", "err", "warning", "notice", "info", "debug", or
           integer values in the range of 0–7 (corresponding to the same levels). Messages equal
           or below the log level specified are stored/forwarded, messages above are dropped.
           Defaults to "debug" for MaxLevelStore= and MaxLevelSyslog=, to ensure that the all
           messages are written to disk and forwarded to syslog. Defaults to "notice" for
           MaxLevelKMsg=, "info" for MaxLevelConsole=, and "emerg" for MaxLevelWall=.

           Change the console TTY to use if ForwardToConsole=yes is used. Defaults to


       Journal events can be transferred to a different logging daemon in two different ways.
       With the first method, messages are immediately forwarded to a socket
       (/run/systemd/journal/syslog), where the traditional syslog daemon can read them. This
       method is controlled by the ForwardToSyslog= option. With a second method, a syslog daemon
       behaves like a normal journal client, and reads messages from the journal files, similarly
       to journalctl(1). With this, messages do not have to be read immediately, which allows a
       logging daemon which is only started late in boot to access all messages since the start
       of the system. In addition, full structured meta-data is available to it. This method of
       course is available only if the messages are stored in a journal file at all. So it will
       not work if Storage=none is set. It should be noted that usually the second method is used
       by syslog daemons, so the Storage= option, and not the ForwardToSyslog= option, is
       relevant for them.


       systemd(1), systemd-journald.service(8), journalctl(1), systemd.journal-fields(7),


        1. Seekable Sequential Key Generators