Provided by: liblopsub-dev_1.0.3-2_amd64 
NAME
lopsub-suite - lopsub suite syntax
DESCRIPTION
A lopsub suite describes the options to a command line utility with zero or more related subcommands. The
lopsubgen(1) utility translates a lopsub suite into either C source code or a manual page. The generated
C code can be compiled and linked against the lopsub library to produce command line parsers for the main
command and all subcommands defined in the suite.
This document explains the format of a lopsub suite. The overall structure is as follows:
[suite mysuite]
suite directives
[supercommand sup_cmd]
command directives for sup_cmd
[option opt1]
... (further options)
[subcommand sub1]
command directives for sub1
[option opt_1_to_sub1]
option directives for opt_1
... (further options)
... (further subcommands)
[section see also]
... (optional extra section for man page)
... (further extra sections)
A suite begins with a [suite] line which declares the name of the suite. The suite directives, all
subsequent lines up to the first [supercommand] or [subcommand] line, state further properties of the
suite which are unrelated to any particular command, for example the version number. All available suite
directives are summarized below.
The [supercommand] and [subcommand] lines indicate the beginning of a command of the suite. The part
between this line and the first [option] line contains the command directives, for example the purpose
and the description of the named command. See the section on command directives below.
Supercommands and subcommands share the same set of possible command directives. They differ mainly in
the way the documentation is formated. There can only be one supercommand but arbitrary many subcommands.
For example, the supercommand could be the name of the application, and the subcommands could be "load",
"save" "info" and "quit". The subcommand would be passed as the first non-option argument to the
supercommand, followed by options specific to that subcommand.
Of course it is possible to define no subcommands at all. Conversely, one can define only subcommands but
no supercommand. This makes sense if the commands are run by some other means, for example in an
interactive session from a command prompt.
Within the command section, an [option] line starts an option to the current command. It is followed by
option directives, which specify, for example, whether or not the option takes an argument. All supported
option directives are listed in the corresponding section below.
Further material for man output can be included between the [section] and [/section] markers. This text
will not be included in the generated .c and .h files and is thus also not part of the short and long
help available at run time. The text is not interpreted except that leading whitespace is stripped from
each line. Arbitrary roff source can be included here.
Empty lines and lines starting with a hash character (#) are ignored.
SUITE DIRECTIVES
Most directives of this section are only relevant for man page output (with aux_info_default being the
exception), they are ignored for C output.
caption
The optional text for an unnumbered section heading at the beginning of the manual page.
title Sets the title of the man page. Defaults to the name of the supercommand. If this is not given and
the suite has no supercommand, the .TH macro to set the title of the man page is omitted.
mansect
Sets the man page section. Defaults to 1 (user commands). Both title and section are positioned at
the left and right in the header line.
date This text is positioned in the middle of the footer line of the man page. It is common to set this
to the date of the last nontrivial change that was made to the man page. Defaults to the current
date.
version-string
Positioned at the left in the footer line. Defaults to the empty string. The value of this
directive is ignored if a version string is explicitly requested by passing --version-string to
losubgen.
manual_title
Centered in the header line. Defaults to "User commands".
introduction
conclusion
The text enclosed between [introduction] and [/introduction] is shown between the supercommand (if
any) and the subcommand list. Concluding remarks after the subcommand list may be added in the
same way with [conclusion] and [/conclusion]. Both texts will become part of the manual page, but
are not not part of the short or long help. Like for the section directive, arbitrary roff source
may be included here.
aux_info_prefix
This text is shown at the bottom of each command before the value of the aux_info directive. If no
aux_info is specified for a command, the prefix is omitted as well. If aux_info_prefix is not
given, the empty string is assumed.
aux_info_default
This text is only used for header output. The argument for the generated macro call is set to
this value for all commands for which no aux_info directive is given. If no aux_info_default
directive is given, the value 0 is used as the argument for the macro.
COMMAND DIRECTIVES
purpose
A single line containing the purpose of the command. This text is printed in the short and long
help, and is also included in the man page.
description
closing
Arbitrary plain text enclosed between [description] and [/description]. The text may be split
over multiple lines and paragraphs. The description of the supercommand (if any) becomes the
description of the manual page, which is shown after the command summary and before the list of
options. The descriptions of all commands are included in the manual page and in the long help
text but not in the short help.
Closing remarks for the command can be added in a similar way by enclosing plain text between
[closing] and [/closing]. This text will be positioned after the option list.
synopsis
Custom synopsis of the command. If this is not given, the synopsis text will be auto-generated
from the options and the value of the non-opts-name directive.
non-opts-name
Name of the command line arguments which are not related to any option, for example file names.
This text will be included in the automatically generated synopsis text.
If this is not given, the command is assumed to take no arguments other than the specified options
and their arguments. For such commands the attempt to parse an argv[] vector fails if it contains
further non-option arguments.
aux_info
This directive is special because its value is not included in the generated .c file but in the
header file. More precisely, the preprocessor macro LSG_SUITENAME_AUX_INFOS will be defined which
expands to a series of macro calls to LSG_SUITENAME_AUX_INFO(val_n), one for each command of the
suite, where val_n is the (unquoted) value of the aux_info directive of the nth command. Commands
for which no aux_info directive was specified receive a value of zero. The LSG_SUITENAME_AUX_INFO
macro is supposed to be defined by the application. Hence it is up to the application to make the
expansion of LSG_SUITENAME_AUX_INFOS a valid C construct.
The value, if specified, is also copied to the man page at the end of the section for the command.
OPTION DIRECTIVES
short_opt
The optional single-letter equivalent for the option. If this is specified, the option may be
given either in the GNU-style long option format with two leading dashes or in the short form with
a single dash. Otherwise only the long form will be accepted. As usual, multiple short option
flags may be combined.
summary
A single line which summarizes the option. This text is included in both the short and the long
help and in the man page. Defaults to the empty string.
typestr
A description for the type of the values for the option. The given text is printed in the synopsis
of the command, which is part of the short and the long help and the man page. It defaults to the
string "val".
This directive is ignored for flag options (options without an argument).
arg_info
This directive determines whether the option takes an argument. The possible values are no_arg,
required_arg and optional_arg which indicate, respectively, that the option takes no argument at
all, an argument which is mandatory, or an argument which may be omitted. The default value is
no_arg. Hence an option works as a flag if the arg_info directive is not given.
Note that arguments to options which take an optional argument must be given as --foo=bar rather
than --foo bar because the latter form would be ambiguous.
arg_type
For flag options this directive should be set to none, or not set at all. For options which take
an argument, the value of the directive determines the type of the argument. Possible values are
string for options which take a string argument, and int32, uint32. int64, uint64, for options
which take a numeric argument.
flag Lopsub maintains for each option a bitmask which contains the value of each possible flag for this
option. Flags may be accumulated by defining multiple flag directives in the suite. Note there is
no equal sign between the flag directive and its value.
The following flags are defined.
multiple
This flag instructs the lopsub library to keep track of all given arguments to an option,
not just one as for ordinary options. This is only relevant for options which take an
(optional or required) argument.
required
Instruct the parser to fail if this option is not given in the argument vector. If an
option may be given at the command line or in the config file, this flag should be avoided
because the command line argv vector will not be parsed successfully if the option is only
given in the config file. The recommended way to deal with this situation is to parse
command line and config file separately, then merge the two parse results and check in the
application if the option is given in the merged parse result.
There is another disadvantage of this flag: if the parser fails due to a missing option
that was declared required, it is not possible to detect if other options were given. For
example, if the suite defines the --help option, and the application is executed with this
option only, the parser will still return a parse error.
ignored
This flag indicates that the current option is in fact not a real option. In particular,
name and short_opt are both ignored. The purpose of this flag is to add additional
information for the help output and the man page.
values Create an enumerable option.
Enumerable options take one out of a fixed set of possible values which are predefined in the
suite. Such options are always of type string. It is an error if a different argument type was
specified or if the option was defined to not take an argument.
The syntax for the array of values is
values = {ID_0 = "string_0", ..., ID_N = "string_N"}
For each option for which the values directive was specified, the lopsubgen command generates a C
enumeration which contains the given identifiers. This allows referring to each possible value
through a numeric constant.
default_val
This directive makes only sense for options which take an argument. For such options it defines
the value the option parser provides automatically if the option is not given in the argument
vector.
If no default_val is specified in the suite, and the option is not given in the argument vector
either, the implied value depends on the argument type. For numeric options, a value of zero is
assumed. For options which take a string argument, a NULL pointer is returned. For enum options,
the first possible value (index zero) is taken as the default.
help The detailed, multi-line help text for the current option. Included in the man page and the long
help.
EXAMPLE
A minimal suite and the corresponding "application".
The suite file hello.suite:
[suite hello]
[supercommand hello]
purpose = hello world
[option world]
summary = add "world"
The "application" hello.c:
#include <stdio.h> /* printf(3) */
#include <stdlib.h> /* exit(3) */
#include <lopsub.h>
#include "hello.lsg.h"
int main(int argc, char **argv)
{
struct lls_parse_result *lpr;
const struct lls_opt_result *result;
const struct lls_command *cmd = lls_cmd(0, hello_suite);
int ret;
ret = lls_parse(argc, argv, cmd, &lpr, NULL);
if (ret < 0) {
fprintf(stderr, "%s\n", lls_strerror(-ret));
exit(1);
}
printf("hello");
result = lls_opt_result(LSG_HELLO_HELLO_OPT_WORLD, lpr);
if (lls_opt_given(result))
printf(" world");
printf("\n");
exit(0);
}
Generate hello.lsg.c and hello.lsg.h:
$ lopsubgen --gen-c --gen-h < hello.suite
Compile hello.c and hello.lsg.c to produce the hello executable:
$ cc hello.c hello.lsg.c -o hello -llopsub
Run it:
$ ./hello
hello
$ ./hello --world
hello world
$ ./hello -w
option not recognized
$ ./hello 42
invalid number of arguments
Generate and examine the manual page:
$ lopsubgen --gen-man < hello.suite
$ man -l ./hello.lsg.man
SEE ALSO
lopsubgen(1), lopsub(7), lopsubex(1), gengetopt(1), getopt(1), getopt(3)