Provided by: libcpuset1_1.0-4_amd64 
NAME
cpuset - confine tasks to processor and memory node subsets
DESCRIPTION
The cpuset file system is a pseudo-filesystem interface to the kernel cpuset mechanism for controlling
the processor and memory placement of tasks. It is commonly mounted at /dev/cpuset.
A cpuset defines a list of CPUs and memory nodes. Cpusets are represented as directories in a
hierarchical virtual file system, where the top directory in the hierarchy (/dev/cpuset) represents the
entire system (all online CPUs and memory nodes) and any cpuset that is the child (descendant) of another
parent cpuset contains a subset of that parents CPUs and memory nodes. The directories and files
representing cpusets have normal file system permissions.
Every task in the system belongs to exactly one cpuset. A task is confined to only run on the CPUs in
the cpuset it belongs to, and to allocate memory only on the memory nodes in that cpuset. When a task
forks, the child task is placed in the same cpuset as its parent. With sufficient privilege, a task may
be moved from one cpuset to another and the allowed CPUs and memory nodes of an existing cpuset may be
changed.
When the system begins booting, only the top cpuset is defined and all tasks are in that cpuset. During
the boot process or later during normal system operation, other cpusets may be created, as sub-
directories of the top cpuset under the control of the system administrator and tasks may be placed in
these other cpusets.
Cpusets are integrated with the sched_setaffinity(2) scheduling affinity mechanism and the mbind(2) and
set_mempolicy(2) memory placement mechanisms in the kernel. Neither of these mechanisms let a task make
use of a CPU or memory node that is not allowed by cpusets. If changes to a tasks cpuset placement
conflict with these other mechanisms, then cpuset placement is enforced even if it means overriding these
other mechanisms.
Typically, a cpuset is used to manage the CPU and memory node confinement for the entire set of tasks in
a job, and these other mechanisms are used to manage the placement of individual tasks or memory regions
within a job.
FILES
Each directory below /dev/cpuset represents a cpuset and contains several files describing the state of
that cpuset.
New cpusets are created using the mkdir system call or shell command. The properties of a cpuset, such
as its flags, allowed CPUs and memory nodes, and attached tasks, are queried and modified by reading or
writing to the appropriate file in that cpusets directory, as listed below.
The files in each cpuset directory are automatically created when the cpuset is created, as a result of
the mkdir invocation. It is not allowed to add or remove files from a cpuset directory.
The files in each cpuset directory are small text files that may be read and written using traditional
shell utilities such as cat(1), and echo(1), or using ordinary file access routines from programmatic
languages, such as open(2), read(2), write(2) and close(2) from the 'C' library. These files represent
internal kernel state and do not have any persistent image on disk. Each of these per-cpuset files is
listed and described below.
tasks
List of the process IDs (PIDs) of the tasks in that cpuset. The list is formatted as a series of
ASCII decimal numbers, each followed by a newline. A task may be added to a cpuset (removing it
from the cpuset previously containing it) by writing its PID to that cpusets tasks file (with or
without a trailing newline.)
Beware that only one PID may be written to the tasks file at a time. If a string is written that
contains more than one PID, only the first one will be considered.
notify_on_release
Flag (0 or 1). If set (1), that cpuset will receive special handling whenever its last using task
and last child cpuset goes away. See the Notify On Release section, below.
cpus
List of CPUs on which tasks in that cpuset are allowed to execute. See List Format below for a
description of the format of cpus.
The CPUs allowed to a cpuset may be changed by writing a new list to its cpus file. Note however,
such a change does not take affect until the PIDs of the tasks in the cpuset are rewritten to the
cpusets tasks file. See the WARNINGS section, below.
cpu_exclusive
Flag (0 or 1). If set (1), the cpuset has exclusive use of its CPUs (no sibling or cousin cpuset
may overlap CPUs). By default this is off (0). Newly created cpusets also initially default this
to off (0).
mems
List of memory nodes on which tasks in that cpuset are allowed to allocate memory. See List
Format below for a description of the format of mems.
mem_exclusive
Flag (0 or 1). If set (1), the cpuset has exclusive use of its memory nodes (no sibling or cousin
may overlap). By default this is off (0). Newly created cpusets also initially default this to
off (0).
memory_migrate
Flag (0 or 1). If set (1), then memory migration is enabled. See the Memory Migration section,
below.
memory_pressure
A measure of how much memory pressure the tasks in this cpuset are causing. See the Memory
Pressure section, below. Unless memory_pressure_enabled is enabled, always has value zero (0).
This file is read-only. See the WARNINGS section, below.
memory_pressure_enabled
Flag (0 or 1). This file is only present in the root cpuset, normally /dev/cpuset. If set (1),
the memory_pressure calculations are enabled for all cpusets in the system. See the Memory
Pressure section, below.
memory_spread_page
Flag (0 or 1). If set (1), the kernel page cache (file system buffers) are uniformly spread
across the cpuset. See the Memory Spread section, below.
memory_spread_slab
Flag (0 or 1). If set (1), the kernel slab caches for file I/O (directory and inode structures)
are uniformly spread across the cpuset. See the Memory Spread section, below.
In addition to the above special files in each directory below /dev/cpuset, each task under /proc has an
added file named cpuset, displaying the cpuset name, as the path relative to the root of the cpuset file
system.
Also the /proc/<pid>/status file for each task has two added lines, displaying the tasks cpus_allowed (on
which CPUs it may be scheduled) and mems_allowed (on which memory nodes it may obtain memory), in the
Mask Format (see below) as shown in the following example:
Cpus_allowed: ffffffff,ffffffff,ffffffff,ffffffff
Mems_allowed: ffffffff,ffffffff
EXTENDED CAPABILITIES
In addition to controlling which cpus and mems a task is allowed to use, cpusets provide the following
extended capabilities.
Exclusive Cpusets
If a cpuset is marked cpu_exclusive or mem_exclusive, no other cpuset, other than a direct ancestor or
descendant, may share any of the same CPUs or memory nodes.
A cpuset that is cpu_exclusive has a scheduler (sched) domain associated with it. The sched domain
consists of all CPUs in the current cpuset that are not part of any exclusive child cpusets. This
ensures that the scheduler load balancing code only balances against the CPUs that are in the sched
domain as defined above and not all of the CPUs in the system. This removes any overhead due to load
balancing code trying to pull tasks outside of the cpu_exclusive cpuset only to be prevented by the
tasks' cpus_allowed mask.
A cpuset that is mem_exclusive restricts kernel allocations for page, buffer and other data commonly
shared by the kernel across multiple users. All cpusets, whether mem_exclusive or not, restrict
allocations of memory for user space. This enables configuring a system so that several independent jobs
can share common kernel data, such as file system pages, while isolating each jobs user allocation in its
own cpuset. To do this, construct a large mem_exclusive cpuset to hold all the jobs, and construct
child, non-mem_exclusive cpusets for each individual job. Only a small amount of typical kernel memory,
such as requests from interrupt handlers, is allowed to be taken outside even a mem_exclusive cpuset.
Notify On Release
If the notify_on_release flag is enabled (1) in a cpuset, then whenever the last task in the cpuset
leaves (exits or attaches to some other cpuset) and the last child cpuset of that cpuset is removed, the
kernel will run the command /sbin/cpuset_release_agent, supplying the pathname (relative to the mount
point of the cpuset file system) of the abandoned cpuset. This enables automatic removal of abandoned
cpusets.
The default value of notify_on_release in the root cpuset at system boot is disabled (0). The default
value of other cpusets at creation is the current value of their parents notify_on_release setting.
The command /sbin/cpuset_release_agent is invoked, with the name (/dev/cpuset relative path) of that
cpuset in argv[1]. This supports automatic cleanup of abandoned cpusets.
The usual contents of the command /sbin/cpuset_release_agent is simply the shell script:
#!/bin/sh
rmdir /dev/cpuset/$1
By default, notify_on_release is off (0). Newly created cpusets inherit their notify_on_release setting
from their parent cpuset.
As with other flag values below, this flag can be changed by writing an ASCII number 0 or 1 (with
optional trailing newline) into the file, to clear or set the flag, respectively.
Memory Pressure
The memory_pressure of a cpuset provides a simple per-cpuset metric of the rate that the tasks in a
cpuset are attempting to free up in use memory on the nodes of the cpuset to satisfy additional memory
requests.
This enables batch managers monitoring jobs running in dedicated cpusets to efficiently detect what level
of memory pressure that job is causing.
This is useful both on tightly managed systems running a wide mix of submitted jobs, which may choose to
terminate or re-prioritize jobs that are trying to use more memory than allowed on the nodes assigned
them, and with tightly coupled, long running, massively parallel scientific computing jobs that will
dramatically fail to meet required performance goals if they start to use more memory than allowed to
them.
This mechanism provides a very economical way for the batch manager to monitor a cpuset for signs of
memory pressure. It's up to the batch manager or other user code to decide what to do about it and take
action.
Unless memory pressure calculation is enabled by setting the special file
/dev/cpuset/memory_pressure_enabled, it is not computed for any cpuset, and always reads a value of zero.
See the WARNINGS section, below.
Why a per-cpuset, running average:
Because this meter is per-cpuset rather than per-task or mm, the system load imposed by a batch
scheduler monitoring this metric is sharply reduced on large systems, because a scan of the tasklist
can be avoided on each set of queries.
Because this meter is a running average rather than an accumulating counter, a batch scheduler can
detect memory pressure with a single read, instead of having to read and accumulate results for a
period of time.
Because this meter is per-cpuset rather than per-task or mm, the batch scheduler can obtain the key
information, memory pressure in a cpuset, with a single read, rather than having to query and
accumulate results over all the (dynamically changing) set of tasks in the cpuset.
A per-cpuset simple digital filter is kept within the kernel, and updated by any task attached to that
cpuset, if it enters the synchronous (direct) page reclaim code.
A per-cpuset file provides an integer number representing the recent (half-life of 10 seconds) rate of
direct page reclaims caused by the tasks in the cpuset, in units of reclaims attempted per second, times
1000.
Memory Spread
There are two Boolean flag files per cpuset that control where the kernel allocates pages for the file
system buffers and related in kernel data structures. They are called memory_spread_page and
memory_spread_slab.
If the per-cpuset Boolean flag file memory_spread_page is set, then the kernel will spread the file
system buffers (page cache) evenly over all the nodes that the faulting task is allowed to use, instead
of preferring to put those pages on the node where the task is running.
If the per-cpuset Boolean flag file memory_spread_slab is set, then the kernel will spread some file
system related slab caches, such as for inodes and directory entries evenly over all the nodes that the
faulting task is allowed to use, instead of preferring to put those pages on the node where the task is
running.
The setting of these flags does not affect anonymous data segment or stack segment pages of a task.
By default, both kinds of memory spreading are off and the kernel prefers to allocate memory pages on the
node local to where the requesting task is running. If that node is not allowed by the tasks NUMA
mempolicy or cpuset configuration or if there are insufficient free memory pages on that node, then the
kernel looks for the nearest node that is allowed and does have sufficient free memory.
When new cpusets are created, they inherit the memory spread settings of their parent.
Setting memory spreading causes allocations for the affected page or slab caches to ignore the tasks NUMA
mempolicy and be spread instead. Tasks using mbind() or set_mempolicy() calls to set NUMA mempolicies
will not notice any change in these calls as a result of their containing tasks memory spread settings.
If memory spreading is turned off, the currently specified NUMA mempolicy once again applies to memory
page allocations.
Both memory_spread_page and memory_spread_slab are Boolean flag files. By default they contain "0",
meaning that the feature is off for that cpuset. If a "1" is written to that file, that turns the named
feature on.
This memory placement policy is also known (in other contexts) as round-robin or interleave.
This policy can provide substantial improvements for jobs that need to place thread local data on the
corresponding node, but that need to access large file system data sets that need to be spread across the
several nodes in the jobs cpuset in order to fit. Without this policy, especially for jobs that might
have one thread reading in the data set, the memory allocation across the nodes in the jobs cpuset can
become very uneven.
Memory Migration
Normally, under the default setting (disabled) of memory_migrate, once a page is allocated (given a
physical page of main memory) then that page stays on whatever node it was allocated, so long as it
remains allocated, even if the cpusets memory placement policy mems subsequently changes.
When memory migration is enabled in a cpuset, if the mems setting of the cpuset is changed, then any
memory page in use by any task in the cpuset that is on a memory node no longer allowed will be migrated
to a memory node that is allowed.
Also if a task is moved into a cpuset with memory_migrate enabled, any memory pages it uses that were on
memory nodes allowed in its previous cpuset, but which are not allowed in its new cpuset, will be
migrated to a memory node allowed in the new cpuset.
The relative placement of a migrated page within the cpuset is preserved during these migration
operations if possible. For example, if the page was on the second valid node of the prior cpuset, then
the page will be placed on the second valid node of the new cpuset, if possible.
FORMATS
The following formats are used to represent sets of CPUs and memory nodes.
Mask Format
The Mask Format is used to represent CPU and memory node bitmasks in the /proc/<pid>/status file.
It is hexadecimal, using ASCII characters "0" - "9" and "a" - "f". This format displays each 32-bit word
in hex (zero filled) and for masks longer than one word uses a comma separator between words. Words are
displayed in big-endian order most significant first. And hex digits within a word are also in big-endian
order.
The number of 32-bit words displayed is the minimum number needed to display all bits of the bitmask,
based on the size of the bitmask.
Examples of the Mask Format:
00000001 # just bit 0 set
80000000,00000000,00000000 # just bit 95 set
00000001,00000000,00000000 # just bit 64 set
000000ff,00000000 # bits 32-39 set
00000000,000E3862 # 1,5,6,11-13,17-19 set
A mask with bits 0, 1, 2, 4, 8, 16, 32 and 64 set displays as "00000001,00000001,00010117". The first
"1" is for bit 64, the second for bit 32, the third for bit 16, the fourth for bit 8, the fifth for bit
4, and the "7" is for bits 2, 1 and 0.
List Format
The List Format for cpus and mems is a comma separated list of CPU or memory node numbers and ranges of
numbers, in ASCII decimal.
Examples of the List Format:
0-4,9 # bits 0, 1, 2, 3, 4 and 9 set
0-2,7,12-14 # bits 0, 1, 2, 7, 12, 13 and 14 set
RULES
The following rules apply to each cpuset:
* Its CPUs and memory nodes must be a (possibly equal) subset of its parents.
* It can only be marked cpu_exclusive if its parent is.
* It can only be marked mem_exclusive if its parent is.
* If it is cpu_exclusive, its CPUs may not overlap any sibling.
* If it is memory_exclusive, its memory nodes may not overlap any sibling.
PERMISSIONS
The permissions of a cpuset are determined by the permissions of the special files and directories in the
cpuset file system, normally mounted at /dev/cpuset.
For instance, a task can put itself in some other cpuset (than its current one) if it can write the tasks
file for that cpuset (requires execute permission on the encompassing directories and write permission on
that tasks file).
An additional constraint is applied to requests to place some other task in a cpuset. One task may not
attach another to a cpuset unless it would have permission to send that task a signal.
A task may create a child cpuset if it can access and write the parent cpuset directory. It can modify
the CPUs or memory nodes in a cpuset if it can access that cpusets directory (execute permissions on the
encompassing directories) and write the corresponding cpus or mems file.
Note however that since changes to the CPUs of a cpuset don't apply to any task in that cpuset until said
task is reattached to that cpuset, it would normally not be a good idea to arrange the permissions on a
cpuset so that some task could write the cpus file unless it could also write the tasks file to reattach
the tasks therein.
There is one minor difference between the manner in which these permissions are evaluated and the manner
in which normal file system operation permissions are evaluated. The kernel evaluates relative pathnames
starting at a tasks current working directory. Even if one is operating on a cpuset file, relative
pathnames are evaluated relative to the current working directory, not relative to a tasks current
cpuset. The only ways that cpuset paths relative to a tasks current cpuset can be used are if either the
tasks current working directory is its cpuset (it first did a cd or chdir to its cpuset directory beneath
/dev/cpuset, which is a bit unusual) or if some user code converts the relative cpuset path to a full
file system path.
WARNINGS
Updating a cpusets cpus
Changes to a cpusets cpus file do not take affect for any task in that cpuset until that tasks process ID
(PID) is rewritten to the cpusets tasks file. This unusual requirement is needed to optimize a critical
code path in the Linux kernel. Beware that only one PID can be written at a time to a cpusets tasks
file. Additional PIDs on a single write(2) system call are ignored. One (unobvious) way to satisfy this
requirement to rewrite the tasks file after updating the cpus file is to use the -u unbuffered option to
the sed(1) command, as in the following scenario:
cd /dev/cpuset/foo # /foo is an existing cpuset
/bin/echo 3 > cpus # change /foo's cpus
sed -un p < tasks > tasks # rewrite /foo's tasks file
If one examines the Cpus_allowed value in the /proc/<pid>/status file for one of the tasks in cpuset /foo
in the above scenario, one will notice that the value does not change when the cpus file is written (the
echo command), but only later, after the tasks file is rewritten (the sed command).
Enabling memory_pressure
By default, the per-cpuset file memory_pressure always contains zero (0). Unless this feature is enabled
by writing "1" to the special file /dev/cpuset/memory_pressure_enabled, the kernel does not compute per-
cpuset memory_pressure.
Using the echo command
When using the echo command at the shell prompt to change the values of cpuset files, beware that most
shell built-in echo commands to not display an error message if the write(2) system call fails. For
example, if the command:
echo 19 > mems
failed because memory node 19 was not allowed (perhaps the current system does not have a memory node
19), then the above echo command would not display any error. It is better to use the /bin/echo external
command to change cpuset file settings, as this command will display write(2) errors, as in the example:
/bin/echo 19 > mems
/bin/echo: write error: No space left on device
EXCEPTIONS
Not all allocations of system memory are constrained by cpusets, for the following reasons.
If hot-plug functionality is used to remove all the CPUs that are currently assigned to a cpuset, then
the kernel will automatically update the cpus_allowed of all tasks attached to CPUs in that cpuset to
allow all CPUs. When memory hot-plug functionality for removing memory nodes is available, a similar
exception is expected to apply there as well. In general, the kernel prefers to violate cpuset
placement, over starving a task that has had all its allowed CPUs or memory nodes taken offline. User
code should reconfigure cpusets to only refer to online CPUs and memory nodes when using hot-plug to add
or remove such resources.
A few kernel critical internal memory allocation requests, marked GFP_ATOMIC, must be satisfied,
immediately. The kernel may drop some request or malfunction if one of these allocations fail. If such
a request cannot be satisfied within the current tasks cpuset, then we relax the cpuset, and look for
memory anywhere we can find it. It's better to violate the cpuset than stress the kernel.
Allocations of memory requested by kernel drivers while processing an interrupt lack any relevant task
context, and are not confined by cpusets.
LIMITATIONS
Kernel limitations updating cpusets
In order to minimize the impact of cpusets on critical kernel code, such as the scheduler, and due to the
fact that the kernel does not support one task updating the memory placement of another task directly,
the impact on a task of changing its cpuset CPU or memory node placement, or of changing to which cpuset
a task is attached, is subtle.
If a cpuset has its memory nodes modified, then for each task attached to that cpuset, the next time that
the kernel attempts to allocate a page of memory for that task, the kernel will notice the change in the
tasks cpuset, and update its per-task memory placement to remain within the new cpusets memory placement.
If the task was using mempolicy MPOL_BIND, and the nodes to which it was bound overlap with its new
cpuset, then the task will continue to use whatever subset of MPOL_BIND nodes are still allowed in the
new cpuset. If the task was using MPOL_BIND and now none of its MPOL_BIND nodes are allowed in the new
cpuset, then the task will be essentially treated as if it was MPOL_BIND bound to the new cpuset (even
though its NUMA placement, as queried by get_mempolicy(), doesn't change). If a task is moved from one
cpuset to another, then the kernel will adjust the tasks memory placement, as above, the next time that
the kernel attempts to allocate a page of memory for that task.
If a cpuset has its CPUs modified, each task using that cpuset does _not_ change its behavior
automatically. In order to minimize the impact on the critical scheduling code in the kernel, tasks will
continue to use their prior CPU placement until they are rebound to their cpuset, by rewriting their PID
to the 'tasks' file of their cpuset. If a task had been bound to some subset of its cpuset using the
sched_setaffinity() call, and if any of that subset is still allowed in its new cpuset settings, then the
task will be restricted to the intersection of the CPUs it was allowed on before, and its new cpuset CPU
placement. If, on the other hand, there is no overlap between a tasks prior placement and its new cpuset
CPU placement, then the task will be allowed to run on any CPU allowed in its new cpuset. If a task is
moved from one cpuset to another, its CPU placement is updated in the same way as if the tasks PID is
rewritten to the 'tasks' file of its current cpuset.
In summary, the memory placement of a task whose cpuset is changed is updated by the kernel, on the next
allocation of a page for that task, but the processor placement is not updated, until that tasks PID is
rewritten to the 'tasks' file of its cpuset. This is done to avoid impacting the scheduler code in the
kernel with a check for changes in a tasks processor placement.
Rename limitations
You can use the rename(2) system call to rename cpusets. Only simple renaming is supported, changing the
name of a cpuset directory while keeping its same parent.
NOTES
Despite its name, the pid parameter is actually a thread id, and each thread in a threaded group can be
attached to a different cpuset. The value returned from a call to gettid(2) can be passed in the
argument pid.
EXAMPLES
The following examples demonstrate querying and setting cpuset options using shell commands.
Creating and attaching to a cpuset.
To create a new cpuset and attach the current command shell to it, the steps are:
1) mkdir /dev/cpuset (if not already done)
2) mount -t cpuset none /dev/cpuset (if not already done)
3) Create the new cpuset using mkdir(1).
4) Assign CPUs and memory nodes to the new cpuset.
5) Attach the shell to the new cpuset.
For example, the following sequence of commands will setup a cpuset named "Charlie", containing just CPUs
2 and 3, and memory node 1, and then attach the current shell to that cpuset.
mkdir /dev/cpuset
mount -t cpuset cpuset /dev/cpuset
cd /dev/cpuset
mkdir Charlie
cd Charlie
/bin/echo 2-3 > cpus
/bin/echo 1 > mems
/bin/echo $$ > tasks
# The current shell is now running in cpuset Charlie
# The next line should display '/Charlie'
cat /proc/self/cpuset
Migrating a job to different memory nodes.
To migrate a job (the set of tasks attached to a cpuset) to different CPUs and memory nodes in the
system, including moving the memory pages currently allocated to that job, perform the following steps.
1) Lets say we want to move the job in cpuset alpha (CPUs 4-7 and memory nodes 2-3) to a new cpuset
beta (CPUs 16-19 and memory nodes 8-9).
2) First create the new cpuset beta.
3) Then allow CPUs 16-19 and memory nodes 8-9 in beta.
4) Then enable memory_migration in beta.
5) Then move each task from alpha to beta.
The following sequence of commands accomplishes this.
cd /dev/cpuset
mkdir beta
cd beta
/bin/echo 16-19 > cpus
/bin/echo 8-9 > mems
/bin/echo 1 > memory_migrate
while read i; do /bin/echo $i; done < ../alpha/tasks > tasks
The above should move any tasks in alpha to beta, and any memory held by these tasks on memory nodes 2-3
to memory nodes 8-9, respectively.
Notice that the last step of the above sequence did not do:
cp ../alpha/tasks tasks
The while loop, rather than the seemingly easier use of the cp(1) command, was necessary because only one
task PID at a time may be written to the tasks file.
The same affect (writing one pid at a time) as the while loop can be accomplished more efficiently, in
fewer keystrokes and in syntax that works on any shell, but alas more obscurely, by using the sed -u
[unbuffered] option:
sed -un p < ../alpha/tasks > tasks
ERRORS
The Linux kernel implementation of cpusets sets errno to specify the reason for a failed system call
affecting cpusets.
The possible errno settings and their meaning when set on a failed cpuset call are as listed below.
ENOMEM Insufficient memory is available.
EBUSY Attempted to remove a cpuset with attached tasks.
EBUSY Attempted to remove a cpuset with child cpusets.
ENOENT Attempted to create a cpuset in a parent cpuset that doesn't exist.
ENOENT Attempted to access a non-existent file in a cpuset directory.
EEXIST Attempted to create a cpuset that already exists.
EEXIST Attempted to rename(2) a cpuset to a name that already exists.
ENOTDIR
Attempted to rename(2) a non-existent cpuset.
E2BIG Attempted a write(2) system call on a special cpuset file with a length larger than some kernel
determined upper limit on the length of such writes.
ESRCH Attempted to write the process ID (PID) of a non-existent task to a cpuset tasks file.
EACCES Attempted to write the process ID (PID) of a task to a cpuset tasks file when one lacks permission
to move that task.
EACCESS
Attempted to write(2) a memory_pressure file.
ENOSPC Attempted to write the process ID (PID) of a task to a cpuset tasks file when the cpuset had an
empty cpus or empty mems setting.
EINVAL Attempted to change a cpuset in a way that would violate a cpu_exclusive or mem_exclusive
attribute of that cpuset or any of its siblings.
EINVAL Attempted to write(2) an empty cpus or mems list to the kernel. The kernel creates new cpusets
(via mkdir(2)) with empty cpus and mems. But the kernel will not allow an empty list to be
written to the special cpus or mems files of a cpuset.
EIO Attempted to write(2) a string to a cpuset tasks file that does not begin with an ASCII decimal
integer.
EIO Attempted to rename(2) a cpuset outside of its current directory.
ENOSPC Attempted to write(2) a list to a cpus file that did not include any online CPUs.
ENOSPC Attempted to write(2) a list to a mems file that did not include any online memory nodes.
ENODEV The cpuset was removed by another task at the same time as a write(2) was attempted on one of the
special files in the cpuset directory.
EACCES Attempted to add a CPU or memory node to a cpuset that is not already in its parent.
EACCES Attempted to set cpu_exclusive or mem_exclusive on a cpuset whose parent lacks the same setting.
EBUSY Attempted to remove a CPU or memory node from a cpuset that is also in a child of that cpuset.
EFAULT Attempted to read(2) or write(2) a cpuset file using a buffer that is outside your accessible
address space.
ENAMETOOLONG
Attempted to read a /proc/<pid>/cpuset file for a cpuset path that is longer than the kernel page
size.
ENAMETOOLONG
Attempted to create a cpuset whose base directory name is longer than 255 characters.
ENAMETOOLONG
Attempted to create a cpuset whose full pathname including the "/dev/cpuset/" prefix is longer
than 4095 characters.
EINVAL Specified a cpus or mems list to the kernel which included a range with the second number smaller
than the first number.
EINVAL Specified a cpus or mems list to the kernel which included an invalid character in the string.
ERANGE Specified a cpus or mems list to the kernel which included a number too large for the kernel to
set in its bitmasks.
SEE ALSO
cat(1), echo(1), ls(1), mkdir(1), rmdir(1), sed(1), taskset(1), close(2), get_mempolicy(2), mbind(2),
mkdir(2), open(2), read(2) rmdir(2), sched_getaffinity(2), sched_setaffinity(2), set_mempolicy(2),
sched_setscheduler(2), taskset(2), write(2), libbitmask(3), proc(5), migratepages(8), numactl(8).
HISTORY
Cpusets appeared in version 2.6.13 of the Linux kernel.
BUGS
memory_pressure cpuset files can be opened for writing, creation or truncation, but then the write(2)
fails with errno == EACCESS, and the creation and truncation options on open(2) have no affect.
AUTHOR
This man page was written by Paul Jackson.
Linux 2.6 2006-05-25 CPUSET(4)