Provided by: ptpd_2.3.1-debian1-1_amd64 
NAME
ptpd - Precision Time Protocol daemon (1588-2008)
SYNOPSIS
ptpd [ -?hH ] [ -e SETTING ] [ -kvOLAl ] [ -smMyEPanCV ] [ -c FILE ] [ -R DIR ] [ -f FILE ] [ -S FILE ] [
-d DOMAIN ] [ -u ADDRESS ] [ -r NUMBER ] -i INTERFACE
DESCRIPTION
PTPd is a daemon that implements the Precision Time Protocol (PTP) Version 2 as defined by the IEEE
1588-2008 standard. PTP was developed to provide very precise time coordination of LAN connected
computers. The daemon must run as root in order to be able to manipluate the system clock and use low
port numbers. PTPd is feature rich, supports IPv4 multicast, unicast and hybrid mode (mixed) operation,
as well as Ethernet mode. Even without hardware assistance, PTPd is able to achieve and maintain sub-
microsecond level timing precision and is able to withstand PTP Grandmaster failovers, link failures and
restarts with minimal impact to timing performance. PTPd is lightweight, portable and currently supports
Linux, FreeBSD and Mac OS X and runs on multiple CPU architectures, 32-bit and 64-bit, including x86 and
ARM.
COMMAND-LINE CONFIGURATION
As of version 2.3.0, configuration file is the preferred mechanism for configuring PTPd, therefore the
options available as short (-x) and long options (--xxxxx) mostly provide basic control over the daemon
operation, and only provide the very basic PTP protocol settings. The rest of the settings (see
ptpd2.conf(5)) can also be specified as command-line options, but they take the long
--key:section="value" form.
BASIC DAEMON OPTIONS
-c --config-file PATH
Path to configuration file (see ptpd2.conf(5))
-k --check-config
Check configuration and exit - return 0 if configuration is correct.
-v --version
Print version string and exit
-h --help
Show help screen
-H --long-help
Show detailed help for all settings and behaviours
-e --explain SETTING
Show help for a single setting (section:key)
-O --default-config
Show default configuration and exit (output usable as a configuration file)
-L --ignore-lock
Skip lock file checks and locking (also global:ignore_lock)
-A --auto-lock
Use preset / port mode specific lock file names - useful when running multiple instances
-l --lockfile
Specify lock file path (also global:lock_file)
-p --print-lockfile
Print path to lock file and exit (useful for init scripts in combination with auto lock files)
-R --lock-directory DIR
Directory to store lock files (also global:lock_directory)
-f --log-file PATH
Path to log file (also global:logfile)
-S --statistics-file PATH
Path to statistics file (also global:statistics_file)
BASIC PTP PROTOCOL OPTIONS
-i --interface DEV
REQUIRED:Interface to use - eth0, etc (also ptpengine:interface)
-d --domain NUMBER
PTP domain number to become part of (also ptpengine:domain)
-s --slaveonly
Slave only mode (also ptpengine:preset=slaveonly)
-m --masterslave
Full IEEE 1588 implementation: master, slave when not best GM (also ptpengine:preset=masterslave)
-M --masteronly
Master only mode: passive when not best GM (also ptpengine:preset=masteronly)
-y --hybrid
Hybrid mode - mixed multicast and unicast operation (multicast for sync and announce, unicast for
delay request and response (also ptpengine:ip_mode=hybrid)
-U --unicast
Unicast operation - (also ptpengine:ip_mode=unicast). For a GM, unicast destinations must be
specified (-u, --unicast-destinations, ptpengine:unicast_destinations) unless using unicast
negotiation (-g, --unicast-negotiation, ptpengine:unicast_negotiation=y) for delay request and
response (also ptpengine:ip_mode=hybrid). For a slave, unicast destinations must be specified if
not using unicast negotiation.
-g --unicast-negotiation
Enable unicast message delivery and interval negotiation usin signaling messages, as used by the
Telecom profile (also enables ptpengine:ip_mode=unicast)
-u --unicast-destinations ip/host, ip/host, ...
List of unicast destinations - see --unicast (also ptpengine:ip_mode=unicast +
ptpengine:unicast_destinations) -E --e2e End to end delay mechanism (also
ptpengine:delay_mechanism=E2E)
-E --p2p
Peer to peer delay mechanism (also ptpengine:delay_mechanism=P2P)
-a --delay-override
In slave state, override delay request interval announced by master (also
ptpengine:log_delayreq_override) - the value of ptpengine:log_delayreq_interval is used
-r --delay-interval NUMBER
Specify delay request message interval (log 2) - (also ptpengine:log_delayreq_interval)
-n --clock:no_adjust
Do not adjust the clock (also clock:no_adjust)
-D<DD...> --debug
Debug level (also global:debug_level) - only if compiled with RUNTIME_DEBUG
-C --foreground
Don't run in background (also global:foreground=Y)
-V --verbose
Run in foreground, log all the messages to standard output (also global:verbose_foreground=Y)
COMPATIBILITY OPTIONS
PTPd supports the following options compatible with versions before 2.3.0:
-b DEV Network interface to use
-i NUMBER
PTP domain number
-g Slave only mode
-G ´Master mode with NTP´ (master only mode)
-W ´Master mode without NTP´ (master / slave mode)
-U Hybrid mode (mixed unicast + multicast operation)
-Y NUMBER
Delay request interval (log 2)
-t Do not adjust the clock
NOTE: the above options are deprecated and will be removed in subsequent versions. Until then, their use
will issue a warning.
PTPD PORT STATES
init INITIALIZING
flt FAULTY
lstn_init
LISTENING (first time)
lstn_reset
LISTENING (subsequent reset)
pass PASSIVE (not best master, not announcing)
uncl UNCALIBRATED
slv SLAVE
pmst PRE-MASTER
mst MASTER (active)
dsbl DISABLED
? (unk)
UNKNOWN state
STATISTICS LOG FILE FORMAT
When the statistics log is enabled (ptpengine:log_statistics, verbose foreground mode or log file -
ptpengine:statistics_file), a PTPd slave will log clock sync information upon the receipt of every Sync
and Delay Response message. When PTPd starts up or flushes the log, a comment line (starting with #)
will be logged, containing the names of all columns. The format of this log is a series of comma-
separated values (CSV) and can be easily imported into statistics tools and most spreadsheet software
packages for analysis and graphing. This log can get very large when running PTPd for longer periods of
time and with high message rates, therefore to reduce the number of messages logged, the
global:statistics_log_interval setting can be used, to limit the log output to one message per configured
interval only. The size and maximum number of the statistics log can also be controlled - (see
ptpd2.conf(5)).
The meaning of the columns is as follows:
Timestamp
Time when message received. This can take the form of text date / time or Unix timestamp
(with fractional seconds), or both (in which case an exra field is added), depending
onthe global:statistics_timestamp_format setting (see ptpd2.conf(5)). When importing the
log into plotting software, if the software can understand Unix time, it is best to set
the timestamp format to unix or both, as some software will not properly deal with the
fractional part of the second when converting the date and time from text.
State Port state (see PTP PORT STATES).
Clock ID
Port identity of the current best master, as defined by IEEE 1588. This will be the local
clock's ID if the local clock is the best master. Displayed as clock_id/port(host) Port
is the PTP clock port number, not to be confused with UDP ports. The clock ID is an
EUI-64 64-bit ID, usually converted from the 48-bit MAC address, by inserting 0xfffe
between the lower and upper half of the MAC address. PTPd will attempt to convert the
clock ID back to MAC address and look up the hostname from /etc/ethers (see ethers(5)).
Populating the ethers file will help the administrator recognise the masters by familiar
hostnames.
One Way Delay
Current value of one-way delay (or mean path delay) in seconds, calculated by PTPd in
slave state from the Delay Request - Delay Response message exchange. Note: if this value
remains at zero, this usually means that no Delay Response messages are being received,
likely due to a network issue.
Offset From Master
Current value of offset from master in seconds - this is the main output of the PTP
engine in slave state, which is the input of the clock servo for clock corrections. This
is the value typically observed when estimating the slave performance.
Slave to Master
Intermediate offset value (seconds) extracted from the Delay Request - Delay Response
message exchange, used for computing one-way delay. If the last value was rejected by a
filter, the previous value will be shown in the log. This value will also be zero if no
Delay Response messages are being received.
Master to Slave
Intermediate offset value (seconds) extracted from the Sync messages, used for computing
the offset from master. If the last value was rejected by a filter, the previous value
will be shown in the log.
Observed Drift
The integral accumulator of the clock control PI servo model - frequency difference
between the slave clock and master clock. This value becomes stable when the clock offset
has stabilised, and can be used (and is) to detect clock stability.
Last Packet Received
This field shows what message was received last - this will be S for Sync and D for Delay
Response. If a slave logs no D entries, this means it's not receiving Delay Response
messages, which could be a network issue.
One Way Delay Mean
One-way delay mean computed over the last sampling window.
One Way Delay Std Dev
One-way delay standard deviation computed over the last sampling window.
Offset From Master Mean
Offset from master mean computed over the last sampling window.
Offset From Master Std Dev
Offset from master standard deviation computed over the last sampling window.
Observed Drift Mean
Observed drift / local clock frequency adjustment mean computed over the last sampling
window.
Observed Drift Std Dev
Observed drift / local clock frequency adjustment standard deviation computed over the
last sampling window. The lower the value, the less aggressively the clock is being
controlled and therefore the more stable it is.
raw delayMS
Raw (unfiltered) delayMS value - useful for evaluating outliers and filter performance.
raw delaySM
Raw (unfiltered) delaySM value - useful for evaluating outliers and filter performance.
NOTE: All the statistical measures (mean and std dev) will only be computed and displayed if PTPd was
built without --disable-statistics. The duration of the sampling period is controlled with the
global:statistics_update_interval setting - (see ptpd2.conf(5)).
HANDLED SIGNALS
PTPd handles the following signals:
SIGHUP Reload configuration file (if used) and reopen log files
SIGUSR1 When in slave state, force clock step to current Offset from Master value
SIGUSR2 Dump all PTP protocol counters to current log target (and clear if
ptpengine:sigusr2_clears_counters set)
SIGINT|SIGTERM
Clean exit - close logs and other open files, clean up lock file and exit.
SIGKILL Force an unclean exit.
EXIT CODES
Upon exit, ptpd2 returns 0 on success - either successfully started in daemon mode, or otherwise exited
cleanly. 0 is also returned when the -k (--check-config) option is used and the configuration was
correct. A non-zero exit code is returned on errors. 3 is returned on lock file errors and when ptpd2
could not be started as daemon. 2 is returned on memory allocation errors during startup. For all other
error conditions such as configuration errors, running ptpd2 in help mode or with no parameters, on self
shutdown, network startup errors and when attempting to run ptpd2 as non-root - 1 is returned.
SUPPORTED PLATFORMS AND ARCHITECTURES
PTPd is fully supported on Linux and FreeBSD as this is what the core developers focus on. OpenBSD and
NetBSD are also supported, but get less developers' attention. So is Max OS X, and as of PTPd 2.3.1 also
OpenSolaris (11) derivatives (tested on OmniOS). Sun's / Oracle's Solaris 11 has not been tested but in
essence, it should work as intended. Solaris 10 is NOT supported because it does not provide the
SO_TIMESTAMP socket option. It should theoretically be possible to use Solaris 10 using the pf facility
as used by snoop, but there is currently no ongoing effort to acheive this. Patches for QNX/Neutrino have
been provided, but cannot yet officially be merged because of no availability of QNX to the developers.
Some users have ported PTPd to other RTOS, but this has not been merged either.
As of 2.3.1, PTPd runs entirely in software and only relies on kernel and OS APIs, so there are no
hardware dependencies. Any little-endian or big-endian port of modern versions of the supported OSes
should work, but only x86 and ARM are actively tested. The only dependencies close to hardware can be NIC
drivers and how and if they impact software timestamping.
HARDWARE TIMESTAMPING SUPPORT
As of 2.3.1, PTPd still does not support hardware timestamping. This functionality will appear in the
upcoming version 2.4 - potentially an interim version of 2.3.x may be delivered that will support
hardware clocks and timestamping on Linux. This is very much OS-specific and to a large extent, hardware-
specific. Linux has a PTP kernel API but not all hardware supports it. Because PTPd supports multiple OS
platforms, where hardware timestamping may use different mechanisms on every platform, it has to be re-
written in a modular way to allow this without unnecessarily increasing code complexity, which already is
a problem.
BUGS
As of ptpd 2.3.1, the (Open)Solaris (11) OS family is supported, but libpcap functionality is currently
broken - IPv4/pcap and Ethernet transports cannot be used on those systems. PTPd will compile and run,
but will not receive any data.
Please report any bugs using the bug tracker on the SourceForge page:
http://sourceforge.net/projects/ptpd/
SEE ALSO
ptpd2.conf(5)
AUTHORS
Gael Mace <gael_mace@users.sourceforge.net>
Alexandre Van Kempen
Steven Kreuzer <skreuzer@freebsd.org>
George Neville-Neil <gnn@freebsd.org>
Wojciech Owczarek <wojciech@owczarek.co.uk>
ptpd2(8) man page was written by Wojciech Owczarek for ptpd 2.3.0 in November 2013
version 2.3.1 June, 2015 ptpd(8)