Provided by: sg3-utils_1.46-3ubuntu4_amd64 
NAME
sg3_utils - a package of utilities for sending SCSI commands
SYNOPSIS
sg_* [--dry-run] [--enumerate] [--help] [--hex] [--in=FN] [--inhex=FN] [--maxlen=LEN] [--raw]
[--timeout=SECS] [--verbose] [--version] [OTHER_OPTIONS] DEVICE
DESCRIPTION
sg3_utils is a package of utilities that send SCSI commands to the given DEVICE via a SCSI pass through
interface provided by the host operating system.
The names of all utilities start with "sg" and most start with "sg_" often followed by the name, or a
shortening of the name, of the SCSI command that they send. For example the "sg_verify" utility sends the
SCSI VERIFY command. A mapping between SCSI commands and the sg3_utils utilities that issue them is shown
in the COVERAGE file. The sg_raw utility can be used to send an arbitrary SCSI command (supplied on the
command line) to the given DEVICE.
sg_decode_sense can be used to decode SCSI sense data given on the command line or in a file. sg_raw -vvv
will output the T10 name of a given SCSI CDB which is most often 16 bytes or less in length.
SCSI draft standards can be found at http://www.t10.org . The standards themselves can be purchased from
ANSI and other standards organizations. A good overview of various SCSI standards can be seen in
http://www.t10.org/scsi-3.htm with the SCSI command sets in the upper part of the diagram. The highest
level (i.e. most abstract) document is the SCSI Architecture Model (SAM) with SAM-5 being the most recent
standard (ANSI INCITS 515-2016) with the most recent draft being SAM-6 revision 4 . SCSI commands in
common with all device types can be found in SCSI Primary Commands (SPC) of which SPC-4 is the most
recent standard (ANSI INCITS 513-2015). The most recent SPC draft is SPC-5 revision 21. Block device
specific commands (e.g. as used by disks) are in SBC, those for tape drives in SSC, those for SCSI
enclosures in SES and those for CD/DVD/BD drives in MMC.
It is becoming more common to control ATA disks with the SCSI command set. This involves the translation
of SCSI commands to their corresponding ATA equivalents (and that is an imperfect mapping in some cases).
The relevant standard is called SCSI to ATA Translation (SAT, SAT-2 and SAT-3) are now standards at
INCITS(ANSI) and ISO while SAT-4 is at the draft stage. The logic to perform the command translation is
often called a SAT Layer or SATL and may be within an operating system, in host bus adapter firmware or
in an external device (e.g. associated with a SAS expander). See http://www.t10.org for more information.
There is some support for SCSI tape devices but not for their basic operation. The reader is referred to
the "mt" utility.
There are two generations of command line option usage. The newer utilities (written since July 2004) use
the getopt_long() function to parse command line options. With that function, each option has two
representations: a short form (e.g. '-v') and a longer form (e.g. '--verbose'). If an argument is
required then it follows a space (optionally) in the short form and a "=" in the longer form (e.g. in the
sg_verify utility '-l 2a6h' and '--lba=2a6h' are equivalent). Note that with getopt_long(), short form
options can be elided, for example: '-all' is equivalent to '-a -l -l'. The DEVICE argument may appear
after, between or prior to any options.
The older utilities, including as sg_inq, sg_logs, sg_modes, sg_opcode, sg_rbuff, sg_readcap,
sg_senddiag, sg_start and sg_turs had individual command line processing code typically based on a single
"-" followed by one or more characters. If an argument is needed then it follows a "=" ( e.g. '-p=1f' in
sg_modes with its older interface). Various options can be elided as long as it is not ambiguous (e.g.
'-vv' to increase the verbosity).
Over time the command line interface of these older utilities became messy and overloaded with options.
So in sg3_utils version 1.23 the command line interface of these older utilities was altered to have both
a cleaner getopt_long() interface and their older interface for backward compatibility. By default these
older utilities use their getopt_long() based interface. The getopt_long() is a GNU extension (i.e. not
yet POSIX certified) but more recent command line utilities tend to use it. That can be overridden by
defining the SG3_UTILS_OLD_OPTS environment variable or using '-O' or '--old' as the first command line
option. The man pages of the older utilities documents the details.
Several sg3_utils utilities are based on the Unix dd command (e.g. sg_dd) and permit copying data at the
level of SCSI READ and WRITE commands. sg_dd is tightly bound to Linux and hence is not ported to other
OSes. A more generic utility (than sg_dd) called ddpt in a package of the same name has been ported to
other OSes.
ENVIRONMENT VARIABLES
The SG3_UTILS_OLD_OPTS environment variable is explained in the previous section. It is only for backward
compatibility of the command line options for older utilities.
The SG3_UTILS_DSENSE environment variable may be set to a number. It is only used by the embedded SNTL
within the library used by the utilities in this library. SNTL is a SCSI to NVMe Translation Layer. This
environment variable defaults to 0 which will lead to any utility that issues a SCSI command that is
translated to a NVMe command (by the embedded SNTL) that fails at the NVMe dvice, to return SCSI sense in
'fixed' format. If this variable is non-zero then then the returned SCSI sense will be in 'descriptor'
format.
Several utilities have their own environment variable setting (e.g. sg_persist has
SG_PERSIST_IN_RDONLY). See individual utility man pages for more information.
There is a Linux specific environment variable called SG3_UTILS_LINUX_NANO that if defined and the sg
driver in the system is 4.0.30 or later, will show command durations in nanoseconds rather than the
default milliseconds. Command durations are typically only shown if --verbose is used 3 or more times.
Due to an interface problem (a 32 bit integer that should be 64 bits with the benefit of hindsight) the
maximum duration that can be represented in nanoseconds is about 4.2 seconds. If longer durations may
occur then don't define this environment variable (or undefine it).
LINUX DEVICE NAMING
Most disk block devices have names like /dev/sda, /dev/sdb, /dev/sdc, etc. SCSI disks in Linux have
always had names like that but in recent Linux kernels it has become more common for many other disks
(including SATA disks and USB storage devices) to be named like that. Partitions within a disk are
specified by a number appended to the device name, starting at 1 (e.g. /dev/sda1 ).
Tape drives are named /dev/st<num> or /dev/nst<num> where <num> starts at zero. Additionally one letter
from this list: "lma" may be appended to the name. CD, DVD and BD readers (and writers) are named
/dev/sr<num> where <num> start at zero. There are less used SCSI device type names, the dmesg and the
lsscsi commands may help to find if any are attached to a running system.
There is also a SCSI device driver which offers alternate generic access to SCSI devices. It uses names
of the form /dev/sg<num> where <num> starts at zero. The "lsscsi -g" command may be useful in finding
these and which generic name corresponds to a device type name (e.g. /dev/sg2 may correspond to
/dev/sda). In the lk 2.6 series a block SCSI generic driver was introduced and its names are of the form
/dev/bsg/<h:c:t:l> where h, c, t and l are numbers. Again see the lsscsi command to find the
correspondence between that SCSI tuple (i.e. <h:c:t:l>) and alternate device names.
Prior to the Linux kernel 2.6 series these utilities could only use generic device names (e.g. /dev/sg1
). In almost all cases in the Linux kernel 2.6 series, any device name can be used by these utilities.
Very little has changed in Linux device naming in the Linux kernel 3 and 4 series.
WINDOWS DEVICE NAMING
Storage and related devices can have several device names in Windows. Probably the most common in the
volume name (e.g. "D:"). There are also a "class" device names such as "PhysicalDrive<n>", "CDROM<n>" and
"TAPE<n>". <n> is an integer starting at 0 allocated in ascending order as devices are discovered (and
sometimes rediscovered).
Some storage devices have a SCSI lower level device name which starts with a SCSI (pseudo) adapter name
of the form "SCSI<n>:". To this is added sub-addressing in the form of a "bus" number, a "target"
identifier and a LUN (Logical Unit Number). The "bus" number is also known as a "PathId". These are
assembled to form a device name of the form: "SCSI<n>:<bus>,<target>,<lun>". The trailing ",<lun>" may be
omitted in which case a LUN of zero is assumed. This lower level device name cannot often be used
directly since Windows blocks attempts to use it if a class driver has "claimed" the device. There are
SCSI device types (e.g. Automation/Drive interface type) for which there is no class driver. At least
two transports ("bus types" in Windows jargon): USB and IEEE 1394 do not have a "scsi" device names of
this form.
In keeping with DOS file system conventions, the various device names can be given in upper, lower or
mixed case. Since "PhysicalDrive<n>" is tedious to write, a shortened form of "PD<n>" is permitted by all
utilities in this package.
A single device (e.g. a disk) can have many device names. For example: "PD0" can also be "C:", "D:" and
"SCSI0:0,1,0". The two volume names reflect that the disk has two partitions on it. Disk partitions that
are not recognized by Windows are not usually given a volume name. However Vista does show a volume name
for a disk which has no partitions recognized by it and when selected invites the user to format it
(which may be rather unfriendly to other OSes).
These utilities assume a given device name is in the Win32 device namespace. To make that explicit
"\\.\" can be prepended to the device names mentioned in this section. Beware that backslash is an escape
character in Unix like shells and the C programming language. In a shell like Msys (from MinGW) each
backslash may need to be typed twice.
The sg_scan utility within this package lists out Windows device names in a form that is suitable for
other utilities in this package to use.
FREEBSD DEVICE NAMING
SCSI disks have block names of the form /dev/da<num> where <num> is an integer starting at zero. The "da"
is replaced by "sa" for SCSI tape drives and "cd" for SCSI CD/DVD/BD drives. Each SCSI device has a
corresponding pass-through device name of the form /dev/pass<num> where <num> is an integer starting at
zero. The "camcontrol devlist" command may be useful for finding out which SCSI device names are
available and the correspondence between class and pass-through names.
FreeBSD allows device names to be given without the leading "/dev/" (e.g. da0 instead of /dev/da0). That
worked in this package up until version 1.43 when the unadorned device name (e.g. "da0") gave an error.
The original action (i.e. allowing unadorned device names) has been restored in version 1.46 . Also note
that symlinks (to device names) are followed before prepending "/dev/" if the resultant name doesn't
start with a "/".
SOLARIS DEVICE NAMING
SCSI device names below the /dev directory have a form like: c5t4d3s2 where the number following "c" is the controller (HBA) number, the number following "t" is the target number (from the SCSI parallel interface days) and the number following "d" is the LUN. Following the "s" is the slice number which is related to a partition and by convention "s2" is the whole disk. OpenSolaris also has a c5t4d3p2 form where the number following the "p" is the partition number apart from "p0" which is the whole disk. So a whole disk may be referred to as either c5t4d3, c5t4d3s2 or c5t4d3p0 . And these device names are duplicated in the /dev/dsk and /dev/rdsk directories. The former is the block device name and the latter is for "raw" (or char device) access which is what sg3_utils needs. So in OpenSolaris something of the form 'sg_inq /dev/rdsk/c5t4d3p0' should work. If it doesn't work then add a '-vvv' option for more debug information. Trying this form 'sg_inq /dev/dsk/c5t4d3p0' (note "rdsk" changed to "dsk") will result in an "inappropriate ioctl for device" error. The device names within the /dev directory are typically symbolic links to much longer topological names in the /device directory. In Solaris cd/dvd/bd drives seem to be treated as disks and so are found in the /dev/rdsk directory. Tape drives appear in the /dev/rmt directory. There is also a sgen (SCSI generic) driver which by default does not attach to any device. See the /kernel/drv/sgen.conf file to control what is attached. Any attached device will have a device name of the form /dev/scsi/c5t4d3 . Listing available SCSI devices in Solaris seems to be a challenge. "Use the 'format' command" advice works but seems a very dangerous way to list devices. [It does prompt again before doing any damage.] 'devfsadm -Cv' cleans out the clutter in the /dev/rdsk directory, only leaving what is "live". The "cfgadm -v" command looks promising.
NVME SUPPORT
NVMe (or NVM Express) is a relatively new storage transport and command set. The level of abstraction of
the NVMe command set is somewhat lower the SCSI command sets, closer to the level of abstraction of ATA
(and SATA) command sets. NVMe claims to be designed with flash and modern "solid state" storage in mind,
something unheard of when SCSI was originally developed in the 1980s.
The SCSI command sets' advantage is the length of time they have been in place and the existing tools
(like these) to support it. Plus SCSI command sets level of abstraction is both and advantage and
disadvantage. Recently the NVME-MI (Management Interface) designers decide to use the SCSI Enclosure
Services (SES-3) standard "as is" with the addition of two tunnelling NVME-MI commands: SES Send and SES
Receive. This means after the OS interface differences are taken into account, the sg_ses,
sg_ses_microcode and sg_senddiag utilities can be used on a NVMe device that supports a newer version of
NVME-MI.
The NVME-MI SES Send and SES Receive commands correspond to the SCSI SEND DIAGNOSTIC and RECEIVE
DIAGNOSTIC RESULTS commands respectively. There are however a few other commands that need to be
translated, the most important of which is the SCSI INQUIRY command to the NVMe Identify
controller/namespace. Starting in version 1.43 these utilities contain a small SNTL (SCSI to NVMe
Translation Layer) to take care of these details.
As a side effect of this "juggling" if the sg_inq utility is used (without the --page= option) on a NVMe
DEVICE then the actual NVMe Identifier (controller and possibly namespace) responses are decoded and
output. However if 'sg_inq --page=sinq <device>' is given for the same DEVICE then parts of the NVMe
Identify controller and namespace response are translated to a SCSI standard INQUIRY response which is
then decoded and output.
Apart from the special case with the sg_inq, all other utilities in the package assume they are talking
to a SCSI device and decode any response accordingly. One easy way for users to see the underlying device
is a NVMe device is the standard INQUIRY response Vendor Identification field of "NVMe " (an 8
character long string with 4 spaces to the right).
The following SCSI commands are currently supported by the SNTL library: INQUIRY, MODE SELECT(10), MODE
SENSE(10), READ(10,16), READ CAPACITY(10,16), RECEIVE DIAGNOSTIC RESULTS, REQUEST SENSE, REPORT LUNS,
REPORT SUPPORTED OPERATION CODES, REPORT SUPPORTED TASK MANAGEMENT FUNCTIONS, SEND DIAGNOSTICS, START
STOP UNIT, SYNCHRONIZE CACHE(10,16), TEST UNIT READY, VERIFY(10,16), WRITE(10,16) and WRITE SAME(10,16).
EXIT STATUS
To aid scripts that call these utilities, the exit status is set to indicate success (0) or failure (1 or
more). Note that some of the lower values correspond to the SCSI sense key values.
The exit status values listed below can be given to the sg_decode_sense utility (which is found in this
package) as follows:
sg_decode_sense --err=<exit_status>
and a short explanatory string will be output to stdout.
The exit status values are:
0 success. Also used for some utilities that wish to return a boolean value for the "true" case (and
that no error has occurred). The false case is conveyed by exit status 36.
1 syntax error. Either illegal command line options, options with bad arguments or a combination of
options that is not permitted.
2 the DEVICE reports that it is not ready for the operation requested. The DEVICE may be in the
process of becoming ready (e.g. spinning up but not at speed) so the utility may work after a
wait. In Linux the DEVICE may be temporarily blocked while error recovery is taking place.
3 the DEVICE reports a medium or hardware error (or a blank check). For example an attempt to read a
corrupted block on a disk will yield this value.
5 the DEVICE reports an "illegal request" with an additional sense code other than "invalid command
operation code". This is often a supported command with a field set requesting an unsupported
capability. For commands that require a "service action" field this value can indicate that the
command with that service action value is not supported.
6 the DEVICE reports a "unit attention" condition. This usually indicates that something unrelated
to the requested command has occurred (e.g. a device reset) potentially before the current SCSI
command was sent. The requested command has not been executed by the device. Note that unit
attention conditions are usually only reported once by a device.
7 the DEVICE reports a "data protect" sense key. This implies some mechanism has blocked writes (or
possibly all access to the media).
9 the DEVICE reports an illegal request with an additional sense code of "invalid command operation
code" which means that it doesn't support the requested command.
10 the DEVICE reports a "copy aborted". This implies another command or device problem has stopped a
copy operation. The EXTENDED COPY family of commands (including WRITE USING TOKEN) may return this
sense key.
11 the DEVICE reports an aborted command. In some cases aborted commands can be retried immediately
(e.g. if the transport aborted the command due to congestion).
14 the DEVICE reports a miscompare sense key. VERIFY and COMPARE AND WRITE commands may report this.
15 the utility is unable to open, close or use the given DEVICE or some other file. The given file
name could be incorrect or there may be permission problems. Adding the '-v' option may give more
information.
17 a SCSI "Illegal request" sense code received with a flag indicating the Info field is valid. This
is often a LBA but its meaning is command specific.
18 the DEVICE reports a medium or hardware error (or a blank check) with a flag indicating the Info
field is valid. This is often a LBA (of the first encountered error) but its meaning is command
specific.
20 the DEVICE reports it has a check condition but "no sense" and non-zero information in its
additional sense codes. Some polling commands (e.g. REQUEST SENSE) can receive this response.
There may be useful information in the sense data such as a progress indication.
21 the DEVICE reports a "recovered error". The requested command was successful. Most likely a
utility will report a recovered error to stderr and continue, probably leaving the utility with an
exit status of 0 .
22 the DEVICE reports that the current command or its parameters imply a logical block address (LBA)
that is out of range. This happens surprisingly often when trying to access the last block on a
storage device; either a classic "off by one" logic error or a misreading of the response from
READ CAPACITY(10 or 16) in which the address of the last block rather than the number of blocks on
the DEVICE is returned. Since LBAs are origin zero they range from 0 to n-1 where n is the number
of blocks on the DEVICE, so the LBA of the last block is one less than the total number of blocks.
24 the DEVICE reports a SCSI status of "reservation conflict". This means access to the DEVICE with
the current command has been blocked because another machine (HBA or SCSI "initiator") holds a
reservation on this DEVICE. On modern SCSI systems this is related to the use of the PERSISTENT
RESERVATION family of commands.
25 the DEVICE reports a SCSI status of "condition met". Currently only the PRE-FETCH command (see
SBC-4) yields this status.
26 the DEVICE reports a SCSI status of "busy". SAM-6 defines this status as the logical unit is
temporarily unable to process a command. It is recommended to re-issue the command.
27 the DEVICE reports a SCSI status of "task set full".
28 the DEVICE reports a SCSI status of "ACA active". ACA is "auto contingent allegiance" and is
seldom used.
29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "This status shall be returned if
a command is aborted by a command or task management function on another I_T nexus and the Control
mode page TAS bit is set to one".
31 error involving two or more command line options. They may be contradicting, select an unsupported
mode, or a required option (given the context) is missing.
32 there is a logic error in the utility. It corresponds to code comments like "shouldn't/can't get
here". Perhaps the author should be informed.
33 the command sent to DEVICE has timed out.
34 this is a Windows only exit status and indicates that the Windows error number (32 bits) cannot
meaningfully be mapped to an equivalent Unix error number returned as the exit status (7 bits).
36 no error has occurred plus the utility wants to convey a boolean value of false. The corresponding
true value is conveyed by a 0 exit status.
40 the command sent to DEVICE has received an "aborted command" sense key with an additional sense
code of 0x10. This value is related to problems with protection information (PI or DIF). For
example this error may occur when reading a block on a drive that has never been written (or is
unmapped) if that drive was formatted with type 1, 2 or 3 protection.
41 the command sent to DEVICE has received an "aborted command" sense key with an additional sense
code of 0x10 (as with error code) plus a flag indicating the Info field is valid.
48 this is an internal message indicating a NVMe status field (SF) is other than zero after a command
has been executed (i.e. something went wrong). Work in this area is currently experimental.
49 low level driver reports a response's residual count (i.e. number of bytes actually received by
HBA is 'requested_bytes - residual_count') that is nonsensical.
50 OS system calls that fail often return a small integer number to help. In Unix these are called
"errno" values where 0 implies no error. These error codes set aside 51 to 96 for mapping these
errno values but that may not be sufficient. Higher errno values that cannot be mapped are all
mapped to this value (i.e. 50).
Note that an errno value of 0 is mapped to error code 0.
50 + <os_error_number>
OS system calls that fail often return a small integer number to help indicate what the error is.
For example in Unix the inability of a system call to allocate memory returns (in 'errno') ENOMEM
which often is associated with the integer 12. So 62 (i.e. '50 + 12') may be returned by a utility
in this case. It is also possible that a utility in this package reports 50+ENOMEM when it can't
allocate memory, not necessarily from an OS system call. In recent versions of Linux the file
showing the mapping between symbolic constants (e.g. ENOMEM) and the corresponding integer is in
the kernel source code file: include/uapi/asm-generic/errno-base.h
Note that errno values that are greater than or equal to 47 cannot fit in range provided. Instead
they are all mapped to 50 as discussed in the previous entry.
97 a SCSI command response failed sanity checks.
98 the DEVICE reports it has a check condition but the error doesn't fit into any of the above
categories.
99 any errors that can't be categorized into values 1 to 98 may yield this value. This includes
transport and operating system errors after the command has been sent to the device.
100-125
these error codes are used by the ddpt utility which uses the sg3_utils library. They are mainly
specialized error codes associated with offloaded copies.
126 the utility was found but could not be executed. That might occur if the executable does not have
execute permissions.
127 This is the exit status for utility not found. That might occur when a script calls a utility in
this package but the PATH environment variable has not been properly set up, so the script cannot
find the executable.
128 + <signum>
If a signal kills a utility then the exit status is 128 plus the signal number. For example if a
segmentation fault occurs then a utility is typically killed by SIGSEGV which according to 'man 7
signal' has an associated signal number of 11; so the exit status will be 139 .
255 the utility tried to yield an exit status of 255 or larger. That should not happen; given here for
completeness.
Most of the error conditions reported above will be repeatable (an example of one that is not is "unit
attention") so the utility can be run again with the '-v' option (or several) to obtain more information.
COMMON OPTIONS
Arguments to long options are mandatory for short options as well. In the short form an argument to an
option uses zero or more spaces as a separator (i.e. the short form does not use "=" as a separator).
If an option takes a numeric argument then that argument is assumed to be decimal unless otherwise
indicated (e.g. with a leading "0x", a trailing "h" or as noted in the usage message).
Some options are used uniformly in most of the utilities in this package. Those options are listed below.
Note that there are some exceptions.
-d, --dry-run
utilities that can cause lots of user data to be lost or overwritten sometimes have a --dry-run
option. Device modifying actions are typically bypassed (or skipped) to implement a policy of "do
no harm". This allows complex command line invocations to be tested before the action required
(e.g. format a disk) is performed. The --dry-run option has become a common feature of many
command line utilities (e.g. the Unix 'patch' command), not just those from this package.
Note that most hyphenated option names in this package also can be given with an underscore rather
than a hyphen (e.g. --dry_run).
-e, --enumerate
some utilities (e.g. sg_ses and sg_vpd) store a lot of information in internal tables. This option
will output that information in some readable form (e.g. sorted by an acronym or by page number)
then exit. Note that with this option DEVICE is ignored (as are most other options) and no SCSI IO
takes place, so the invoker does not need any elevated permissions.
-h, -?, --help
output the usage message then exit. In a few older utilities the '-h' option requests hexadecimal
output. In these cases the '-?' option will output the usage message then exit.
-H, --hex
for SCSI commands that yield a non-trivial response, print out that response in ASCII hexadecimal.
To produce hexadecimal that can be parsed by other utilities (e.g. without a relative address to
the left and without trailing ASCII) use this option three or four times.
-i, --in=FN
many SCSI commands fetch a significant amount of data (returned in the data-in buffer) which
several of these utilities decode (e.g. sg_vpd and sg_logs). To separate the two steps of fetching
the data from a SCSI device and then decoding it, this option has been added. The first step
(fetching the data) can be done using the --hex or --raw option and redirecting the command line
output to a file (often done with ">" in Unix based operating systems). The difference between
--hex and --raw is that the former produces output in ASCII hexadecimal while --raw produces its
output in "raw" binary.
The second step (i.e. decoding the SCSI response data now held in a file) can be done using this
--in=FN option where the file name is FN. If "-" is used for FN then stdin is assumed, again this
allows for command line redirection (or piping). That file (or stdin) is assumed to contain ASCII
hexadecimal unless the --raw option is also given in which case it is assumed to be binary. Notice
that the meaning of the --raw option is "flipped" when used with --in=FN to act on the input,
typically it acts on the output data.
Since the structure of the data returned by SCSI commands varies considerably then the usage
information or the manpage of the utility being used should be checked. In some cases --hex may
need to be used multiple times (and is more conveniently given as '-HH' or '-HHH).
-i, --inhex=FN
This option has the same or similar functionality as --in=FN. And perhaps 'inhex' is more
descriptive since by default, ASCII hexadecimal is expected in the contents of file: FN.
Alternatively the short form option may be -I or -X. See the "FORMAT OF FILES CONTAINING ASCII
HEX" section below for more information.
-m, --maxlen=LEN
several important SCSI commands (e.g. INQUIRY and MODE SENSE) have response lengths that vary
depending on many factors, only some of which these utilities take into account. The maximum
response length is typically specified in the 'allocation length' field of the cdb. In the absence
of this option, several utilities use a default allocation length (sometimes recommended in the
SCSI draft standards) or a "double fetch" strategy. See sg_logs(8) for its description of a
"double fetch" strategy. These techniques are imperfect and in the presence of faulty SCSI targets
can cause problems (e.g. some USB mass storage devices freeze if they receive an INQUIRY
allocation length other than 36). Also use of this option disables any "double fetch" strategy
that may have otherwise been used.
-r, --raw
for SCSI commands that yield a non-trivial response, output that response in binary to stdout. If
any error messages or warning are produced they are usually sent to stderr so as to not interfere
with the output from this option.
Some utilities that consume data to send to the DEVICE along with the SCSI command, use this
option. Alternatively the --in=FN option causes DEVICE to be ignored and the response data (to be
decoded) fetched from a file named FN. In these cases this option may indicate that binary data
can be read from stdin or from a nominated file (e.g. FN).
-t, --timeout=SECS
utilities that issue potentially long-running SCSI commands often have a --timeout=SECS option.
This typically instructs the operating system to abort the SCSI command in question once the
timeout expires. Aborting SCSI commands is typically a messy business and in the case of format
like commands may leave the device in a "format corrupt" state requiring another long-running
re-initialization command to be sent. The argument, SECS, is usually in seconds and the short form
of the option may be something other than -t since the timeout option was typically added later as
storage devices grew in size and initialization commands took longer. Since many utilities had
relatively long internal command timeouts before this option was introduced, the actual command
timeout given to the operating systems is the higher of the internal timeout and SECS.
Many long running SCSI commands have an IMMED bit which causes the command to finish relatively
quickly but the initialization process to continue. In such cases the REQUEST SENSE command can be
used to monitor progress with its progress indication field (see the sg_requests and sg_turs
utilities). Utilities that send such SCSI command either have an --immed option or a --wait
option which is the logical inverse of the "immediate" action.
-v, --verbose
increase the level of verbosity, (i.e. debug output). Can be used multiple times to further
increase verbosity. The additional output caused by this option is almost always sent to stderr.
-V, --version
print the version string and then exit. Each utility has its own version number and date of last
code change.
NUMERIC ARGUMENTS
Many utilities have command line options that take numeric arguments. These numeric arguments can be
large values (e.g. a logical block address (LBA) on a disk) and can be inconvenient to enter in the
default decimal representation. So various other representations are permitted.
Multiplicative suffixes are accepted. They are one, two or three letter strings appended directly after
the number to which they apply:
c C *1
w W *2
b B *512
k K KiB *1024
KB kB *1000
m M MiB *1048576
MB mB *1000000
g G GiB *(2^30)
GB gB *(10^9)
t T TiB *(2^40)
TB *(10^12)
p P PiB *(2^50)
PB *(10^15)
An example is "2k" for 2048. The large tera and peta suffixes are only available for numeric arguments
that might require 64 bits to represent internally.
These multiplicative suffixes are compatible with GNU's dd command (since 2002) which claims compliance
with SI and with IEC 60027-2.
A suffix of the form "x<n>" multiplies the preceding number by <n>. An example is "2x33" for "66". The
left argument cannot be '0' as '0x' will be interpreted as hexadecimal number prefix (see below). The
left argument to the multiplication must end in a hexadecimal digit (i.e. 0 to f) and the whole
expression cannot have any embedded whitespace (e.g. spaces). An ugly example: "0xfx0x2" for 30.
A suffix of the form "+<n>" adds the preceding number to <n>. An example is "3+1k" for "1027". The left
argument to the addition must end in a hexadecimal digit (i.e. 0 to f) and the whole expression cannot
have any embedded whitespace (e.g. spaces). Another example: "0xf+0x2" for 17.
Alternatively numerical arguments can be given in hexadecimal. There are two syntaxes. The number can be
preceded by either "0x" or "0X" as found in the C programming language. The second hexadecimal
representation is a trailing "h" or "H" as found in (storage) standards. When hex numbers are given,
multipliers cannot be used. For example the decimal value "256" can be given as "0x100" or "100h".
FORMAT OF FILES CONTAINING ASCII HEX
Such a file is assumed to contain a sequence of one or two digit ASCII hexadecimal values separated by
whitespace. "Whitespace consists of either spaces, tabs, blank lines, or any combination thereof". Each
one or two digit ASCII hex pair is decoded into a byte (i.e. 8 bits). The following will be decoded to
valid (ascending valued) bytes: '0', '01', '3', 'c', 'F', '4a', 'cC', 'ff'. Lines containing only
whitespace are ignored. The contents of any line containing a hash mark ('#') is ignored from that point
until the end of that line. Users are encouraged to use hash marks to introduce comments in hex files.
The author uses the extension'.hex' on such files. Examples can be found in the 'inhex' directory.
MICROCODE AND FIRMWARE
There are two standardized methods for downloading microcode (i.e. device firmware) to a SCSI device. The
more general way is with the SCSI WRITE BUFFER command, see the sg_write_buffer utility. SCSI enclosures
have their own method based on the Download microcode control/status diagnostic page, see the
sg_ses_microcode utility.
SCRIPTS, EXAMPLES and UTILS
There are several bash shell scripts in the 'scripts' subdirectory that invoke compiled utilities (e.g.
sg_readcap). Several of the scripts start with 'scsi_' rather than 'sg_'. One purpose of these scripts is
to call the same utility (e.g. sg_readcap) on multiple devices. Most of the basic compiled utilities only
allow one device as an argument. Some distributions install these scripts in a more visible directory
(e.g. /usr/bin). Some of these scripts have man page entries. See the README file in the 'scripts'
subdirectory.
There is some example C code plus examples of complex invocations in the 'examples' subdirectory. There
is also a README file. The example C may be a simpler example of how to use a SCSI pass-through in Linux
than the main utilities (found in the 'src' subdirectory). This is due to the fewer abstraction layers
(e.g. they don't worry the MinGW in Windows may open a file in text rather than binary mode).
Some utilities that the author has found useful have been placed in the 'utils' subdirectory.
WEB SITE
There is a web page discussing this package at http://sg.danny.cz/sg/sg3_utils.html . The device naming used by this package on various operating systems is discussed at: http://sg.danny.cz/sg/device_name.html . There is a git code mirror at https://github.com/hreinecke/sg3_utils . The principle code repository uses subversion and is on the author's equipment. The author keeps track of this via the subversion revision number which is an ascending integer (currently at 774 for this package). The github mirror gets updated periodically from the author's repository. Depending on the time of update, the above Downloads section at sg.danny.cz may be more up to date than the github mirror.
AUTHORS
Written by Douglas Gilbert. Some utilities have been contributed, see the CREDITS file and individual
source files (in the 'src' directory).
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 1999-2021 Douglas Gilbert
Some utilities are distributed under a GPL version 2 license while others, usually more recent ones, are
under a FreeBSD license. The files that are common to almost all utilities and thus contain the most
reusable code, namely sg_lib.[hc], sg_cmds_basic.[hc] and sg_cmds_extra.[hc] are under a FreeBSD license.
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sdparm(sdparm), ddpt(ddpt), lsscsi(lsscsi), dmesg(1), mt(1)